RuiDeng RD6012P adjustable hybrid converter, the next model in the RD6006P series (not a review)
Today’s “not-quite-a-review” will be a brief announcement, a description of the new model and its differences, some real photos of the device, and, I hope, a discussion in the comments.
As usual, a reminder: to keep up with new posts on the blog, I recommend following me on Instagram. I’ll post notifications about every new article there, and maybe write about something interesting too — link to my account
I was first sent a link to Taobao, where new products usually appear earlier. It was available for preorder there, along with a note that the device was in the final debugging and bug-fixing stage. But this model soon appeared on AliExpress in several configurations:
1. RD6012P - $79.99
2. RD6012PW (with WiFi) - $83.99
3. RD6012P + enclosure - $111.49
4. RD6012PW (with WiFi) + enclosure - $115.49
5. Compatible 800 W power supply - $58.00
As you can see, the price isn’t much different from the 6006P, so in my opinion this model looks more interesting.
The catch is that these prices are valid only until 10.11.2021 (presumably inclusive); at least, that’s how I understood the announcement on the product page. After the sale, the 6012P is expected to cost $96, and the 6012PW around $100.

So the top configuration—the converter with WiFi, enclosure, and power supply—will cost $173.5. To get ahead of myself, I’ve already ordered the RD6012PW for review, and it’s been shipped. The product page already has a couple dozen orders, too.
Here’s a comparison table of all the models in the RD60xx series, with links to the reviews:
6006
6012
6018
6006P
By the way, I only noticed here that the minimum input voltage for the “P” series converters is 7 V, while it’s 6 V for the regular models. That makes sense, since a hybrid converter needs a little more headroom because of the voltage drop across its linear regulator.

The specified output current is up to 12 (12.1) A. Voltage can be set and measured with a resolution of 0.001 V, while current can be set and measured in two ranges, with resolutions of 0.0001 and 0.001 A.

The description explains that the 0.0001 A (0.1 mA) current resolution applies up to 6 A; above that, the resolution drops to 0.001 A (1 mA). It’s a fairly convenient solution, although in my opinion even 1 mA increments are more than enough for the vast majority of applications. Still, someone may find the higher resolution useful.

The buttons, control menu, operating modes, and so on don’t seem to differ from the 6006P, so I don’t see any point in going over them here.

The same goes for the software, although this converter may need to be updated to a newer version.

What’s more interesting is the internals—or, more precisely, the hardware. At a glance, it looks quite similar to the 6006P: the same heatsink and fan for the linear section, and the same heatsink for the switching converter. One key difference is a daughterboard mounted vertically on the main board. They’ve also fitted larger inductors, added capacitors, and installed 20 A fuses.
In simple terms, they took the 6006P and just beefed it up.

The layout is the same as in the 6006P: the linear regulator is on the left, and the switching converter is on the right.

Just to be safe, I asked the sales rep to send real photos of the device. Product-page photos are one thing—often they’re just renders—but an actual photo is another.

Judging by the date on the screen, the photo was taken specifically in response to my request, or at least it certainly looks that way. One thing I like about the RD series converters is their bright, high-contrast display. Compared with Atorch modules, it’s like night and day.

And of course, I asked for a real photo of the internals of a production unit. The assembly looks neat enough, although you can see that the board wasn’t cleaned after the connector joining the upper and lower sections was installed.
The layout is noticeably more compact, as you can tell from the fact that some components simply wouldn’t fit on the main board and were installed on the daughterboard.

They even put together a simple demonstration in the photo to show that the converter actually works and isn't just lighting up the screen. Well, they did their best :)

On closer inspection, though, this was initially a bit confusing: judging by the load current, the current measurement resolution should have been 0.0001 A, but the photo clearly shows 0.001 A.

It turned out to be very simple: the mode isn't automatic, but manual. According to the description, you switch between modes using the up/down buttons.
In other words, if you need higher resolution, select the 0–6 A mode and use it like the previous model. If you need more current, switch to the 0–12 mode. The resolution drops to 0.001 A, but the maximum load current doubles.
The product page has a bunch of links to videos, on Google Drive, though, and I still couldn't find a demonstration of switching between modes.

Of course, they left the option to update the firmware. To be honest, though, I don't update the firmware on my units—or even check what's in the updates—since I run them in standalone mode and I'm more than happy with how they work.

Although this is just an announcement, I'd guess that, judging by the tests of the 6006P version, we can expect roughly the same results. Essentially, it's the same 6006P, but with higher power and two operating modes: normal mode, with current up to 12 A and a resolution of 0.001 V/0.001 A, and "6006P emulation" mode, with current up to 6 A and a resolution of 0.001 V/0.0001 A.
I've been waiting for this converter model for a long time, because the 6006P really caught my interest. They sent me the 6012P for review, but if you'd asked whether I'd buy one, my answer would have been an unequivocal yes.
What's more, my first Meanwell EPP-500-54 power supply has already arrived. I bought it for the 6006P, and I've ordered a second one that will most likely be used with the 6012P. I won't be able to get the full power out of it, but I'll still be able to get up to 12 A, albeit at a lower output voltage.
That's all for now. What do you think of this model? Does it make sense or not?
ruideng ld35 кемерово, rd6012p, 6012pw
Questions and answers
How does the RuiDeng RD6012P differ from the RD6006P?
The RD6012P supports output current up to 12 A and has two current ranges: up to 6 A with 0.0001 A resolution and up to 12 A with 0.001 A resolution. The author also notes larger components and an added submodule on the board.
What is the current resolution of the RuiDeng RD6012P?
In the 0–6 A range, it is 0.0001 A; in the 0–12 A range, it is 0.001 A. The range is selected manually with the up and down buttons.
Which RuiDeng RD6012P versions are mentioned?
The article lists the RD6012P and the RD6012PW with Wi-Fi, each available with a case. It also mentions a compatible 800 W power supply.
The figures from this review are in the measurement database: Converters
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments7
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.