Features of backup power, or what to do during rolling blackouts, Part 3: Batteries
Today I’d like to talk about the features of different types of batteries, particularly how they’re used in UPS units and for long-term off-grid power in general. I’ll try to explain the differences between battery types, what to consider when using them in different situations, and some charging-related details.
As usual, a reminder: to keep up with new posts on the blog, I recommend following me on Instagram. I’ll post notifications about every new topic there, and might also write about something interesting from time to time — link to my account
So, let me start by saying that I don’t sell batteries, and until recently I hardly used them at home because I simply had no need to. But I’ve been involved with this subject before, and more than a hundred different batteries have passed through my hands during testing, so I’ve built up a bit of experience to draw on. The point is that batteries are often used incorrectly. At best, they simply work inefficiently; at worst, they can degrade relatively quickly. You can see an example of rapid degradation in this cycle-life test, where an incorrect charging profile killed the battery in just over a hundred cycles. Follow safe operating guidelines, though, and even a Chinese battery can last a long time, as shown in this cycle-life test.
I should also mention that I’ll cover the types of batteries you can actually find on the market. There’s no point writing about exotic types such as silver-zinc or nickel-hydrogen batteries, and so on.
First up, of course, are lead-acid batteries. You could sum them up in a few words: cheap and cheerful.
Yes, they’re readily available and inexpensive, but that’s about where the advantages end and the drawbacks begin, especially with the most common type, starter batteries:
1. Discharge current. You’ll see impressive figures like 250, 300, or 500 A, but forget about them. For starter batteries, those are only short-term current ratings. For sustained use without damage, they can deliver no more than 0.1–0.15C, where C is the battery capacity in Ah. So, for a typical 60 Ah battery, the continuous discharge current is only 6–10 A, or 70–120 W of power, not counting inverter losses.
2. Float charging. Ordinary lead-acid batteries don’t handle it very well. And if you use them in cyclic operation, they lose their charge relatively quickly during downtime due to self-discharge.
3. Charging current. Some might say, “What difference does it make? I can charge it whenever it suits me.” No—you can charge it when you have the opportunity, and not just any way you like, but at only 0.1–0.15C. That means a full charge (and what else would you need after a prolonged outage?) will take 7 to 12 hours. Will the battery have time to recharge between outages? Not necessarily.
4. Short service life. Yes, the low price comes at a cost: these batteries are unlikely to last for years. I’d plan on a year to a year and a half at most. But if you only need one for a relatively short time rather than for years of use, a lead-acid battery may be just the thing: use it, then recycle it.
By the way, I have a short review of a gel battery for a UPS, where you can see how the energy it delivers drops as the load current increases.
Here’s how you can address the problems listed above, or at least mitigate them.
You can compensate for the low discharge current by increasing the capacity. For example, a 120 Ah battery can deliver 12–20 A, or 150–250 W, which is much better. And there’s nothing stopping you from increasing the capacity even further—the discharge current will rise proportionally.
You can also use traction batteries. They’re designed for high discharge currents over extended periods, but they cost more and are less widely available.
Unfortunately, there’s no way around the low charging current: either accept faster aging or put up with a 7–12-hour charge.

Gel batteries are a type of lead-acid battery. The key difference is that their electrolyte is thick, so the battery can be installed in any position. Well, perhaps it’s best not to install it with the terminals facing down, although that is technically allowed too.
You’ve probably seen them in computer UPS units (and other types as well), but they’re also available in higher capacities. These batteries may last longer than conventional ones, though that depends heavily on the manufacturer.

But you need to be careful with batteries like these. First, it’s best to buy products from well-known brands, such as CSB or Yuasa.
Also, batteries like these can differ even within the same form factor. I’ll skip the obvious counterfeits with glass instead of proper internals, but I’ll explain the technical differences. Batteries with capacities of 7–9 Ah—the kind commonly used in computer UPS units—are also often used in other UPS units, such as those for alarm systems. The difference is in the current they can deliver. So you buy one of these inexpensive batteries, install it in your computer UPS, and a year later you suddenly find out that it’s dead. You can usually tell them apart by the price, so if you're installing them in a device that may draw a lot of current, use only branded batteries specifically designed for that kind of operation. The difference isn't just the price!

Next are the equally well-known nickel batteries, which have been in use for a long time and come in various types, such as nickel-cadmium and nickel-metal hydride.
You've probably seen batteries like these in cordless phones, toys, and power tools. But they are also made in much higher capacities and have long been used in uninterruptible power supply systems.
In my opinion, they have more advantages than lead-acid batteries, though of course they have their drawbacks too.
Their advantages include no need for balancing—this happens "automatically" during charging—and better tolerance of over-discharge. Lead-acid batteries are more "delicate" in this respect. They are electrically compatible with lead-acid batteries (10 nickel cells have the same voltage as a 12 V lead-acid battery), last longer than lead-acid batteries, and can deliver current continuously at 0.5–1C.
The drawbacks are a higher price, much lower availability, the "memory effect," and relatively high self-discharge.

Besides those mentioned above, nickel-iron batteries are also used. Many years ago, during the previous round of rolling blackouts, I once bought ten TNZh-450 batteries. They were dry, but in the end I never filled them with electrolyte and later sold them as they were. A battery like that has a capacity of 450 Ah, or about 4500 Wh, which is pretty good even by today's standards.
Batteries like these are still relevant and still being made, but are gradually being replaced by lithium batteries. You can still come across large battery banks, for example in telephone exchanges, electric vehicles, and so on.

Lithium batteries are the fastest-developing battery type, and they too have both advantages and drawbacks.
Broadly speaking, they can be divided into three types. I'll start with the first, which we can loosely call "standard"—that is, batteries with a nominal voltage of 3.6–3.7 V, although in reality they also differ in many ways.
You're probably very familiar with this type of battery. You'll find them in laptops, tablets, phones, flashlights, power tools, power banks, and a huge number of other devices.

But they're also used in fairly large battery packs, from bicycles and scooters all the way up to cars—for example, Elon Musk's well-known Tesla.

Recently, so-called multi-component lithium batteries, such as LiCoO and Li-NMC, have become more common. I've even reviewed a couple of cells of this kind, both small ones and fairly high-capacity ones.
On the one hand, they're more appealing because they offer higher capacity in the same volume and cost less. Unfortunately, though, both "standard" and multi-component batteries share problems that are specifically related to operating in a UPS.
To start with, although multi-component batteries tolerate buffer operation better, in my personal opinion it's still safer to use them in cyclic mode. For that, however, your UPS or charger needs to be able to handle them properly.
But their voltage is a major problem.
The thing is, UPS units are usually designed around the voltage of a standard lead-acid battery, i.e. 12 V. In reality, that's the battery's average voltage; its full range is about 10–14.5 V, and in buffer mode it's 13.8 V.
Nickel-cadmium, nickel-metal hydride, and nickel-iron systems have a voltage of 0.9–1.45 V per cell. So with a 10-cell pack, we get a range of 9–14.5 V, which is practically equivalent to a standard lead-acid battery.
But when we build a pack from "standard" lithium batteries, we get an operating range of about 3–4.2 V per cell. That means three cells are too few (9–12.6 V), while four are too many (12–16.8 V). Even if you use a battery that’s slightly undercharged (which is actually beneficial), a pack of four cells will still reach 16.4 V, and some inverters simply aren’t designed to operate over that range.
One way to mitigate this is to use lithium batteries in a 24 V system. Instead of the typical 20–27.6 V range, a pack of seven lithium cells gives us a range of 21–29.6 (28.7) V. What’s more, modern inverters designed for use with solar panels let you adjust the pack’s operating voltage range quite flexibly.
Replacing a lead-acid battery with a lithium one is almost a perfect fit in a 36 V system: the lead-acid battery has a range of 30–41.4 V, while a pack of 10 lithium cells has a range of 30–42 V. That means it will charge to 4.15 V per cell, which is actually a good thing.
Unfortunately, although 36 V is part of the standard voltage range, inverters for 12, 24, and 48 V systems are much more common.

And now we’ve finally reached what I consider the most interesting type of lithium battery: lithium iron phosphate, or LiFePO4.

These batteries are also available in a wide range of sizes. For example, I reviewed some very small cells in size 10370, as well as much larger ones with a capacity of 90 Ah. And 90 Ah is by no means the limit—you can easily buy cells with a capacity of 280 Ah or even considerably more.

These batteries are also assembled into convenient packs that look like car batteries—or, more accurately, are designed to replace them. There are even enclosures for replacing UPS batteries; these most often use 32700 cells. I’ve reviewed several of them: the first, the second, and the third. By the way, they’re all currently in use with UPS units. In any case, I’ve already published quite a few LiFePO4 reviews.

The thing is, LiFePO4 batteries have an operating voltage range of about 2.5–3.65 V, so a pack of four cells gives us a range of 10–14.6 V, which is fully equivalent to a 12 V lead-acid battery.
LiFePO4 batteries also handle float operation much better. To use them this way, though, you need to maintain a charge termination voltage of about 3.45 V per cell, or 13.8 V for a pack of four batteries. That also exactly matches the float voltage for lead-acid batteries.
LiFePO4 batteries are also much safer than “regular” lithium batteries, which is especially important when using them in uninterruptible power supply systems.
Of course, there are some drawbacks. First, the price: these batteries are noticeably more expensive than lead-acid ones. But they also last much longer, so they’re more cost-effective in the long run. The second drawback is that you need to use a balancer (mandatory) and a protection board (recommended). The protection board is there to guard against voltage imbalance at the end of charging and discharging. But if your cells have very similar capacities and you use a balancer, you can narrow the inverter’s operating voltage range to keep each cell within its limits.

Another interesting type of lithium battery is lithium titanate, or LTO.
These batteries are also available in different form factors. Most often, they’re cylindrical cells with bolt terminals or prismatic cells in metal cases. But you can sometimes find them in the more familiar 18650 size. I even reviewed some of those, as well as even more unusual ones in cases resembling ordinary electrolytic capacitors.

The advantages of this battery type are its very long service life, high discharge current, wide operating temperature range, and safe operation. Its operating voltage range is also about 1.8–2.4 V, so a pack of six cells gives us a range of 10.8–14.4 V, which is also similar to the operating voltage of a lead-acid battery.
These batteries are often sold in lots of six. LiFePO4 batteries are also sold this way, but in multiples of four.
These batteries have two drawbacks: price and a poor capacity-to-volume ratio.

Before wrapping up, I’ll say a few words about lithium battery grades.
You’ll often see labels like Grade A or Grade B on product pages. I don’t have fully reliable information, but as far as I know, these are essentially equivalent to first- and second-grade products. In other words, after manufacturing, each battery is checked against its specifications and for its appearance. If its capacity or impedance (internal resistance) falls outside the limits set for the first grade, it’s assigned to less demanding applications. Batteries with possible mechanical damage go in the same category. But that doesn't mean Grade-B batteries are bad; more often, they simply have a wider spread in their specifications. For example, a battery may have slightly less capacity, which usually has no effect on its service life, while the price is lower.

A separate word about batteries from AliExpress. In my personal experience, even batteries that were initially more or less usable, albeit with a wide spread in their specifications, can simply swell up over time—even without being used, just after one charge-discharge cycle.
I'm talking about these batteries, for example. I wasn't keen on them even back then, but decided I might find a use for them after all. They'd been sitting around since I published the review, and when the war started, I decided to put together a battery just in case, so I could at least charge my phone, maybe something else too. I assembled it, charged it, everything was fine, and then left it alone for almost half a year. At the end of summer, I decided to run a discharge/charge cycle. By the end of the discharge, they had already swollen, and when I started charging them, I had to stop the process—I was simply afraid they might burst...
It's a shame, of course; they'd be very useful to me now. As it is, almost everything is running off a 4S4P battery made from 32700 cells. :(

So, there are plenty of batteries to choose from, but the best option depends entirely on the task and your budget.
Lead-acid batteries.
First, conventional or gel batteries. By and large, gel batteries are better, though I wouldn't say dramatically so. In my experience, they last longer. Gel batteries do cost more, of course, so it's up to you to decide whether they're worth it.
And a few general points about lead-acid batteries.
If your goal is simply to get through a difficult period, you don't want to spend a lot of money, and you don't want the hassle of assembling a battery, adding protection boards and balancers—and you don't mind the extra weight—then this kind of battery is for you. To be fair, balancers for lead-acid batteries do exist too; they're used when several batteries are connected in series.
Also, keep in mind that a lead-acid battery can't be charged quickly. So if the gaps between power outages are short—or if the power is off more often than it's on—you won't be able to charge it quickly during those breaks.
Nickel-based batteries.
The batteries themselves are good, but not many are made, and most are intended for industrial use. I'm not talking about small cells like AA batteries and the like, of course. Basically, if you happen to come across some that are inexpensive and in good condition, why not? But I'd think twice before buying new ones specifically for backup power...
“Conventional” and multi-chemistry lithium batteries.
In the context of UPSs, I'd rule out “conventional” lithium batteries right away—they come with too many problems. Multi-chemistry batteries are better, especially in terms of safety. But as I mentioned, the awkward voltage, the need to monitor the voltage of each cell, and some complications with float charging all create problems. In my view, the voltage is the biggest issue. Overall, they're probably for enthusiasts.
Lithium iron phosphate batteries
In my opinion, if you want your battery to last a reasonably long time, be safe, and charge quickly, this is probably the way to go. These batteries cost more than lead-acid ones, but they're easy to work with, offer more charge cycles, lose less energy output under heavy loads, can operate for a long time at high currents, and can be fully charged in a couple of hours. I think the price difference is worth it.
The downsides, apart from the price, are the need for a balancer and protection board, plus the work involved in assembling everything. That said, you can find people advertising their services who'll put it all together for you, for a fee, of course.
Lithium titanate batteries
The only major downside is probably the price. This is the option for when you want top quality and don't mind paying for it, with no compromises. Given their enormous service life, it's often a case of assembling the battery and forgetting about replacing it. But I probably wouldn't build one myself, mainly because of the price—especially considering that there's hardly any work available :(
That's all for batteries for now. In the next part, I'd like to explain how to assemble a battery, choose the cells, calculate the configuration, and so on. But you may have more interesting questions or topics for an article, in which case I might change my mind. Let me know—don't be shy; it matters to me ;)
As usual, a reminder: to keep up with new posts on the blog, I recommend following me on Instagram. I’ll post notifications about every new topic there, and might also write about something interesting from time to time — link to my account
So, let me start by saying that I don’t sell batteries, and until recently I hardly used them at home because I simply had no need to. But I’ve been involved with this subject before, and more than a hundred different batteries have passed through my hands during testing, so I’ve built up a bit of experience to draw on. The point is that batteries are often used incorrectly. At best, they simply work inefficiently; at worst, they can degrade relatively quickly. You can see an example of rapid degradation in this cycle-life test, where an incorrect charging profile killed the battery in just over a hundred cycles. Follow safe operating guidelines, though, and even a Chinese battery can last a long time, as shown in this cycle-life test.
I should also mention that I’ll cover the types of batteries you can actually find on the market. There’s no point writing about exotic types such as silver-zinc or nickel-hydrogen batteries, and so on.
First up, of course, are lead-acid batteries. You could sum them up in a few words: cheap and cheerful.
Yes, they’re readily available and inexpensive, but that’s about where the advantages end and the drawbacks begin, especially with the most common type, starter batteries:
1. Discharge current. You’ll see impressive figures like 250, 300, or 500 A, but forget about them. For starter batteries, those are only short-term current ratings. For sustained use without damage, they can deliver no more than 0.1–0.15C, where C is the battery capacity in Ah. So, for a typical 60 Ah battery, the continuous discharge current is only 6–10 A, or 70–120 W of power, not counting inverter losses.
2. Float charging. Ordinary lead-acid batteries don’t handle it very well. And if you use them in cyclic operation, they lose their charge relatively quickly during downtime due to self-discharge.
3. Charging current. Some might say, “What difference does it make? I can charge it whenever it suits me.” No—you can charge it when you have the opportunity, and not just any way you like, but at only 0.1–0.15C. That means a full charge (and what else would you need after a prolonged outage?) will take 7 to 12 hours. Will the battery have time to recharge between outages? Not necessarily.
4. Short service life. Yes, the low price comes at a cost: these batteries are unlikely to last for years. I’d plan on a year to a year and a half at most. But if you only need one for a relatively short time rather than for years of use, a lead-acid battery may be just the thing: use it, then recycle it.
By the way, I have a short review of a gel battery for a UPS, where you can see how the energy it delivers drops as the load current increases.
Here’s how you can address the problems listed above, or at least mitigate them.
You can compensate for the low discharge current by increasing the capacity. For example, a 120 Ah battery can deliver 12–20 A, or 150–250 W, which is much better. And there’s nothing stopping you from increasing the capacity even further—the discharge current will rise proportionally.
You can also use traction batteries. They’re designed for high discharge currents over extended periods, but they cost more and are less widely available.
Unfortunately, there’s no way around the low charging current: either accept faster aging or put up with a 7–12-hour charge.

Gel batteries are a type of lead-acid battery. The key difference is that their electrolyte is thick, so the battery can be installed in any position. Well, perhaps it’s best not to install it with the terminals facing down, although that is technically allowed too.
You’ve probably seen them in computer UPS units (and other types as well), but they’re also available in higher capacities. These batteries may last longer than conventional ones, though that depends heavily on the manufacturer.

But you need to be careful with batteries like these. First, it’s best to buy products from well-known brands, such as CSB or Yuasa.
Also, batteries like these can differ even within the same form factor. I’ll skip the obvious counterfeits with glass instead of proper internals, but I’ll explain the technical differences. Batteries with capacities of 7–9 Ah—the kind commonly used in computer UPS units—are also often used in other UPS units, such as those for alarm systems. The difference is in the current they can deliver. So you buy one of these inexpensive batteries, install it in your computer UPS, and a year later you suddenly find out that it’s dead. You can usually tell them apart by the price, so if you're installing them in a device that may draw a lot of current, use only branded batteries specifically designed for that kind of operation. The difference isn't just the price!

Next are the equally well-known nickel batteries, which have been in use for a long time and come in various types, such as nickel-cadmium and nickel-metal hydride.
You've probably seen batteries like these in cordless phones, toys, and power tools. But they are also made in much higher capacities and have long been used in uninterruptible power supply systems.
In my opinion, they have more advantages than lead-acid batteries, though of course they have their drawbacks too.
Their advantages include no need for balancing—this happens "automatically" during charging—and better tolerance of over-discharge. Lead-acid batteries are more "delicate" in this respect. They are electrically compatible with lead-acid batteries (10 nickel cells have the same voltage as a 12 V lead-acid battery), last longer than lead-acid batteries, and can deliver current continuously at 0.5–1C.
The drawbacks are a higher price, much lower availability, the "memory effect," and relatively high self-discharge.

Besides those mentioned above, nickel-iron batteries are also used. Many years ago, during the previous round of rolling blackouts, I once bought ten TNZh-450 batteries. They were dry, but in the end I never filled them with electrolyte and later sold them as they were. A battery like that has a capacity of 450 Ah, or about 4500 Wh, which is pretty good even by today's standards.
Batteries like these are still relevant and still being made, but are gradually being replaced by lithium batteries. You can still come across large battery banks, for example in telephone exchanges, electric vehicles, and so on.

Lithium batteries are the fastest-developing battery type, and they too have both advantages and drawbacks.
Broadly speaking, they can be divided into three types. I'll start with the first, which we can loosely call "standard"—that is, batteries with a nominal voltage of 3.6–3.7 V, although in reality they also differ in many ways.
You're probably very familiar with this type of battery. You'll find them in laptops, tablets, phones, flashlights, power tools, power banks, and a huge number of other devices.

But they're also used in fairly large battery packs, from bicycles and scooters all the way up to cars—for example, Elon Musk's well-known Tesla.

Recently, so-called multi-component lithium batteries, such as LiCoO and Li-NMC, have become more common. I've even reviewed a couple of cells of this kind, both small ones and fairly high-capacity ones.
On the one hand, they're more appealing because they offer higher capacity in the same volume and cost less. Unfortunately, though, both "standard" and multi-component batteries share problems that are specifically related to operating in a UPS.
To start with, although multi-component batteries tolerate buffer operation better, in my personal opinion it's still safer to use them in cyclic mode. For that, however, your UPS or charger needs to be able to handle them properly.
But their voltage is a major problem.
The thing is, UPS units are usually designed around the voltage of a standard lead-acid battery, i.e. 12 V. In reality, that's the battery's average voltage; its full range is about 10–14.5 V, and in buffer mode it's 13.8 V.
Nickel-cadmium, nickel-metal hydride, and nickel-iron systems have a voltage of 0.9–1.45 V per cell. So with a 10-cell pack, we get a range of 9–14.5 V, which is practically equivalent to a standard lead-acid battery.
But when we build a pack from "standard" lithium batteries, we get an operating range of about 3–4.2 V per cell. That means three cells are too few (9–12.6 V), while four are too many (12–16.8 V). Even if you use a battery that’s slightly undercharged (which is actually beneficial), a pack of four cells will still reach 16.4 V, and some inverters simply aren’t designed to operate over that range.
One way to mitigate this is to use lithium batteries in a 24 V system. Instead of the typical 20–27.6 V range, a pack of seven lithium cells gives us a range of 21–29.6 (28.7) V. What’s more, modern inverters designed for use with solar panels let you adjust the pack’s operating voltage range quite flexibly.
Replacing a lead-acid battery with a lithium one is almost a perfect fit in a 36 V system: the lead-acid battery has a range of 30–41.4 V, while a pack of 10 lithium cells has a range of 30–42 V. That means it will charge to 4.15 V per cell, which is actually a good thing.
Unfortunately, although 36 V is part of the standard voltage range, inverters for 12, 24, and 48 V systems are much more common.

And now we’ve finally reached what I consider the most interesting type of lithium battery: lithium iron phosphate, or LiFePO4.

These batteries are also available in a wide range of sizes. For example, I reviewed some very small cells in size 10370, as well as much larger ones with a capacity of 90 Ah. And 90 Ah is by no means the limit—you can easily buy cells with a capacity of 280 Ah or even considerably more.

These batteries are also assembled into convenient packs that look like car batteries—or, more accurately, are designed to replace them. There are even enclosures for replacing UPS batteries; these most often use 32700 cells. I’ve reviewed several of them: the first, the second, and the third. By the way, they’re all currently in use with UPS units. In any case, I’ve already published quite a few LiFePO4 reviews.

The thing is, LiFePO4 batteries have an operating voltage range of about 2.5–3.65 V, so a pack of four cells gives us a range of 10–14.6 V, which is fully equivalent to a 12 V lead-acid battery.
LiFePO4 batteries also handle float operation much better. To use them this way, though, you need to maintain a charge termination voltage of about 3.45 V per cell, or 13.8 V for a pack of four batteries. That also exactly matches the float voltage for lead-acid batteries.
LiFePO4 batteries are also much safer than “regular” lithium batteries, which is especially important when using them in uninterruptible power supply systems.
Of course, there are some drawbacks. First, the price: these batteries are noticeably more expensive than lead-acid ones. But they also last much longer, so they’re more cost-effective in the long run. The second drawback is that you need to use a balancer (mandatory) and a protection board (recommended). The protection board is there to guard against voltage imbalance at the end of charging and discharging. But if your cells have very similar capacities and you use a balancer, you can narrow the inverter’s operating voltage range to keep each cell within its limits.

Another interesting type of lithium battery is lithium titanate, or LTO.
These batteries are also available in different form factors. Most often, they’re cylindrical cells with bolt terminals or prismatic cells in metal cases. But you can sometimes find them in the more familiar 18650 size. I even reviewed some of those, as well as even more unusual ones in cases resembling ordinary electrolytic capacitors.

The advantages of this battery type are its very long service life, high discharge current, wide operating temperature range, and safe operation. Its operating voltage range is also about 1.8–2.4 V, so a pack of six cells gives us a range of 10.8–14.4 V, which is also similar to the operating voltage of a lead-acid battery.
These batteries are often sold in lots of six. LiFePO4 batteries are also sold this way, but in multiples of four.
These batteries have two drawbacks: price and a poor capacity-to-volume ratio.

Before wrapping up, I’ll say a few words about lithium battery grades.
You’ll often see labels like Grade A or Grade B on product pages. I don’t have fully reliable information, but as far as I know, these are essentially equivalent to first- and second-grade products. In other words, after manufacturing, each battery is checked against its specifications and for its appearance. If its capacity or impedance (internal resistance) falls outside the limits set for the first grade, it’s assigned to less demanding applications. Batteries with possible mechanical damage go in the same category. But that doesn't mean Grade-B batteries are bad; more often, they simply have a wider spread in their specifications. For example, a battery may have slightly less capacity, which usually has no effect on its service life, while the price is lower.

A separate word about batteries from AliExpress. In my personal experience, even batteries that were initially more or less usable, albeit with a wide spread in their specifications, can simply swell up over time—even without being used, just after one charge-discharge cycle.
I'm talking about these batteries, for example. I wasn't keen on them even back then, but decided I might find a use for them after all. They'd been sitting around since I published the review, and when the war started, I decided to put together a battery just in case, so I could at least charge my phone, maybe something else too. I assembled it, charged it, everything was fine, and then left it alone for almost half a year. At the end of summer, I decided to run a discharge/charge cycle. By the end of the discharge, they had already swollen, and when I started charging them, I had to stop the process—I was simply afraid they might burst...
It's a shame, of course; they'd be very useful to me now. As it is, almost everything is running off a 4S4P battery made from 32700 cells. :(

So, there are plenty of batteries to choose from, but the best option depends entirely on the task and your budget.
Lead-acid batteries.
First, conventional or gel batteries. By and large, gel batteries are better, though I wouldn't say dramatically so. In my experience, they last longer. Gel batteries do cost more, of course, so it's up to you to decide whether they're worth it.
And a few general points about lead-acid batteries.
If your goal is simply to get through a difficult period, you don't want to spend a lot of money, and you don't want the hassle of assembling a battery, adding protection boards and balancers—and you don't mind the extra weight—then this kind of battery is for you. To be fair, balancers for lead-acid batteries do exist too; they're used when several batteries are connected in series.
Also, keep in mind that a lead-acid battery can't be charged quickly. So if the gaps between power outages are short—or if the power is off more often than it's on—you won't be able to charge it quickly during those breaks.
Nickel-based batteries.
The batteries themselves are good, but not many are made, and most are intended for industrial use. I'm not talking about small cells like AA batteries and the like, of course. Basically, if you happen to come across some that are inexpensive and in good condition, why not? But I'd think twice before buying new ones specifically for backup power...
“Conventional” and multi-chemistry lithium batteries.
In the context of UPSs, I'd rule out “conventional” lithium batteries right away—they come with too many problems. Multi-chemistry batteries are better, especially in terms of safety. But as I mentioned, the awkward voltage, the need to monitor the voltage of each cell, and some complications with float charging all create problems. In my view, the voltage is the biggest issue. Overall, they're probably for enthusiasts.
Lithium iron phosphate batteries
In my opinion, if you want your battery to last a reasonably long time, be safe, and charge quickly, this is probably the way to go. These batteries cost more than lead-acid ones, but they're easy to work with, offer more charge cycles, lose less energy output under heavy loads, can operate for a long time at high currents, and can be fully charged in a couple of hours. I think the price difference is worth it.
The downsides, apart from the price, are the need for a balancer and protection board, plus the work involved in assembling everything. That said, you can find people advertising their services who'll put it all together for you, for a fee, of course.
Lithium titanate batteries
The only major downside is probably the price. This is the option for when you want top quality and don't mind paying for it, with no compromises. Given their enormous service life, it's often a case of assembling the battery and forgetting about replacing it. But I probably wouldn't build one myself, mainly because of the price—especially considering that there's hardly any work available :(
That's all for batteries for now. In the next part, I'd like to explain how to assemble a battery, choose the cells, calculate the configuration, and so on. But you may have more interesting questions or topics for an article, in which case I might change my mind. Let me know—don't be shy; it matters to me ;)
This page was found when searching for:
буферный режим lifepo4 bms накапливает ошибку, лучше инвертор по напряжению, батарея для ибп ,eathysq ht;bv 14 djkmn, как использовать lifepo4 в буферном режиме, как дать нагрузку на аккумулятор 24 вольта lifepo4, кислотном аккумуляторе в буферном режиме какое напряжение, литий ферумм акк в буферном режиме, буферное напряжение аккумулятора lifepo, буферный режим lifepo4 аккумулятор 12 вольт, li ion в буферном режиме, https://www.kirich.blog/stati/informaciya-dlya-nachinayuschih/1116-osobennosti-avtonomnogo-pitaniya-ili-chto-delat-v-sluchae-veernyh-otklyucheniy-chast-3-akkumulyatory, lifepo4 в буферном режиме, lifepo4 аккумулятор в буферном режиме, lifepo4 работа в буферном режиме, сделать 3 вольта с 3.7, 1, lifepo4 эксплуатация в буферном режиме, почему пухнут аккумулятор, SF8E40103/18V
буферный режим lifepo4 bms накапливает ошибку, лучше инвертор по напряжению, батарея для ибп ,eathysq ht;bv 14 djkmn, как использовать lifepo4 в буферном режиме, как дать нагрузку на аккумулятор 24 вольта lifepo4, кислотном аккумуляторе в буферном режиме какое напряжение, литий ферумм акк в буферном режиме, буферное напряжение аккумулятора lifepo, буферный режим lifepo4 аккумулятор 12 вольт, li ion в буферном режиме, https://www.kirich.blog/stati/informaciya-dlya-nachinayuschih/1116-osobennosti-avtonomnogo-pitaniya-ili-chto-delat-v-sluchae-veernyh-otklyucheniy-chast-3-akkumulyatory, lifepo4 в буферном режиме, lifepo4 аккумулятор в буферном режиме, lifepo4 работа в буферном режиме, сделать 3 вольта с 3.7, 1, lifepo4 эксплуатация в буферном режиме, почему пухнут аккумулятор, SF8E40103/18V
Questions and answers
What sustained discharge current can a 60 Ah lead-acid starter battery provide?
About 6–10 A, or 70–120 W before inverter losses. Figures such as 250–500 A refer to short-duration starting current.
How long does it take to recharge a lead-acid battery after a power cut?
At a charge current of 0.1–0.15C, a full charge takes about 7–12 hours. The battery may therefore not recharge fully between outages.
Which battery does the author recommend for long-term backup power?
Lithium iron phosphate (LiFePO4), citing safety, long service life, good performance under high loads and charging in a couple of hours. The battery requires a balancer and a protection board.
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments23
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.