ANENG AL01: Review of an Inexpensive Multimeter That Can Measure Inductance
A reminder: to keep up with new posts on the blog, I recommend following me on Instagram, where I'll post notifications about new articles and maybe write about something interesting too — link to my account
You can also subscribe to updates and new articles on the Telegram channel — https://t.me/KirichBlog
I already have plenty of measuring instruments, so I bought this multimeter solely for the review. I don't know what I'll do with it afterward; maybe I'll put it up for sale. But first, I recommend reading the review.
While the package was still in transit, I noticed that it seemed to weigh very little. Sure enough, I received a small, lightweight box, but it was quite neat. There’s a sticker on the back with the manufacturer's details and other information—very official-looking.

Inside were the probes, a temperature sensor, a manual, and the meter in a nice little case.

I'd call the probes child-sized. Seriously, they're small and have thin wires. They're supposedly rated up to CAT II 600 V, which seems very optimistic to me.
The maximum current is 10 A. Out of curiosity, I estimated the wire cross-section: at a length of about 70–75 cm, the resistance is 25 mΩ, or roughly 35 mΩ per meter, which works out to a cross-section of around 0.5 mm². I expected it to be smaller. They'll do for short tests, even at 10 A, but for continuous use, it's best not to exceed 5–7 A.
The temperature sensor is completely standard—not even worth discussing.

The package also included a basic manual, nothing unusual there either.

For the specifications, it's best to check the product page itself.

The multimeter, the case—everything is so cute :)

The exterior is completely familiar: no touchscreens or flashy bells and whistles, just a regular multimeter.
The only thing that immediately caught my eye and felt unusual was the jack for measuring low currents, which is shared with all the other measurements. In other words, the third jack (the first one in the photo) is only for measuring current up to 10 A. Maybe this is fashionable now; I don't really keep up with current trends, but I hadn't seen it before. And there are pros and cons to this design, roughly 50/50.

Description of the controls and display from the product page
.

There’s a kickstand on the back that locks in place when deployed. No complaints there. The battery compartment cover is held by a latch on one side and a small screw on the other. The screw isn't captive, and the cover itself has a strange design. Apparently, it was originally meant to lift up, but I ended up accidentally pulling the whole assembly out :)
On the plus side, it runs on two AAA batteries, though the compartment seems designed for slightly longer ones.

It stands fine like this, but there are a couple of caveats:
1. The multimeter is very light, so it'll slide around as you pull on the leads, especially if you use thicker ones.
2. There are two control buttons, and they'd be fine if the multimeter's case weren't shaped like a bar of soap. You can't just press a button with one finger without the meter tipping over, so you have to hold it in place. This is made worse by the fact that some positions on the mode selector include a lot of functions, but we'll get back to that.

The case is held together by four self-tapping screws, but the two halves also fit together tightly, so I literally had to pull the internals out.

When I opened it up, I was surprised by how empty it was inside. There's almost nothing in here.

But there are fuses on both inputs. They're small, but they're there: 600 mA and 10 A. At least that's something in terms of safety. A fairly thick shunt is also visible on the right, which is good.

The voltage-divider resistors are on the left, and the bridge rectifier and protection diode are on the right. It looks simple, but neat.

And here are the “brains.” Everything is very straightforward here too. I didn't remove the boards, but I assume there's nothing on the other side except the switch and display.

I found a datasheet for this chip online, and got the impression that it's not a dedicated ADC of the kind used in multimeters, but something more general-purpose, like a microcontroller with a large number of different inputs and outputs, designed in part for applications like this.

The display with all segments lit, showing every possible symbol

The display is easy to read from the front, side, and below. The characters are fairly large and clear, but they fade immediately when viewed from above. It's less pronounced in person than in the photo, but still hard to read.

It has a backlight, which turns on when you press and hold the blue button. I didn't check whether it can be turned off. The multimeter itself shuts down after about 15 minutes: first it beeps a few times, then pauses, gives one long beep, and turns off.

All the modes, with the selector positions highlighted in color. Speaking of the selector, it's a bit odd. It feels like there are distinct intermediate positions between some of the modes. What's more, if you set it to one of these intermediate positions, the multimeter starts beeping in some cases.

My first test is usually a little unusual. Here, I first measure the voltage at the terminals in resistance, diode-test, and continuity modes, then measure the current in those same modes.
Why do this? For resistance measurements, a lower voltage is better, while for diode testing, a higher voltage is preferable, so you can test white LEDs too. This meter does fine on both counts.
I also liked the continuity buzzer. It's not as fast and “scratchy” as the old 830 and 890 models, but it's quite crisp and responsive. My only complaint is the coating on the probe contacts: sometimes it didn't beep right away. But when I touched the probes to a circuit board, everything worked clearly. Overall, no complaints here.

I'll test it either against components with relatively high accuracy or by comparing it with my main meter, UT181A. Of course, the ANENG AL01 looks a little funny next to my Uni-T :)

A quick check of DC voltage accuracy. I didn't look too closely—it's hard to mess this up. I just probed the reference voltage source, and it looks fine to me.

Next I tested current measurement. I used an RD6006P as the source at first, then switched to an RD6012P for currents above 6 A. I set the current on those supplies to 1, 2, 5, 10, 20, 50, 100, 200, and 500 mA, then 1, 2, and 5 A. The meter I trust is on the right for comparison.
No complaints, really.

When I applied 10 A, it turned out that the little ANENG AL01 also beeps on overload, even if it's only a slight overload. That's actually a handy feature, and I'm all for it.

A quick check of resistance measurement accuracy: first a 75 Ω, 1% resistor, then 510 Ω, 2.47 kΩ, 180 kΩ, 0.25%, and 412 kΩ, 1%.
Looks fine here too.

Capacitance measurements, again mostly using fairly accurate capacitors. Interestingly, it showed zero with just the probes connected. I have to zero the readings on my meter, so perhaps this one has some kind of automatic zeroing. That's the first photo.
Capacitors: 1000, 1800, and 7850 pF; 0.1 and 0.39025 µF non-polarized; and 100, 1000, and 22000 µF polarized. At first, it seemed like the 1000 µF electrolytic capacitor was taking a long time to measure, but the 22000 µF one measured quickly. Maybe it just seemed that way.
No complaints here either.

I checked the frequency measurement accuracy and range using a square wave at the input. I was surprised that with the probes connected and the output turned off, it showed the mains frequency. The input is clearly quite sensitive.

Up to 60 kHz, no problem—it's accurate. Go higher, though, and it starts showing complete nonsense at 70 kHz.

I checked the manual and saw that it should measure up to 60 MHz. I thought 8 V peak-to-peak might not be enough in the upper voltage-measurement range, so I switched the multimeter to the mV range and applied the same signal. But it turned out to be too much for it there: at 100 kHz, the battery symbol lit up and the whole display backlight came on. If I raised the frequency to 300–500 kHz, the multimeter simply shut off.
So, in the mV range, I applied a square wave with a 2 V peak-to-peak amplitude and was able to test up to 20 MHz. My signal generator won't go any higher. I could have switched to a sine wave, which goes up to 60 MHz, but I just didn't see the point.

This is a more interesting test. I applied the same square wave to the multimeters' inputs and wanted to compare the ANENG AL01 with my main meter, which uses a dedicated chip for True RMS measurements.
Measurements were taken at 50, 100, and 500 Hz, and at 1, 2, 5, 10, 20, and 50 kHz.
Up to 2 kHz, everything is basically fine. Above that, it starts under-reading, and above 20 kHz it starts showing nonsense.

Just out of curiosity, I compared it at 100 and 200 kHz. Well, what can I say—good thing not many people need this :)

We've gradually arrived at this meter's main feature: inductance measurement. The manufacturer even gave it a dedicated switch position, which I think is completely wrong, because that leaves some of the other positions overloaded.
For example, frequency, capacitance, and temperature could all share one position, which would immediately free up the others. Especially since frequency, capacitance, and temperature are measured much less often than voltage, resistance, and current. And besides, remember how I said the multimeter has a soap-bar-shaped case and the buttons are awkward to press? Put those two things together and you get a hit to ergonomics: you'll have to switch modes a lot, and it's not very convenient.
For the test, I gathered a bunch of different inductors, plus a transformer and a relay, which also has a coil.

I'll compare it with my main meter. I also have a DIY one, I think from the ProRadio website, and a few transistor testers that can do this too. But for now, the XJW01 is the most accurate of them.
So, I won't repeat the information shown in the photo; you can see it all in the XJW01 readings. I'll just point out the main—and disappointing—limitation: it only starts measuring reasonably well at 330 µH, and it can't detect anything at all down to at least 37 µH. Above 330 µH, it measures reasonably well, though I did find one oddity: the two-winding choke almost at the bottom on the right. The multimeter stubbornly read 4.491 mH, while my meter read 6.442 mH. I don't know why; it may have something to do with the measurement frequency and the choke itself, though this hasn't happened with the others.

So what disappointed me about the inductance measurement? The lower measurement limit. 330 µH is a LOT. For comparison, I calibrated my DIY meter using a 100 µH choke, and as you can imagine, I wouldn't use something near the bottom of the range for calibration, so its lower limit is much lower. Sure, I didn't expect the multimeter to show anything down to around 5 µH, but 330 is just way too high. Even a beginner radio hobbyist is likely to have plenty of chokes with significantly lower inductance.
And yes, I tried connecting an inductor without using the probes. I used a 22 µH one with long leads. When connected, it cycles through the ranges and then still reads 0.
By the way, when I first saw this multimeter, I laughed at the main photo. Not only are the alligator clips connected to insulated wires, but it's also measuring the inductance of a choke in a setup where, strictly speaking, it can't have any inductance :) But it's a nice photo, no doubt about that :)

I paid 8.83 in the coins section.

So, what do we have in the end? In principle, the multimeter itself is pretty good: small, fairly accurate, inexpensive, lightweight—I’d even call it pocket-sized. It has lots of different modes, TrueRMS, NCV (not tested), current measurement up to 10 A, frequency measurement up to 60 MHz, and a 6000-count display. All in all, there doesn’t seem to be much to complain about, and for the price it’s actually quite good, especially when it’s on sale (add it to your cart and you can get a good discount in the coins section).
But then there’s the fail with its main advertised feature... No, the feature works; it’s hard to argue with that. But the measurement range is clearly too limited, especially at the low end. Modern DC-DC converters use inductors around 5–10–100 µH, and the multimeter simply can’t even detect them. That’s a shame.
There’s only one thing that makes up for this shortcoming: this feature is extremely rare in multimeters, and its availability doesn’t really depend on the price. For example, it’s missing both from my Uni-T and from the expensive Fluke 287.
And as I mentioned, because the manufacturer wanted to promote the new feature, they crammed too much into the other ranges. In particular, the low-voltage measurement position and the one next to it, which combines resistance and capacitance measurement, diode testing, and the continuity buzzer.
Yes, my Uni-T has the same issue, and it’s even worse there. But that’s justified by the much larger number of functions it has in the first place. Besides, it sits on my desk in a way that means you can’t possibly flip it over by pressing buttons :)
In short, it’s an interesting instrument in its own way, and I think it could be quite useful for a beginner or a hobbyist who isn’t too demanding. I liked it overall.
That’s all for today. I hope you found this useful, and as always, I’d be very glad to hear your comments.
8, 2, https://www.kirich.blog/obzory/izmeritelnoe/1255-aneng-al01-obzor-nedorogogo-multimetra-s-vozmozhnostyu-izmereniya-induktivnosti, 1, aneng al01
Questions and answers
Can the ANENG AL01 measure small inductors?
The author found that it does not detect inductors around 5–10–100 uH. Its lower inductance limit is therefore too high for these components.
What features does the ANENG AL01 offer?
It has TrueRMS, a 6000-count display, current measurement up to 10 A, and frequency measurement up to 60 MHz. The author also liked its continuity buzzer and found its accuracy generally good.
Is the ANENG AL01 suitable for a beginner?
The author thinks it could suit a beginner or a hobbyist with modest requirements. However, inductance measurement is limited at the low end, and the supplied leads are better suited to brief 10 A tests; the author recommends staying below 5–7 A for extended measurements.
This model is included in the summary table: Comparison of measuring instruments reviewed on the blog
The figures from this review are in the measurement database: Measuring instruments
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments5
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.