/       /       /    48 Volts, 5 Amps and 240 Watts, or the Power Supply That Managed to Surprise Me
Support the project on Patreon


48 Volts, 5 Amps and 240 Watts, or the Power Supply That Managed to Surprise Me

$20.94
Go to store
Many of you know how much I like different power supplies. I’ve reviewed power supplies rated for 5, 12, 24, and 36 V, and today it’s time for the next step: a 48 V power supply.
So, a 48 V, 240 W power supply has landed on my workbench. We’ll take it apart, measure it, test it, and, of course, analyze it.

It’s been quite a while since I last took a power supply apart. I was even starting to miss it.
I’ve had this power supply for a long time, but somehow never got around to it. Now I have, especially since it’s a pretty useful unit.

It arrived in the same standard white box as all the others. This kind of packaging is used even for branded power supplies.
The power supply is housed in a metal case.
One side has a switch for selecting the input voltage range.
The other side has a label with the following specifications:
Input voltage: 110/220 V
Output voltage: 48 V
Output current: 5 A
Maximum power: 240 W
Dimensions: 200 x 110 x 50 mm

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

I have no complaints about the power supply’s exterior. It looks much like hundreds of other power supplies in this form factor, apart from its size, perhaps.
There is one small difference, though.
The 36 V, 10 A model from my previous review was the mirror image of this one.
That can sometimes matter.

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

One end has a terminal block for connecting the input power, ground, and load.
The terminal block has three output terminals, but they’re connected together inside since this is a single-output power supply. This can be handy when connecting several devices, and is most often found on relatively high-power supplies.

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

This time, the terminal block cover can’t be opened to 90 degrees, unlike on the previous models. It’s a small drawback, but a drawback nonetheless.
Tucked between the case and the terminal block are the output voltage adjustment knob and the power indicator LED. They’re really tucked away—you could easily miss them at a glance.

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

There’s nothing else to see on the outside, so let’s take a look inside :)
Inside, it’s the same classic design: an L-shaped chassis covered by a matching perforated L-shaped lid. The chassis is aluminum; the lid is steel.

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

Let’s take a closer look. The first thing that caught my eye was the transformer, which is quite large for this power rating—though that’s normal for passive cooling.
With active cooling, the transformer would probably be smaller.
I remember those cheap JNC computer power supplies rated at 300 W, with a transformer smaller than a matchbox.
Otherwise, it’s a classic design with plenty of space between components.

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

It looks exactly like the 36 V power supply from my previous review, but, as I mentioned above, it’s a mirror image. Compare the photos of the two supplies and you’ll see what I mean.

48 V, 5 A, and 240 W—or the power supply that managed to surprise me48 V, 5 A, and 240 W—or the power supply that managed to surprise me

Let's go over the critical parts—a quick initial visual inspection and analysis, so to speak.
As always, we'll start with the mains filter.
It's present. The only missing part is the X2 capacitor after the choke (on the power-supply side, not the mains side), but in my opinion it's not critical.

48 V, 5 A and 240 W, or a power supply that managed to surprise me48 V, 5 A and 240 W, or a power supply that managed to surprise me

Now let's take a closer look. We'll also go over what to look for when choosing a power supply.
1. X2 filter capacitor (gray), a two-winding common-mode choke, and a pair of Y2 capacitors. Everything is in place; no issues here.
2. A capacitor from the power supply's negative output to its case. It's a regular high-voltage capacitor here. A Y2 would be better, but it's not that critical in this position, so I'll let it slide.
3. The input bridge rectifier is a T20XB60. The manufacturer specifies a maximum current of up to 20 A (when mounted on a heatsink, of course) and a voltage rating of up to 600 V (peak).
That's excellent for this application.
Two thermistors (NTC thermistors) connected in parallel protect against inrush current when the input filter capacitors charge. The previous power supply had just one—maybe they put in a spare here? :)
So far, so good.

48 V, 5 A and 240 W, or a power supply that managed to surprise me48 V, 5 A and 240 W, or a power supply that managed to surprise me

1. The input electrolytic capacitors are marked 680 µF 250 V and carry the name of the well-known Chinese company RubiconG, which apparently makes its products somewhere near Akaiwa and Abibas. Oh well, we'll measure them later, since the heat-shrink sleeve could be hiding anything. They look like someone chewed on them before installation. O_o.
2. The high-voltage transistors, in TO-247 packages, are clamped to the case with a plate and thermal pad. You can also see thermal paste, so there's nothing to complain about here.
3. The output diode surprised me twice in this power supply. Or rather, it wasn't the diode itself, but the way it was mounted.
This power supply's output current is only 5 A (the power dissipated by the diode is roughly the same as in a 5 V 7 A power supply), but they've even added an extra aluminum heatsink for it.
It's completely unnecessary here. I'll unscrew it; maybe it'll come in handy. The main thing is that the manufacturer doesn't find out, or they'll stop including it. :)
4. The output choke and capacitors. The choke looks a little small to me, and there's no output filter. But the tests will show what's what; maybe everything is fine.

48 V, 5 A and 240 W, or a power supply that managed to surprise me48 V, 5 A and 240 W, or a power supply that managed to surprise me

The second thing that surprised me was the output diode assembly. I understand that it doesn't dissipate as much heat as higher-current versions, but mounting it like this… Someone should be smacked for this—hard, because it really needs to be done.
It'll work, but not very reliably. And that's not even mentioning that thermal expansion and repeated heating and cooling could make the diode come right out of its mount.

48 V, 5 A and 240 W, or a power supply that managed to surprise me48 V, 5 A and 240 W, or a power supply that managed to surprise me

First test.
The output voltage was initially set to 48.7 V. The adjustment range covers 35 to 53 V; I then set it to the specified 48 V.
Interestingly, the 36 V power supply had exactly the same adjustment range.

48 V, 5 A and 240 W, or a power supply that managed to surprise me48 V, 5 A and 240 W, or a power supply that managed to surprise me

While measuring the output voltage, I smelled something hot (radio amateurs will know the smell). I immediately grabbed the pyrometer and started looking for the hot spot (I first tried the classic method) and found it.
There's a load resistor between the output filter capacitors, and it's getting hot.
The resistor is 1 kΩ, the same as in the 36 V power supply, but there it dissipates 1.3 W, while here it dissipates 2.3 W. Obviously, it's overheating. I recommend either replacing it with a 1.5 kΩ resistor or moving it a little farther from the capacitors; there's plenty of room.
But installing a little “land mine” like this is just ugly.

48 V, 5 A and 240 W, or a power supply that managed to surprise me48 V, 5 A and 240 W, or a power supply that managed to surprise me

After that, I took the power supply apart further. The board is held in place by one screw and the transistor and diode mounts, although there’s room for another mounting screw.
By the way, there are holes in the board opposite the mounting holes in the case itself. So if you decide to screw the unit to something, you don’t need to worry about screw length: screws up to 50 mm long will definitely fit.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

The circuit board gets a B. Soldering quality is average, and the traces carrying high current are tinned. Overall, it’s a standard board made of phenolic paper laminate, as in most devices like this.
There are no components on the underside.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

I didn’t draw a schematic for this one; I simply modified the schematic for the 36 V power supply.
The thing is, there are very few differences between these power supplies.
1. The fan power supply circuit was removed.
2. In the 36 V version, the thermistor was before the power filter; now it’s after the diode bridge.
3. Resistor R7 was removed (snubber circuit).
4. The value of resistor R41 was changed (it’s in series with the LED).
5. A different output diode assembly was installed.
6. The output inductor was changed.
What’s more, all the component designators on the circuit board are exactly the same as in the 36 V version. That’s convenient, but given that the board is “mirrored,” I think it was done deliberately.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

The high-voltage transistors are D13009K, just like in the previous power supply.
But the diode assembly is different this time: C25P40F, rated for a maximum current of 25 A and voltage up to 400 V. That’s plenty of headroom for a 5 A power supply.

As I mentioned above, this power supply doesn’t have a fan power supply circuit, but there’s room for one on the board. If needed, you can solder in the missing components and install a fan.
There’s also room for a second diode assembly in parallel with the first, but one is enough at these currents.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

During inspection, I found a marking on the board indicating that it was originally a board for (or from) a 300 W power supply.
Clearly, the boards are standardized and used across the entire range of power supplies with this power rating.
There is one small catch, though: a 5 V, 30 A power supply is not the same as a 30 V, 5 A power supply, even though they have the same power rating.
That’s because if the same inverter is used and its losses are the same, the output diode will dissipate much more heat at 30 A than at 5 A—even though the 5 V version uses Schottky diodes.
Sometimes manufacturers even rate the output current lower, listing, for example, a 150 W power supply as 30 V, 5 A and 5 V, 25 A.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

The power supply is built around the best-known PWM controller, the KA7500, better known by its original designation, TL494. There’s also a domestic equivalent of this chip; just about every manufacturer has made one :)

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

I'll tell you a little about PWM controllers in general, and the TL494 in particular.
First, it's worth noting that this PWM controller is very common. That's thanks to its simplicity, low cost, decent performance, and predictable behavior.
I first came across it about 17 years ago. At the time, it was a very good IC.
Of course, there are many PWM controllers now: low-voltage, high-voltage, multiphase, with and without an integrated power switch, and so on.

The IC comes in a 16-pin package. The pin functions are shown below.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

The IC's internal circuitry looks roughly like this. Actually, this is what it looks like in more detail; a simplified view will come later.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

To explain a little about what a PWM controller is—or rather, to show its main blocks—I drew this block diagram (I'm no artist, as you can see).
Let's start with the block numbers.
1. Power supply regulator. It's not shown in the main block diagram, but is sometimes present.
It powers all the internal blocks. Sometimes it has a low-power startup mode, which is useful for PWM controllers installed on the “high” side of a power supply. This mode first charges the IC's supply capacitor, then starts the IC, which is subsequently powered from a separate transformer winding (and sometimes without one).
2. Reference voltage source, or reference voltage generator.
This regulator maintains a highly accurate voltage. It serves as the reference point when measuring the input voltage.
With the TL494, this is the first thing to check (assuming the IC isn't shorted). In normal operation, it outputs 5 V. If the IC is powered but there's no voltage on this pin, the IC is faulty.
The reference voltage is also often used as the threshold voltage at the error amplifier input.
3. Oscillator. It may use external timing components or have them built in. With external components, the frequency can be set over a wide range; with an internal oscillator, the frequency is either fixed or selectable from 2–3 values. It sets the converter's operating frequency.
4. Error amplifiers. The TL494 has two: one is used to measure voltage, the other current. More often, though, there's just one error amplifier. That doesn't mean you can't regulate both current and voltage; you just need to add a couple of external circuits and combine their outputs at this input (as is done in many converters with constant-current and constant-voltage regulation). By the way, applying a voltage slightly above the reference voltage to this input can shut down the converter entirely. This can be handy when there's no dedicated enable/disable pin.
5. Dead-time control circuit. Some controllers let you adjust the pause between output signals—or, in other words, the maximum duty cycle. This can be necessary to protect the output transistors from failing, so one doesn't start turning on before the other has turned off.
This input is also often used for soft start by connecting a capacitor to it.
6. Control circuit. In simple terms, it synchronizes the oscillator and the error amplifiers.
The error amplifier's output voltage can change several times during a single cycle. To prevent “chatter,” the control circuit won't generate another control pulse until the next clock signal.
Here's how it works: the control circuit turns on the output transistor. When the voltage at the amplifier input exceeds the reference voltage, the control circuit turns the power transistor off and keeps it off until the next oscillator cycle. Then the process repeats.
That's the basic principle of PWM operation.
7. ICs that can operate in two-cycle mode (the TL494, for example) also have a flip-flop that drives the transistors alternately. That is, it processes the pulse width for one transistor, then the other, and so on.
The TL494 can also be switched to single-ended mode. In this mode, the flip-flop is disabled and the outputs operate in sync. This is needed for single-ended power supplies or DC-DC converters, such as step-down or step-up converters.
By the way, the transistors built into the TL494 can be used to make a low-power converter without external transistors. Their specs aren't great, of course, and there are plenty of ICs with powerful integrated transistors nowadays, but this was useful many years ago.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

Of course, the chip has been obsolete for a long time. Modern solutions are better and faster (they can operate at higher frequencies), support low-power startup, have built-in power transistors, can measure current, and so on.
But TL494 has been manufactured, is still being manufactured, and will continue to be manufactured—and this power supply is a clear example of why.
Of course, I'd like something more modern, but usually that means either a flyback power supply or a more expensive branded solution. In the budget segment, TL494 is still in charge.

I've reread what I wrote and realize it's not very well put together. Unfortunately, I'm not a teacher, and I don't have 1.5 hours for a lecture—just a short review, where I want to show the product, test it, and explain a little about how it works.
I still don't know how to fit the description into a small amount of text, but perhaps I'll add information as I publish new reviews (if they keep sending me products to tear apart), or maybe I'll put together a longer review. I'm not sure which would be better.
-----

At the end of the inspection, I measured the capacitance of the input and output electrolytic capacitors.
The input capacitor measured 448 µF, compared with the specified 680. Same story as with the 360 W power supply, but here this capacitance is perfectly acceptable, since the capacitors are connected in series, giving about 225 µF. For a 240 W unit, 240 µF is considered a good target. So there's no headroom, but it's not too low either.
The output capacitors are also unbranded: three 1000 µF, 63 V units.
No complaints about the capacitance or voltage rating: 3000 µF is perfectly fine for 5 A (a push-pull power supply needs less capacitance), and 63 V gives plenty of headroom. There's no point in using a higher voltage rating.

In the previous review, someone questioned the method I used to measure capacitors while they were soldered to the board. To avoid revisiting this issue, I also measured the capacitance of the desoldered capacitors. As you can see in the photo, there's no difference—or rather, any difference is within the measurement error.

48 V, 5 A and 240 W, or the power supply that managed to surprise me48 V, 5 A and 240 W, or the power supply that managed to surprise me

Before starting the tests, I took pity on it and made a small modification to the power supply (I feel sorry for the components—they're not to blame for the assembler being an idiot penny-pincher).
As I mentioned above, the output diode is clamped at an angle because of the wrong hold-down bar. It's probably designed for TO-220 components (the size of a standard 78xx regulator), while the TO-247 package is a little thicker, which is why it ended up tilted.
There are two ways to fix it.
1. Put a small piece of PCB material underneath.
2. Drill a hole in the case and secure the diode bridge with a screw.
As you can see in the photo, I chose the first option because it's the simplest.

48 V, 5 A and 240 W, or the power supply that managed to surprise me48 V, 5 A and 240 W, or the power supply that managed to surprise me

For testing the power supply, I set up the test bench many of you are already familiar with. It consists of:
1. Electronic load
2. Oscilloscope.
3. Multimeter
4. Non-contact thermometer
5. A power cable and wires for connecting the load.
6. A piece of paper and a very expensive, professional pen :))))

The electronic load drew the required current, turning all the power into heat (and noise); the multimeter measured the power supply's output voltage, the oscilloscope monitored ripple, the thermometer measured component temperatures, and the pen wrote it all down :)

48 V, 5 A and 240 W, or the power supply that managed to surprise me48 V, 5 A and 240 W, or the power supply that managed to surprise me

I won't comment on the main stages of the test; everything is clear from the photos and oscilloscope traces. I'll just say that the voltage stayed steady at 47.9 V throughout, and ripple never exceeded 25–30 mV.

1. No load
2. 1 A load.

48 V, 5 A and 240 W, or the power supply that managed to surprise me48 V, 5 A and 240 W, or the power supply that managed to surprise me

1. 2 A load
2. 3 A load

48 V, 5 A and 240 W, or the power supply that managed to surprise me48 V, 5 A and 240 W, or the power supply that managed to surprise me

1. Load at 4 A
2. Load at 5 A

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

Since the power supply behaved quite well (which surprised me a little; I expected worse), I continued testing.
1. Load at 6 A
2. After that, I increased the current in 0.5 A increments, so next was 6.5 A

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

But I didn't stop there, since the PSU kept stubbornly working, throwing off some of my plans and extending the test time.
1. I ran it for an additional 10 minutes at 7 A. The PSU kept working, although the ripple increased somewhat (to 50 mV), but it was still perfectly acceptable.
2. In the end, I couldn't resist and ran the PSU at 7.5 A, but it felt like it was just messing with me. The load started overheating (in the last photos you can see it running without its top cover), so I stopped the test.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

What can I say? The PSU passed the test with flying colors, which doesn't happen often.
And considering that it's not a brand-name unit, the output capacitors are unbranded, and the input capacitors look downright chewed up, I don't even know what to think.

Of course, the temperature measurements aren't entirely straightforward; there are a few caveats, but overall the results are good.
A few words about those caveats.
The results show that the output inductor overheated, but that's not what you need to worry about: it's not ferrite, and its maximum operating temperature is 200 degrees (and even then, that's the temperature limit of the coating, not the material itself).
Meanwhile, you don't want to let the transformer's ferrite core get above 100–110 degrees. At higher temperatures, its characteristics deteriorate sharply, and it effectively goes from a 100 W transformer to a 20 W one. The inverter then gets overloaded, followed by a bang and a trip to the store for new transistors.
My psychological limit for semiconductor temperatures is also around 100–110 degrees. They can operate at higher temperatures (up to 125, for sure), but reliability suffers.

And now, the table.
The test at 7 A lasted 10 minutes. Temperatures weren't measured at 7.5 A because that test was brief.
The total test time was 2 hours and 10 minutes.

48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me48 Volts, 5 Amps and 240 Watts, or a power supply that managed to surprise me

Summary
Pros
The power supply delivered more than its rated power
Operating temperatures are within the normal range
Excellent ripple levels
A proper input filter for 220 V
Excellent output voltage stability
Good short-circuit protection response.
Easy to repair

Cons
The input filter capacitors are of questionable origin
Poor-quality output capacitors
The output diode assembly mounting needs to be fixed.
The load resistor gets very hot and should be replaced.

My opinion: this time I'm torn. On the one hand, the input and output capacitors are of unknown origin, the output diode assembly isn't clamped down properly, and the resistor and inductor get hot. On the other hand, the test results showed a high overload capacity, very low ripple, and excellent output voltage stability, even at the maximum current.
On the plus side, it also withstands short circuits (I accidentally spent several minutes trying to start the PSU with its output shorted), the semiconductors have plenty of headroom, and the price is quite reasonable.

Would I buy this PSU? Yes. But I'd replace the output electrolytic capacitors with Samwha RD series ones, move the load resistor and output inductor farther away from them, check the diode assembly's mounting, and use it. With those modifications, I'd have a pretty decent PSU for a reasonable price.
An alternative would be to buy a Mean Well NES-series PSU, but here it costs 1.5 times as much, and that's a 150 W model, not a 240 W one.

I hope this information was useful and you enjoyed the review. As always, I look forward to your suggestions and questions in the comments.


The product was provided by the store for review.
$20.94
Go to store
This page was found when searching for:
8, бис-48/2ф1т характеристики, схема бис 482ф 1, можно ли светодиодный блок питания 36-48 вольт использовать для усилителя мощности, блоки питания базовых станций, https://www.kirich.blog/obzory/bloki-pitaniya/138-48-volt-5-amper-i-240-vatt-ili-blok-pitaniya-kotoryy-smog-udivit, подключение БИС-48/2Ф1, бис 48\2ф1, 48в 5а, БИС 48/2ф1 характеристики, источник бис 48/2ф1, блок питания 48 вольт на 36 вольт переделка, бис 48/2ф1 цена, переделка блока бис 48\2ф1, бис 48/2ф1т, 48 вольт, 5 ампер и 240 ватт, источники питания на корабле мц 1,5 ампер 48 вольт, усилитель на 48 вольт, блок питания c аккумулятором 48 вольт, нестабилизированный импульсный блок питания 48v 5a, 48в 5а 12в 20а, усилитель 48 вольт, бп 48в 5а, 48в 5а блок питания, система резервирование питания 240вт 48 вольт

Questions and answers

What is the adjustment range of the 48 V, 5 A power supply?

The output can be adjusted from 35 to 53 V; the author set it to 48 V.

Is the 48 V, 240 W power supply worth buying?

The author would buy it, but recommends replacing the output electrolytic capacitors, moving the resistor and inductor away from them, and checking the diode assembly mounting.

What can the 48 V, 5 A power supply be used for?

It can power loads such as LED strips, as well as a board for an adjustable converter.


This model is included in the summary table: Comparison of power supplies: ripple, efficiency, and temperature rise

The figures from this review are in the measurement database: Power supplies

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments2

Comments are published in their original language.

  1. evgeny
    8 August 2019 15:36#1
    Здравствуйте Андрей, Вас так зовут? Я приветствую Вас из далекой Сибири. Хоть статье скоро 4 года, но тема БП вечна, и у меня появилась пара вопросов. Схема этого БП очень похожа на комповый БП формата АТ, так как у меня несколько штук этих блоков, в том числе и формата АТХ, у меня чешутся руки изготовить самому БП как на 24В, 36В и 48В. Тем более, что цена описываемого блока перевалила за $30. Чтобы не перематывать силовые трансформаторы можно ли применить мостовую схему выходных выпрямителей? Почему-то везде применяют схемы со средней точкой обмотки, хотя расход меди больше, а наши желтолицые братья великие экономисты, но ведь диоды дешевле меди? И второй вопрос, можно ли низкочастотные диоды 1N4007 применять в базовых цепях ключевых транзисторов? VD14 & VD15 видимо UF4007, или тоже 1N4007? И последнее, не могли бы Вы пояснить обвязку 4 ножки TL494, С24 и R19 это софт-старт, а остальные детали? В частности не ясен тип стабилитрона ZD3. Спасибо! 
    +1
    1. 20 August 2019 02:28#2
      Да, если БП на 12 Вольт, то можно получить 24-28, если надо больше, то перематывать трансформатор.
      Вторичную обмотку с отводом применяют потому, что диодные сборки с общим анодом попадаются гораздо реже и потому проще делать. Кроме того иногда (в АТХ) надо и отрицательное напряжение.
      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister