/       /       /    Mean Well SP-320-5 power supply, 5 V, 55 A
Support the project on Patreon


Mean Well SP-320-5 power supply, 5 V, 55 A

$58.50
Go to store
Another Mean Well for my collection, but today this isn't just a power supply review—it's a review of a used power supply. In my opinion, that's much more interesting and, most importantly, more useful than a review of a new one.


Actually, there are two power supplies, but testing both would take far too long, so I'll have to make do with just one.
One of my readers sent them to me, and I want to thank him not only for the power supplies themselves, but also for leaving them "as is." In a way, they've been through an aging test, and today I want to see how that has affected their performance.

I've included a link in the title just for the sake of having one, since the advantage of branded power supplies (and other products) is that they're the same everywhere, unless they're counterfeit, of course.


This power supply belongs to the SP-320-xx series, which includes models with power factor correction. The series has a huge number of output voltage options. There are the "standard" ones, meaning the common voltages—3.3, 5, 12, 15, 24, 36, and 48 V—as well as some less common ones: 7.5, 13.5, and 27 V. Only the 48 V model delivers the full power stated in its model number; for the others, it depends on the output voltage—the lower the voltage, the lower the maximum power.
I'll also note that, once again, 48 V is the limit for the output voltage. Mean Well models rated for 60, 72 V, and so on are almost never seen.


This is one of the lowest-voltage models, rated for 5 V and up to 55 A, so its power is just 275 W. Though "just" is relative, since these power supplies are often used to power LED displays, and there are... a lot of them in each display. The terminal block is in a slightly unusual position, with the screws facing the end of the case.


The case is the usual stamped aluminum design, with ventilation holes on the bottom.


And inside, of course, there's dust—a near-constant companion of devices with active cooling, especially those used in rooms with unfiltered air. Dust itself isn't all that harmful, but when combined with high humidity, that's when problems start: it can affect performance and reduce safety by potentially causing arcing in the high-voltage circuits.


The fans are fairly powerful, judging both by their current draw and by how much air they move. They are noisy, of course, especially when the power supply is under load.


It's pretty obvious these power supplies are used, and they clearly weren't operated in sterile conditions.


Of course, I'm not going to test them in this condition. I started by taking them apart; you can see dust even on the insulating sheets.


I just cleaned the fans, but the circuit boards took a bit more work. At first I thought I'd only clean them dry, but in the end I used a wet brush. I could have just put them in a tub of water or rinsed them under the shower, but I didn't dare.


In the end, I had two tidy circuit boards. Not perfect, but I got rid of most of the dust.


Unlike the LRS series, these boards have plenty of components on the top side. That's partly because these power supplies have been in production for a long time and use through-hole components; many components on the LRS series are on the underside of the board.


I've divided the power supply into its main functional sections here, since they're conveniently grouped together—well, except for the inverter itself, since the transformer and power switch are quite far apart. Incidentally, poor PCB routing here could add interference to the radio spectrum.


The input filter looks substantial, both in terms of the number of capacitors and the pair of inductors installed. A heatsink is installed on the bridge rectifier, even though the power supply itself isn't particularly powerful. The fuse isn't soldered to the board but sits in a holder. There are no varistors, though there is room for them.
The thermistor is tucked between the filter capacitor and the bridge rectifier.


The active power factor correction circuit. You can see its inductor, with the switching transistor and diode behind it. They're pressed against the power supply casing by a small aluminum heatsink, which also houses a thermal switch that protects the unit from overheating.


There are two filter capacitors, but unlike in a typical power supply, they're connected in parallel rather than in series. They're rated for 400 V and 150 µF each, giving a total of 300 µF.
The inverter transistor is next to them. This is a single-switch power supply, although of course there are single-switch designs with two transistors too—for example, a half-bridge topology, or simply two transistors connected in parallel.


The PWM controller section. You can see the chip itself and the feedback circuits. There are two optocouplers: one carries the feedback signal, while the other provides overvoltage protection by shutting down the controller.


The output rectifier, inductor and capacitors. Judging by the size of the output inductor, you can tell right away that this is a forward-converter power supply. The inductor is therefore an energy-storage element and must not be replaced with a jumper.


A pair of S60SC4M output diode assemblies, rated at 40 V and 60 A. There are three 4700 µF output capacitors.


1, 2. Y2-class capacitors are used in the “dangerous” spots; elsewhere, they're just high-voltage capacitors. In this case, though, that's perfectly safe, since they're effectively connected in series with the first ones.
3. Ferrite beads are often fitted over component leads.
4. There are beads on the “most important” Y capacitor too. To the left you can see the fan-control transistor's heatsink, and farther left, its temperature sensor.


Another important point was that the person who sent me these power supplies also included their schematic, which made my job much easier, since I usually draw it myself.



Before putting the boards back in the casing, I first cleaned off all the old thermal paste and applied fresh paste.


The output voltage was initially set a little high, with an adjustment range of 4.24–5.82 V. When I set it to the specified 5 V, I noticed that the adjustment was rather coarse, though in practice that's not a big deal at all.


First, I tested the power supply's load capacity and efficiency. For this I had to use two electronic loads: one rated for up to 30 A and the other for up to 40 A, giving me a test setup that could sustain a load of up to 70 A.
Power consumption with no load was about 8 W, which is quite a lot.


The power supply handled its rated 55 A without any problems.


It also handled 65 A just fine, but when I tried to raise the current a little further, it went into protection. The protection isn't latched, and the voltage recovered after a couple of seconds.

With no load, the output was 5.017 V, then it dropped linearly to 4.982 V at 65 A.


Power supply efficiency.
Efficiency averaged around 80%. It reached that level at 20 A, then started to drop above 55 A. On the graph's horizontal axis, 1 = 5 A of load.
The power factor was 0.8–0.9 up to the load current, then rose to 0.97 and stayed there up to the maximum output current of 65 A.


The oscilloscope traces, like the voltage measurements, were taken from an unused pair of contacts on the output terminal block.


Ripple—an especially interesting test for used power supplies. The manufacturer specifies no more than 150 mV peak-to-peak; in reality, I measured even less.
Four oscilloscope traces: no load, then at 20, 40 and 60 A. The last one was taken under overload, and even then the ripple came in under 100 mV. In my opinion, that's excellent.


Low-frequency ripple only showed up at 60 A, and even then I wouldn't call it large, especially for a used power supply.


Thermal test. I cut this test a little short, since the electronic loads were having a rough time. In the end, I ran two 20-minute tests at currents of 30 and 60 A.


I measured the temperatures while the tests were running, which added a bit of excitement: removing the cover wasn't exactly convenient, and I was afraid of shorting something out.
After 20 minutes at 30 A, everything was fine. The only unusual thing I noticed was a brighter spot around the power factor correction circuit. The aluminum heatsink shouldn't have been visible in this measurement mode, so perhaps it simply emits infrared radiation well in that spot, though it looked no different to the naked eye.


Another 20 minutes at 60 A didn't change much either. The hottest components were the output diodes; the transformer only reached 75 degrees. The last photo shows the terminals and wires, which had heated up noticeably.


The final test was run alongside the thermal soak to check how the output voltage drifted as the unit warmed up.
1. No load, power supply cold
2. Start of the 30 A test
3. After 20 minutes
4. Start of the 60 A test
5. After 20 minutes
6. No load, power supply hot.

The voltage changed by just 12 mV after warming up!


And now for the verdict.
I think the power supply performed excellently. Keep in mind, though, that it's not new, so it could easily have failed one of the tests—and yet even the ripple results were excellent.

As for its intended use, it's a good power supply, but not particularly suitable for home use. The power factor correction circuit makes it about twice as expensive as comparable units in the newer LRS series, which are rated for 60 A rather than 55 A at the same stated power.

So if you need a charger for modern smartphones, this probably isn't the one to get :) Just out of curiosity, I worked out how long it would take to charge a typical smartphone with a 4000 mAh battery (if that were technically possible) from this power supply. A full charge would take just over four minutes—now that's Quick charge :)

That's all from me. I hope this was useful, and thanks again to my namesake for such lovely gifts :)
$58.50
Go to store
This page was found when searching for:
rsp- 2000a-r18 электросхема, sp-750-12 mean well schematic, электрическая схема блока питания lrs-50-r11, mean well pb-1000-24 схема принципиальная, схема электрическая принципиальная nsp-320-12, sp-300-5 переделка на 12в, ts-77-248b схема mean well, s-320n-r19vai, sp-500b-r12 схема, sp-320-5 схема, https://www.kirich.blog/obzory/bloki-pitaniya/833-blok-pitaniya-meanwell-sp-320-5-5-volt-55-amper, sp-320-5 схема mean well, блок питания sp-320-36 схема, sp 320-5 блок питания, 8, mw s-320n-r16vai diagram schematic, схема блока питания sp-500-27, схема блока питания s-320-27 на 27 вольт, схема блока питания mean well, схема sp-320-5, sp-320-24 модернизация, блоки питания серии sp схема и описание, mean well 5v схема, mean well sp 300 24 не включается, mean well sp 320 24 ремонт

Questions and answers

What load did the used MeanWell SP-320-5 withstand?

It handled its rated 55 A and 65 A without problems. When the current was raised further, the unit entered protection and the output recovered after a couple of seconds.

How hot does the MeanWell SP-320-5 get at 60 A?

After 20 minutes at 60 A, the transformer reached 75 °C, and the output diodes were the hottest components. After warm-up, the output voltage changed by just 12 mV.

Is the MeanWell SP-320-5 suitable for home use?

The author considers it a good power supply, but not an ideal choice for home use: its power factor correction makes it about twice as expensive as comparable units in the newer LRS series.

The figures from this review are in the measurement database: Power supplies

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments9

Comments are published in their original language.

  1. 18 January 2020 03:47#1
     Раз БП б/у, то как раз можно посмотреть, как сказывается работа БП и такие условия на фирменных конденсаторах.
    Проверить один конденсатор 150uF/400V, один с выхода 4700uF/10V и конденсатор по питанию микросхемы.
    0
    1. 18 January 2020 04:52#2
      Здесь есть две сложности.
      Первая, несущественная.  блок опять придется разбирать.
      Вторая, такой тест смысла не имеет так как неизвестны изначальные параметры, т.е. не поймешь степень старения. Мало того, даже если бы один Бп лежал на полке, а второй работал, то даже это не дало бы информацию, так как компоненты имеют свойство стареть даже так.
      Вот если бы взять блок, измерить параметры, потом пару лет погонять в максимальных режимах, а потом измерить еще раз и сравнить, то да, это имело бы смысл.
      0
      1. 18 January 2020 05:22#3
        Про неизвестность изначальных параметров конденсаторов, для сравнения, это понятно.
        Имел в виду явное /критическое снижение параметров.
        0
        1. 19 January 2020 20:36#4
          Так в том-то и дело, что здесь его нет, т.е. компоненты если и ушли от исходных, то не так уж и далеко иначе блок не выдал бы нормально показанные выше результаты.
          На мой взгляд то что он даже при 60А имел не очень большой размах пульсаций говорит о многом, в том числе и о качестве компонентов.
          0
  2. 9 August 2020 07:35#5
    Цитата: kirich
    неизвестны изначальные параметры

    А ДШ на что? Кстати, интересный сайтик - http://www.paullinebarger.net/DS/

    0
  3. 23 May 2022 10:39#6
    Добрый день. Хотел спросить а вы разобрались как работает обратная связь, зачем две оптопары?
    0
    1. 23 May 2022 11:30#7
      Я и не разбирался, там как и у других минвелов, на втором оптроне реализована защита от превышения напряжения на выходе в случае отказа основной цепи обратной связи.
      0
  4. 24 May 2022 16:55#8
    Очень похоже, спасибо. Собираюсь его переделывать так и чувствовал нужно его выкинуть)


    0
    1. 26 May 2022 10:31#9
      Я бы не выкидывал, функция довольно полезная, если хочется немного поднять напряжение и срабатывает защита, то просто скорретировал бы порог.
      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister