/       /       /    KSD-01F thermal switch in a TO-220 package
Support the project on Patreon


KSD-01F thermal switch in a TO-220 package

¥3.00 ($0.44)
Go to store
When I ordered a multichannel battery tester, I also picked up a dozen thermal switches from the same store, ZKEtech. I needed them to control the cooling fans in my high-power electronic loads and power supplies. I meant to review them right away, but then forgot about it, so today I decided to make up for that.


I’d been meaning to order some thermal switches like these for a while. They’re available in local stores, but usually cost about twice as much. Here, with the electronic load in the same order, the small extra weight was barely noticeable, so they effectively cost the 0.44 dollars per piece mentioned above. They’re available on AliExpress too, but they’re usually not cheap there either. I did find a listing with free shipping and a price of 0.5 dollars, but shipping is free only for orders of fewer than 5 pieces; after that, you have to pay extra or split up the order.

They came in a regular zip-lock bag, and all 10 were there.


But as it turned out, there are some differences, at least in the markings (that’s what I thought at first). Three of the ten have slightly smaller lettering, and the markings are positioned lower.


Before getting to the main part of the review, a few words about thermal switches in general.
To start with, there are many types. Don’t confuse them with thermal cutoffs, which are single-use devices. Thermal switches—or, more precisely, thermostatic relays—are designed to switch on and off repeatedly.

They come in various designs. Here are some of the most common types:
1. KSD-301: a large, round housing, secured with a pair of screws. It has mounting tabs either on the housing itself or on a separate clamping washer. Rated for currents up to 10 A.
2. KSD-9700: a narrow, elongated metal housing. There’s also a version with a plastic housing; it’s held in place with a special plate. Rated for currents up to 5 A.
3. KSD-01: a TO-220 package, secured through a hole in the flange. Rated for currents up to 1.5–2 A.

There are also:
KSD-10, in a round housing.
KSD-2, a smaller rectangular plastic housing.
KSD-6, similar to the KSD-301.

For more details, see here.


Thermal relays also come in two types: normally open and normally closed. When they overheat, the normally open type closes the circuit, while the normally closed type opens it.


The markings usually include the model name (JUK-31F in the example below), the temperature in degrees Celsius, and the type (NO or NC).


The thermal relays in this review come in the familiar TO-220 package, well known to many electronics hobbyists.
Specifications from the datasheet:
1. Contact type: 1 NO or 1 NC.
2. Contact rating: 220 VAC, 1.5 A or 24 VDC, 1.5 A.
3. Insulation resistance: ≥50 MΩ.
4. Contact resistance when closed: ≤100 mΩ.
5. Breakdown voltage: ≥500 VAC; off-state gap: 0.35 mm (presumably).
6. Weight: < 2 g.

For anyone unfamiliar with TO-220, here’s an example using a standard 7805 voltage regulator. The thermal relay’s flange is a little thinner than a transistor’s, but thicker than those on the newfangled “economy” versions of voltage regulators.


As I mentioned, the thermal relays differ in the lettering on their markings, but it turns out there are many more differences. To make things clearer, I’ll refer to them as the small-font and large-font relays.
1. The small-font relays have some kind of epoxy-like compound protruding near the flange.
2. The flange itself also has a different shape. The small-font relay is on the left.


By the way, on closer inspection I noticed small gaps between the corners of the flange and the housing. That makes sense, really: this is a mechanical component, so unlike a transistor, the housing isn’t filled with compound—it’s just a cover.


I decided to start the tests by checking the contact resistance. As a reminder, the specified value is less than 100 mΩ.
In practice, it was noticeably better, but I also found another difference in how the small-font and large-font relays behaved.
The small-font relays (top) had higher contact resistance, and it also varied slightly with temperature. For example, we heat the relay until it switches, then remove the heat: the resistance is 18 mΩ and gradually drops to 11–13 mΩ, but then starts rising again as it cools.
The large-font relays usually had lower resistance, although one had a higher value. However, I didn't observe resistance fluctuations as pronounced as with the previous ones.


Perhaps the only thing they have in common is that the contact group is electrically isolated from the flange.


For the next tests, I wanted to take one relay and check its switching temperature and hysteresis (the difference between the switching-on and switching-off temperatures). To do this, I attached the thermal switch and a high-power diode to a heatsink; the diode served as a heater.
The thermal inertia turned out to be high, which made it much easier to take readings, but it took longer than heating the thermal switch with a heat gun or soldering iron.


As a reference, I used a table showing the switching-on and switching-off temperatures. Sorry for the poor quality; this was the best I could find.
For the 50-degree relay, the specified switching-on temperature is 50 +/-5 and the switching-off temperature is 35 +/-5. In other words, it switches on at 45–55 and switches off at 30–40.



I picked a thermal switch at random for the first test, and it turned out to be one with large lettering.
Since I didn't know which temperature was better to monitor—the relay body or the heatsink next to it—I measured both. The results were:
Switching on: 49.6/52.2; switching off: 31.2/32.8; hysteresis (based on the average temperatures): 18.9 degrees.


I could have stopped testing there, but somehow most of my reviews end up turning into investigations, and this one was no exception. So I decided to run a second test, checking a relay with small lettering, then another one, and another...
Here are the results:
1–4. Relay with small lettering — switching on: 42.3/46.6; switching off: 35.8/37.6; hysteresis (based on the average temperatures): 7.8 degrees.
5–8. Relay with small lettering — switching on: 43.2/46.3; switching off: 33.6/34.5; hysteresis (based on the average temperatures): 10.7 degrees.

This seemed odd: both relays with small lettering had lower switching temperatures. To double-check, I tested another relay with large lettering.
9–12. Relay with large lettering — switching on: 47.6/53.1; switching off: 27.8/28.7; hysteresis (based on the average temperatures): 22.1 degrees.


It turned out that the relays with small lettering have an average switching temperature of 45 degrees, while the ones with large lettering average 50 degrees. The last relay had an absolutely enormous hysteresis: it switched off at 28 degrees. It gets that warm in my house in summer... There is one small caveat, though: these relays are mechanical devices, so vibration can affect the switch-off temperature. For example, if a fan is running next to the relay, it will probably switch off a little earlier.

Here are the four test subjects, in the same order as in the test.


The strangest thing is that I bought them from a manufacturer of electronic loads, which apparently uses these exact relays in its devices. And they work perfectly well in the electronic loads. Below are photos of thermal switches installed in four different electronic loads.


Conclusions.
The relays themselves are very convenient, they work, and the price was right. But I got the impression that the three units with small lettering are rated for 45 degrees, not 50 as specified. At least, that's what the tests showed, and the ZKEtech electronic loads use relays with small lettering.

Even so, I have to say I really liked these thermal switches, primarily because of their convenient housing. You can install one on the circuit board next to the power transistors and avoid messing around with wires. By the way, I once learned the hard way with larger thermal switches (like the KSD0301): it turned out that one of their two terminals couldn't be soldered at all. I checked several thermal switches, and it seems the terminals themselves are made of different metals.

That's all from me. I hope you found it useful.
¥3.00 ($0.44)
Go to store
This page was found when searching for:
kds01f характеристики, ksd1 что это, ksd f 0,1 термореле, ksd-01f d 75 h3, ksd-01f а характеристик, датчик ksd 01 f защита усилителя принцип работы, ksd-01f характеристики и применение, kso-01f, ksd-f01, 2, Термостат KSD-01F H40°C (40°C, нормально-разомкнутый), 01f, термостат ksd-01f характеристики, термовыключатели ksd характеристики, назначение, 6, гистерезис ksd-01f, ksd-01f а, датчик с проводом термореле защиты от перегрева воды на выходе, термовыключатель защита 5а, термореле 12 вольт, ksd1 90/80, https://www.kirich.blog/obzory/radiolyubitelskoe/926-termorele-ksd-01f-v-korpuse-to-220, ksd -01f, резистор KSD 1 Y03 90/80, ksd-01f d60 характеристики

Questions and answers

What current is the KSD-01F thermal switch rated for?

The datasheet specifies 1.5 A at 220 VAC or 24 VDC.

At what temperature does the KSD-01F switch operate?

The tested large-print unit switched on at 49.6/52.2 °C, while small-print units averaged about 45 °C. The author found that the marking variants differed in their switching temperatures.

What hysteresis did the KSD-01F thermal switches show?

The first tested unit had an average hysteresis of 18.9 °C. Small-print units measured 7.8 and 10.7 °C, while one large-print unit measured 22.1 °C.

The figures from this review are in the measurement database: Other devices


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister