/       /       /    A Pair of Step-Up Converters and a Small Upgrade to SEPIC
Support the project on Patreon


A Pair of Step-Up Converters and a Small Upgrade to SEPIC

$0.43
Go to store
I recently came across a review of 3.3 V linear voltage regulators.
I even joined the discussion, where the topic of powering devices designed for 3.3 V from a lithium battery came up.
Since this also tied in with one of my upcoming reviews, I decided to do a little experimenting myself.

This has actually been on my mind for a long time. According to the specs, I need to power a device that runs on 3.3 V and draws about 0.5–0.7 A, using a lithium battery.
At first I wanted to use an ultra-low-dropout linear regulator, but then I got a little board for a SEPIC converter and decided to explore that route.
My first thought was to order the ICs used in the ready-made converter, but then I got to thinking, which led to the subject of this review and to what I eventually built.

Okay, hold on—I’m getting way ahead of myself. Let’s back up.

I ordered two boards—or rather, two lots.
The first lot contained 5 boards, priced at $1.94 per lot, or $0.39 each.

You can actually buy boards like these offline too (and often more easily). At least you don’t have to wait a month for them. For example, the same converter is available from the Ukrainian store myproject.com.ua — link. The only thing is, with the shipping cost, it’s more convenient and cheaper to combine items into one order.


These boards are step-up DC-DC converters, initially set to 5 V.
They’re sold as strips, and if needed, you can easily snap off a board like a piece of chocolate.
This way of separating boards is called scoring: the PCB is cut almost all the way through at the required points, so you can snap it along the line when needed.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The board itself is pretty basic (well, apart from the fact that the IC contains a whole bunch of components).
When deciding what to order, I figured that even if nothing else, I could use the components individually. Even the sockets are worth something.
The soldering is neat, and the board is clean.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

But the connector looks like it was soldered with someone’s left hind leg—the complete opposite of the soldering on the other side, which was most likely done by a machine.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

I drew up a schematic from the board. Incidentally, I got one thing slightly wrong because I traced the circuit after doing the experiments—but more on that later.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

Since the board was clearly designed to be powered from a battery, I added a 330 µF, 6.3 V capacitor at the input to eliminate the effect of the wires.
I’ll say right away: all the boards started up without any problems.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

A quick test of the board. Since I bought these boards to modify them, this is really just to give you a general idea.
The board starts up at just over 1 V, and the output voltage is a little high.
In all the photos, the power supply is on the left (left display: voltage; right display: current), and the load is on the right, with the displays labeled.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The maximum output current I was able to get from the board with a 3.6 V input was 0.55 A.
When overloaded, the chip simply went into protection; the temperature never rose above 70 degrees during testing.
A quick note: for converters using a Step-Up topology, the toughest condition isn't a short circuit but an overload. With a short circuit, the current is limited by the inductor's resistance and the voltage drop across the diode, and the chip is disabled. But if the protection isn't implemented properly, an overload can kill the chip either through overheating or by exceeding the power switch's maximum current.
No matter how much I experimented, the board worked correctly and went into protection under overload, reducing the output voltage.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

I also checked what was happening at the converter's output.
The waveform clearly shows that the stock capacitor can't handle the ripple; adding 100 µF of capacitance at the output almost eliminates it.
The oscilloscope probe was set to 1:1 throughout all the tests.
In my opinion, the converter is pretty decent as-is.
The seller claims 200 mA from a 1.5 V supply and 500 mA from a 3 V supply.
In reality, if the figures are lower, they won't be by much.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The second lot consisted of a single board. The reviews were quite mixed and not always good, but since I was buying this board for experiments too, I didn't really care.
The board cost $0.6, link to the product.

These boards are also available in Ukrainian stores, for example here, although if you browse the store (it has a good selection), I'd probably pick something better. More convenient options have appeared since I wrote the review.



I was originally looking for a boost converter chip with reasonably decent specs. But my search eventually led me to boards with this chip, which cost only a little more and already came with the chip, an inductor, and various other small components.
There's no connector here, since the board is designed from the outset as a universal boost converter.
The seller's page lists these specs:
Input voltage: 2 V ~ 24 V
Maximum output voltage: 28 V
Maximum output current: 2 A
Efficiency: over 93%.
Dimensions: 36 mm * 17 mm * 14 mm.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

There are no components on the underside. The board's name matches the name of the chip installed on it—that's how I found it in the first place.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The board is small, especially considering that the contact pads take up quite a bit of space. Cutting off the pads would make it noticeably smaller.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The circuit is also very simple, based on the MT3608 IC, which even has a datasheet.
The IC's specs are quite good, in fact. I first found the datasheet, then the IC, and finally a board based on it.

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

I also traced the circuit from the board. Pin 4 is the IC's enable input; to turn it on, it must be connected to the power input.

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

But the first time I powered it up, I was very surprised.
At first glance, there's nothing unusual in the photo: the power supply is on, an electronic load is connected to the output, and its display shows a load current of 0.18 A.
Everything would be fine, except for one thing: the load's current control is turned all the way down, and its minimum current is 20 mA.
Something is clearly wrong.

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

It turned out that the board has high-frequency ripple at the output (the manufacturer specifies a frequency of 1.2 MHz).
Connecting a 100 µF capacitor in parallel with the output fixed the electronic load's erratic behavior.
The manufacturer—or rather, the designer—also contributed to the problem by placing the output capacitor near the IC instead of near the output terminals.
The board starts up at 1.8 V and holds the set output voltage well.

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

Reviews of the board said that the output voltage couldn't be adjusted.
Apparently, the person just couldn't figure it out, though the manufacturer is partly to blame here too.
The adjustment range is only over 8 turns of the trimmer out of 30! And you have to turn it counterclockwise O_o
In other words, starting from the usual maximum setting, you turn it 22 times with no effect, and only the last 8 turns adjust the voltage. Awful.

This IC also didn't overheat during operation, though it didn't deliver 2 A either.
Temperature measurements showed that above 1 A, the inductor and output diode on the board start heating up, so keep that in mind too.
But it's worth noting that you can get 2 A at the output only under certain conditions, and that's the maximum.

While writing the review, I realized that I had applied as much as 10 V to the input electrolytic capacitor (330 µF, 6.3 V, as in the first case), but since it was a good-quality capacitor, it took it in stride.

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

These are the board's ripple levels without an additional output capacitor. No wonder the load was “going crazy.”

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC


A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

Okay, time to get to the reason I needed all this (the board, that is).
I’d already reviewed a ready-made board and a fully DIY version. Now let’s try modifying a ready-made converter.

My line of thinking was roughly this:
I need a wide input voltage range, so I need a SEPIC.
Then I started looking for dedicated ICs, but thought: why do I need something specialized when a SEPIC converter is basically a modified step-up converter?
This point is actually very important: you can modify a step-up converter, but not a step-down converter, for two reasons—
1. The power switch in step-down converters is on the positive supply rail.
2. The power switch in these converters can be fully on, or switch off for only a very short time—which would almost certainly kill a step-up converter.

I found a suitable step-up converter IC and started looking for it on AliExpress, but ended up finding boards that used it.
After that, I set myself the goal of making a SEPIC converter by modifying existing step-up converter boards as little as possible.

Both types of converter are shown below. As you can see, the only difference is that the universal version has an extra inductor and capacitor. THAT’S IT!

A pair of step-up converters and a simple upgrade to SEPICA pair of step-up converters and a simple upgrade to SEPIC

I decided to start by experimenting with the small converters. I ordered a lot of five for a reason—it wasn’t just to save money.
The universal converter topology requires two identical inductors. Since I didn’t have any like that at home, I decided to take an inductor from another identical board (I had five boards in total).

A pair of step-up converters and a simple upgrade to SEPICA pair of step-up converters and a simple upgrade to SEPIC

While I was at it, I recalculated the feedback divider, first finding the IC’s comparator voltage.
In a simple program, I set up a 5.1 V source (that’s the boards’ output voltage), entered the values of the existing divider, and got about 1.22 V.
Then I changed the output voltage and adjusted one of the resistors so the IC would still see the same 1.22 V.
This has nothing to do with the SEPIC converter itself. I simply needed 3.3 V, but with the resistor values I had at home, I could only get 3.2 V.

A pair of step-up converters and a simple upgrade to SEPICA pair of step-up converters and a simple upgrade to SEPIC

And this is where the fact that I redrew the schematic after testing came back to bite me.
I wanted to use as few additional components as possible.
I took the inductor from one of the boards, used a resistor from my parts stash (though I could have taken that from another board too), and desoldered the capacitor from an old monitor board.
It would have been better to take the capacitor from one of the converter boards (the one I took the inductor from), since those capacitors have even higher capacitance and aren’t needed anyway.

A pair of step-up converters and a simple upgrade to SEPICA pair of step-up converters and a simple upgrade to SEPIC

Desolder the diode and solder the capacitor in its place.
Scrape the solder mask off a pad near the IC and solder one end of the inductor to it. Solder the other end to the pad where the diode’s cathode used to be.
Now solder the diode’s anode to that same pad, and its cathode to the right-hand lead of the 3.3 kΩ resistor (the LED is powered through it).
You also need to cut the trace; the spot is visible in the photo.

A pair of step-up converters and a simple upgrade to SEPICA pair of step-up converters and a simple upgrade to SEPIC

Let’s try it.
It starts at 1.28 V.

A pair of step-up converters and a simple upgrade to SEPICA pair of step-up converters and a simple upgrade to SEPIC

Although the board works, the output voltage stability leaves a lot to be desired.
At a low load current and an input voltage of 4.2 V, the output rises to 3.6 V. Not exactly critical, but not great either.
At currents above 500 mA, the protection kicks in and the output voltage drops.

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

After testing the board in different modes, I concluded that the maximum output current in my range would be around 300 mA, though it can briefly handle up to 400 mA.

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

During the experiments, I also tried increasing the capacitance of the capacitor between the inductors, but it made no noticeable difference :(

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

The ripple level, on the other hand, turned out to be quite good: step-up mode on the left, step-down mode on the right.

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

After playing around with the little boards, I moved on to a larger “test subject.”
The modification here is exactly the same, except that I only ordered one board. I ordered just one because I already had the required inductor on hand.
I also modified the output voltage adjustment circuit, removing it entirely and replacing it with a pair of resistors.

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

I also measured the comparator's reference voltage here and got 680 mV.
To do this, I set the output to 10 V, then desoldered the trimmer and measured its resistance as part of the voltage divider. In the diagram on the left, it is represented by the top two resistors.
Then I recalculated the divider for the voltage I needed (well, almost—I only had a 3.5 V resistor value close at hand), then gave up, checked the datasheet, and found out it was actually 600 mV, not 680 :)))
Anyway, I used a 2 kΩ lower resistor and a 9.1 kΩ upper resistor.
That's how experiments go :))))

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

Once all the calculations were done, I started modifying the board.
1. Desolder the trimmer and the 2.2 kΩ fixed resistor (or, to put it bluntly, desolder all the resistors).
2. Solder a 2 kΩ resistor in place of the fixed resistor, then cut the trace between the inductor and the diode.
3. Solder the second divider resistor to the back of the board (you can change its value later). I spent ages figuring out where to solder it, completely forgetting that I could solder it underneath :))
4. Solder a capacitor between the inductor and the diode. Same mistake here: I could have taken a capacitor from one of the other boards.
Solder a piece of lead from some electronic component to the inductor, pointing it toward the bevel on the inductor.
Clean and tin the pad near the output pads.

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

Solder one inductor lead to the pad near the output terminals, and the other (the wire lead) to the diode. I mentioned the bevel on the inductor for a reason—it helps it fit better.
That's it.

A pair of step-up converters and their minor upgrade to SEPICA pair of step-up converters and their minor upgrade to SEPIC

In the worst-case operating mode, with 2.6 V at the input, the board went into protection at around 700 mA. It was stable in all the other modes.
Overall, in terms of stability, this board is head and shoulders above the previous one.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

With an input voltage of 10 V, I easily got an output current of over 2 A, but the diode and inductors were already getting quite hot. The IC, meanwhile, stayed below 70 degrees.
The last photo shows that at low input voltage and an output current of 700 mA, the output voltage drops to 3 V.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

Above, I mentioned that with an input voltage of around 2.9 V (the minimum operating voltage of a lithium battery), I got 770 mA at 3 V.
I thought the cause might be the low capacitance of the capacitor installed between the inductors, so as an experiment I connected a second capacitor of the same value in parallel (the schematic shows the combined capacitance).

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

After the replacement, the output current clearly increased, and the voltage didn't drop to 3 V (or rather, 3.04 V) until the current reached 1.11 A.
So, with one capacitor, the maximum output power at an input voltage of 2.9 V was 2.31 W, while with two capacitors it was around 3.3 W.
I think that's progress.
These capacitors are quite expensive, so I'd actually recommend using the original 28 µF capacitor here, taken from the board's input. A 0.22 µF ceramic capacitor (or a couple of them) and a 100–220 µF electrolytic capacitor should be enough to replace it.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

A few more tests at different input voltages and output currents.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The tests showed that when powered by a single lithium battery (3–4.2 V range) with an output voltage of 3.3 V, the board can reliably deliver up to 700 mA.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

But the ripple on this board is clearly higher; that's probably its only drawback. This is the ripple with a 100 µF electrolytic capacitor on the output.
As I mentioned above, this is most likely due to poor PCB routing. An output ceramic capacitor might help, but I don't think it would make much difference.
SEPIC is generally considered the “noisiest” type of converter, so this is partly inherent to its design.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

The highest ripple was observed, of course, at maximum load current—or, more accurately, at maximum input current.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

Photos of both boards after the modification. On the larger board, the inductor fits neatly where the trimmer used to be; the smaller board looks a bit rougher.

A pair of Step-Up converters and a small upgrade to SEPICA pair of Step-Up converters and a small upgrade to SEPIC

And now a comparison photo of the new boards next to the board from this review.
You can see that the previous board looks huge compared with the new ones.

A pair of Step-Up converters and their minor upgrade to SEPICA pair of Step-Up converters and their minor upgrade to SEPIC

By the way, I wouldn't say the large board from that review is much weaker. In the previous review, I tested the converter with an input voltage of 14 V, an output voltage of 3.3 V, and a current of 2.5 A. This board managed to deliver only a little less.
But the price!!!..
If the previous converter cost $5.7, then even in the worst case here (buying two expensive boards), it would have cost $1.2.
And if you have a coupled inductor at home, you can get the cost down to around $0.8 (the board plus a pair of electrolytic capacitors).

The point of this review was never to measure the specs, efficiency, etc. precisely. Although I did quite a few different measurements, the goal was to make a universal converter by modifying cheap step-up converters.
I think the experiment was a success. With the second board, I got results comparable to those from the $5.7 board, which is more than good enough.
This review may also come in handy when you need something “here and now,” since step-up converter boards are much easier to find than universal ones (there are far fewer of them for sale, especially offline).

The first (small) board is of course a bit underpowered, and its output voltage isn't as stable as the larger board's. But you don't need to buy anything extra to modify it: you can make a universal converter out of two step-up converters.
You'll still have a spare IC, diode, LED, connector, and several resistors left over.
The second (large) board costs a little more, and you'll need either an inductor or a second identical board (the latter is preferable).

A few words about the boards in their original form.
The small ones — perfectly usable boards: inexpensive and not very powerful. Add even a small electrolytic capacitor at the output and ripple is low.
They probably won't quite manage the rated 200 mA (1.5 V) and 500 mA (3 V), but they'll come close.
They run cool and are reliable. I overloaded the board many times, but it stubbornly went into protection mode (the protection isn't latching).

The large one — well, that's a special case. A real example of how poor design can negate the good specs of the components used.
Yes, the board has decent components, and I really liked the IC (I'll have to buy a dozen or so as spares). But the layout is wrong, the trimmer is connected in a really odd way, and there are no electrolytic capacitors at the input or output (at these currents, they're definitely needed).
In other words, I didn't like the board as it is, but with a little work you can get good results from it. And you can get even better results by converting it into a universal converter :)

That's probably about it. The boards work, the job's done, the review is written. I'll be waiting for your questions in the comments :)
$0.43
Go to store
This page was found when searching for:
мт3608 переделать на отрицательное напряжение, преобразователь на mt3608 заменить дроссель 220 на 33 мкг, модуль 3608 доработка, какая минимальная разница между входным и выходным напряжением на повышающем dc dc преобразователе мт3608, доработка мт3608схема, hw668 схема включения на повышение напряжения, fm3608 или mt3608, чем отличается b6288p от b628, повышающий преобразователь hw-668 схема, 3115606, какая версия конвертера ascon step converter актуальна на сегодня, ascon step converter 1.6 разница, hw 668 преобразователь обзор, DC/DC convertor 1600W step-up, b62801 модуль ток потребления, mt3608 сколько витков дросселя достаточно, 6, dc dc step up 170v power convertor 668eub, step-up-перетворювач-схема, 5, підключити плату mt3608, как увеличить напряжение hw-668, схема паралельного соединения модулей mt3608, xl3608 datasheet, зачем применяется sepic

Questions and answers

What maximum current did the small Step-Up board deliver at a 3.6 V input?

The author measured 0.55 A. Under overload, the board reduced its output voltage and entered protection.

How can output ripple on the small Step-Up converter be reduced?

In the author's tests, adding a 100 µF capacitor at the output brought the ripple close to zero.

What problems did the author find with the larger boost-converter board?

He points to poor PCB routing, an incorrectly connected trimmer, and missing input and output electrolytic capacitors. He says the board can give good results after straightforward modifications.

The figures from this review are in the measurement database: Converters

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments25

Comments are published in their original language.

  1. Lisin
    29 January 2017 14:13#1
    Подскажите а чем отличаются микросхемы МТ 3608, В6285, В6286, SDB628.  Я понимаю что это одно и тоже/аналоги, но всёже! Разные производители? Партии? Где можно покапать?
    0
    1. 29 January 2017 22:19#2
      B628xxПервый работает от 2 Вольт и выше, остальные относятся к группе B628xx, т.е. фактически идентичны и имеют диапазон входного от 1.6 Вольта.
      Обычно все они отличаются сопротивлением встроенного полевого транзистора, частотой работы и диапазоном питания.
      Но чтобы сказать точнее, надо смотреть даташиты, а они есть не всегда. 
      +1
  2. 16 February 2017 23:40#3
    Подскажите, пожалуйста, какой ток потребляет вторая (большая) плата без нагрузки? Возможно ли ее использовать в паре с литиевым аккумулятором (защищенным) без выключения?
    0
    1. 17 February 2017 01:44#4
      Потребление на ХХ будет зависеть от входного и выходного напряжения.
      Кроме того зависит от того, сколько устройство должно работать от батареи.

      Попробую найти плату, но думаю минимум 5-10мА будет.
      +1
      1. 17 February 2017 11:15#5
        10mA... Получается, что литиевый аккумулятор 16340 на 700mAh эта платка посадит менее чем за 3 дня...
        Есть какие-то пути решения это проблемы? Например, как-то отключать 4-ножку микросхемы при отсутствии нагрузки? Только как?
        0
        1. 17 February 2017 11:41#6
          Ток попробую позже измерить, если найду плату :(
          А так да, обычно такие преобразователи не очень хорошо подходят для постоянного подключения.

          Отключать повышение можно, но как Вы правильно заметили, надо как-то определять наличие нагрузки. Повышающий преобразователь на выходе даже в выключенном состоянии будет выдавать входное минус падение на диоде, издержки схемотехники. 
          0
        2. 11 August 2020 13:07#7
          Ч ногу к питаемому устройству , как только подключите устройство ,  также и запустите преобразователь , мт3608 в режиме спячки ест 35мкА , возможно клоны потррбляют чуть больше, или мерьше.5
          +1
  3. 17 February 2017 11:25#8
    Можно еще вопрос? )))  Если нужен повышающий преобразователь на больший ток, например на 3-4 ампера, возможно ли собрать его на MT3608? Судя по даташиту у нее "Internal 4A Switch Current Limit".
    Если нужен значительно больший ток, например 5-10А, как будет выглядеть схема преобразователя? Возможно у Вас есть или планируется обзор на эту тему?
    PS. Еще раз спасибо за Ваши обзоры и за то, что Вы пишите с ликбезом для новичков!
    +1
    1. 17 February 2017 11:38#9
      Для начала надо понимать, что если надо получить большой ток на выходе повышающего трансформатора, то на входе ток будет еще больше.
      Причем чем больше выходное напряжение, тем больше будет ток на входе.

      Потому сначала надо знать, какое напряжение и ток нужны, иначе может получиться так, что аккумулятор "не потянет".

      0
      1. 17 February 2017 14:32#10
        Да, это понятно.
        На входе будет 1-2 литиевых аккумулятора, их напряжения известны. Ток они могут давать вполне приличный.
        Напряжение и ток на выходе пока для меня тоже не известны, но предполагаю, что это может быть от 9 до 18 вольт... Амперы тоже пока не известны.
        Данная схема может пригодится во многих случаях, поэтому было бы очень интересно, если у вас будет обзор на эту тему!
        +1
        1. 17 February 2017 20:11#11
          1 или 2 лития это большая разница, при 3 Вольта преобразователю очень тяжело работать, при 6 и более куда легче.

          Хотя даже не так, само повышение до 18 с током даже в 1 Ампер на выходе даст ток от одного аккумулятора около 7 Ампер. При токе в 2 Ампера будет уже 14-15, а это значит надо высокотоковый аккум.
          Если поставить два аккумулятора, то ток сразу упадет в 2 раза и будет не 7-15, а 3.5-7.

          Я подумаю насчет плат мощных преобразователей, но их редко делают под входное от одного аккумулятора, от 5-7 Вольт уже куда реальнее.
          +1
          1. 17 February 2017 21:52#12
            Цитата: kirich
            Хотя даже не так, само повышение до 18 с током даже в 1 Ампер на выходе даст ток от одного аккумулятора около 7 Ампер. При токе в 2 Ампера будет уже 14-15, а это значит надо высокотоковый аккум. Если поставить два аккумулятора, то ток сразу упадет в 2 раза и будет не 7-15, а 3.5-7.


            Да понимаю это я ))) Поэтому и писал, что 1-2 аккумулятора. 3 или тем более 4 - тяжелые слишком...
            Просто не расписал свою мысль полностью... Извините... не всем дано )))

            Цитата: kirich
            1 или 2 лития это большая разница


            Если 9 вольт то и 1 литий потянет же? И до 12 вольт, наверное? Хотя большого смысла нет, токи правда большие получаются.

            Если 15-18 вольт нужно будет, тогда конечно 2 лития уже нужно однозначно, или больше.

            Цитата: kirich
            Я подумаю насчет плат мощных преобразователей, но их редко делают под входное от одного аккумулятора, от 5-7 Вольт уже куда реальнее.


            Очень буду ждать! ))) 
            0
            1. 19 February 2017 00:03#13
              1 литий потянет и 12 и 18 Вольт и больше, вопрос только в токе, не более.
              У каждой микросхемы есть ограничение по току встроенного ключа, чем больше хотим получить, тем будет больше ток через ключ.
              С ростом входного напряжения ток через ключ будет пропорционально падать, соответственно может так быть что с 1 аккумулятором не вытянет, а с двумя проблем не будет.

              Потому надо сначала определиться с техзаданием.

              Да, возможно подберу пару повышающих преобразователей, тогда и обзоры будут :)
              +2
  4. 8 June 2018 18:43#14
    KIRICH, маленькие платки, вероятно, вполне подойдут для питания с/диодов  2835 и 5630 от 1,5 В ?
    0
    1. 11 June 2018 02:40#15
      от 1.5 думаю вряд ли, надо пробовать, не помню уже. Вообще они изначально ориентированы на литиевые аккумуляторы.
      0
  5. Юрий
    24 September 2019 16:06#16
    Добрый вечер. А смогу ли я с какой-нибудь из этих плат получить 15 вольт с током 0,36 ампера на выходе, при одной банке лития на входе?
    0
    1. 24 September 2019 23:02#17
      Можно попробовать со второй платой, которая без ЮСБ разъема, но вообще это 6 Ватт, на пределе будет.
      0
  6. 11 December 2019 11:10#18
    Добрый день! Подскажите, есть тех задание, требуется изготовить кастомный power bank с параметрами, параллельное соединение двух аккумуляторов 18650 для общей емкости 4800 mAh, зарядка платой внутри павер банки и step up на 7-8,4V с возможность выходного тока 3А.

    Контроллер заряда у меня уже есть на микросхеме ТР4056, нужен step up с требуемыми параметрами.

    Сам power bank будет питать фотоаппарат через "пустышку" в батарейном отсеке, для видеосъемки требуется 2А на выходе, а вот чтобы срабатывал затвор при фотосъемке нужны 3А. 
    0
    1. 11 December 2019 11:34#19
      Хм... А зачем повышайка если у Вас есть два аккумулятора и требуемое напряжение как раз как у двух аккумуляторов?
      Повышайка только добавляет проблем и одна из них - снижение КПД.
      0
  7. 11 December 2019 15:24#20
    Понимаю, что кпд будет ниже, но две банки последовательно дадут необходимое напряжение, но емкость только одной банки, а бъемся то мы как раз за автономность. Поэтому аккумы параллельно и повышайка.
    0
    1. 11 December 2019 16:55#21
      Я Вас расстрою, но два аккумулятора последовательно в любом случае дадут больше итоговую емкость, чем два параллельно с повышайкой.
      Берем две Ваши банки по 2400, включаем параллельно, получаем 4800мАч или 17.3 Втч, вычитаем КПД повышайки (около 85%), получаем 14.7 Втч
      Если просто соединить последовательно, то получим 2400мАч, но 17.3 Втч.

      Так что если Вы боретесь за автономность, то забудьте о преобразователях.
      0
  8. 11 December 2019 17:13#22
    Неожиданно, получается, если рассматривать две банки в параллель и последовательно, то в емкости выиграет последовательная сборка, если например рассматривать 3 и более банки в параллель, то тут уже без альтернативно выиграет параллель?
    Тогда два вопроса:
    1. Все же какую посоветуете повышайку с регулируемым напряжением и током 3А или выше для 3-4 банок в параллель.
    2. Если рассматривать две банки последовательно, то получается будет нужен BMS (можно ссылку?) и как эту BMS подключить к TP4056?

    +1
    1. 11 December 2019 17:58#23
      Без разницы сколько у вас банок, считайте емкость в Ваттчасах.

      +1
  9. 15 December 2019 04:49#24
    Граждане, подскажите пожалуйста - имеем умерший акб в блютус колонке и 4 новых акб.
    Правильно ли я понимаю, что при сборке батареи, скажем 1s4p - параллельного соединения для увеличения емкости на 3.7v , из плоских аккумуляторов Li-Po, у которых на каждом аккумуляторе уже есть плата защиты от разряда/переразряда/кз/перегруз, балансир не нужен, тк его некуда подключать, да и если какая-то банка деградировала и потеряла емкость, то либо её отключит её защита от переразяда, или отключит защита по силе заряда тока как и соседние банки по силе разряда тока, которые станут её подзаряжать.АКБ 605060 у продавца содержала запись "Встроенный интеллектуальный модуль PCB защиты, эффективно предотвращает перезарядку, разрядку, перегрузку по току и короткое замыкание."Нужно ли еще подключать какие-то платы при смене умершей АКБ на четыре новых акб в параллели.
    Спасибо!

    4 акб https://ru.aliexpress.com/item/4000174132622.html A Pair of Step-Up Converters and a Small Upgrade to SEPIC
    +1
  10. 29 June 2020 15:44#25
    Казус с оборотами подстроечного резистора вероятнее всего связан с неверным подключением его, правильнее соединить ползунок с нижним резистором делителя, что вероятнее всего делают в новых версиях плат, потому-что таких эффектов в недавно преобретаемых платах ненаблюдается.
    0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister