/       /       /    ZXY6020S, or the next chapter in the story of a DIY high-power bench power supply
Support the project on Patreon


ZXY6020S, or the next chapter in the story of a DIY high-power bench power supply

$71.56
Go to store
About a year and a half ago, I already published a review using the smallest board in the ZXY60xxS family of DC-DC converters.
The power supply is in good working order and works perfectly. But using it has shown me that I want something different. So about a year ago, I started planning a more optimal power supply (at least for me).
Anyway, if you're curious about what I ended up cobbling together, read on.
Warning: lots of photos, so this page uses a lot of data.

First, I should mention that I'll often refer to a series of reviews from a year and a half ago, where I covered a less powerful version of this board, how to use it, and the additional modules and components used at the time.
I also asked the store to add this board to its product range. In other words, I came up with the idea for this review long before ordering the board, let alone receiving it.

Using the previous version of the board showed that it was quite convenient to work with and had reasonably good specs and a wide output voltage adjustment range, but its output current was very low.
Yes, the power supply's maximum output power was 300 W, which is perfectly reasonable; inexpensive power supplies usually have a power rating of 150–200 W.
But the maximum current was limited to 5 A, or more precisely, 5.2 A.
I often have to repair all kinds of power supplies, as well as automotive step-up inverters. To troubleshoot them, I need to be able to adjust their supply voltage.
And with an output current of just 5.2 A, at 14 V I can get only 73 W. That's not much—very little, in fact.

When I ordered the previous board, I didn't know how it worked, but I discovered during testing that it had a very useful feature.
It lets you set the maximum output power.
For example, I need high current at low voltage, but that doesn't mean I need the same current at the maximum voltage. I figured that 5–10 A would be enough for me at 60 V.

That was the idea that came to me a year ago.
This power supply can deliver over 300 W at 14 V while its maximum output power is set to 700 W—far more than the 73 W available with the previous version. It can also deliver over 600 W at 28 V (for 24 V inverters).

Okay, I've gotten way ahead of myself. It's probably time to get on with the review and fill in the rest as we go.

Everything inside is carefully wrapped in bubble wrap. On top is a USB-RS232 TTL converter, which I wasn't even expecting.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

And here's the converter. I wouldn't say it's large for the rated power—in fact, it's quite the opposite.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Unlike the previous ZXY6005, this one consists of two boards. The mid-range ZXY6010 has exactly the same design.
One board contains the power stage; the other handles control, display, and current measurement.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The converter's stated specifications.
In reality, the maximum output voltage is 62 V and the current is 22 A, giving over 1300 W.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The design is very well thought out: the boards are connected by two lines, one for power and one for control. You can easily disconnect the boards from each other, which is genuinely convenient.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

First, let me show you what the control board looks like.
For the most part, it looks very much like the ZXY6005 board. In fact, I’d say it’s more than just similar.
The processor section, analog circuitry, controls, and display are identical, apart from a few minor details. And, of course, some resistor values in the current measurement circuit are different.
The main difference is that almost all of the power circuitry, along with the 12 V preregulator, has been moved to a separate board.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The Jamicon capacitors were a pleasant surprise. I wouldn’t say they have any outstanding specs, but they’re quite reliable and much better than no-name alternatives.
The control section, buttons, and encoder are identical to those on the lower-power board.
The terminal blocks are a bit beefier, though, which makes sense: a current of up to 22 A puts its own demands on the components.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The back of the board is completely bare—no components at all, just PCB traces.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Since the boards are designed to be stacked, they have the same dimensions: 130 × 85 mm.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The control buttons are at the bottom of the board. Their functions are the same on all the boards.
1, 2 — increase/decrease, and select the display mode.
3 — select a memory slot or move the cursor when adjusting parameters.
4 — select the parameter to adjust.
5 — turn the board’s output on/off, and confirm parameter selections.

As with the previous version, there are two annoyances:
1. The ± buttons are arranged the opposite way from what I’m used to: increase on the left, decrease on the right.
2. The buttons connect to the ADC input, but the voltage range triggered by pressing them is very small, so don’t forget there’s a keyboard calibration mode.
To calibrate: turn off the power, press the OK button, turn the power back on, and release the button when the calibration value appears.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

To the right of the keypad is an encoder that essentially duplicates the ± buttons, except for selecting the operating mode.
On the left is a connector for connecting to a computer—a pretty useful feature.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Some of the components are hidden beneath the display, which can be removed after unscrewing four screws.
Since the converter is fairly complex and the board is single-sided, the layout is quite dense.
The large number of connectors is immediately noticeable.
At the top left is the connector linking the board to the power module; below it is a connector that duplicates the power switch.
At the bottom left are connectors for connecting to a computer and an external keyboard.
At the bottom right are two small connectors: a three-pin one for connecting an external encoder, and a two-pin one for the voltage feedback connection.
At the top right is the connector for the operating-mode indicator LEDs.

ZXY6020S, or the next chapter in the story of a powerful DIY lab power supplyZXY6020S, or the next chapter in the story of a powerful DIY lab power supply

1. This board uses an STM8S105K6T6C microcontroller; the lower-end version had an STM8S105K4T6C.
2. The microcontroller is powered by an AMS1117 linear regulator with a 3.3 V output.
3. Although the analog section is laid out just like on the previous board, it uses different op-amps. Last time they were Microchip op-amps; this time, precision TLC272 op-amps from Texas Instruments are installed.
4. The XL1509 PWM controller has been replaced with a more powerful LM2596S.
This controller drives a power transistor mounted on the power board.
The operating frequency is 150 kHz.
5. The board has three LEDs indicating the operating mode.
Output voltage is on.
The power supply is operating in voltage-limit mode.
The power supply is operating in current-limit mode.
6. All of this is powered by a 5 V linear regulator (the op-amps run on 5 V).

It’s worth noting that the device is fully functional right out of the box, i.e. the board has all the necessary controls and indicators.

ZXY6020S, or the next chapter in the story of a powerful DIY lab power supplyZXY6020S, or the next chapter in the story of a powerful DIY lab power supply

Besides the “low-level” electronics, the control board also has the power supply output filter capacitors and a current-sense shunt.
The capacitors are rated at 2200 µF and up to 63 V.
The voltage rating is cutting it close: using 63 V capacitors with a 62 V output is a little risky.
The photo also shows large terminal blocks for connecting the power wires. They’re good quality; no complaints.

ZXY6020S, or the next chapter in the story of a powerful DIY lab power supplyZXY6020S, or the next chapter in the story of a powerful DIY lab power supply

Judging by the marking and my estimates, the shunt resistance is just 2.5 mΩ.
I wasn’t sure about the marking—or rather, the order of the digits—so I did a quick calculation based on the heating.
At 2.5 mΩ, the shunt dissipates about 0.0025 × 22 × 22 = 1.21 W.
At 25 mΩ it would be about 12.1 W, and since the shunt is only slightly warm, the first value, 2.5 mΩ, is the right one.

The connector for the power board has just six pins, two of which are ground (I’ll explain why later).
The other pins are for:
12 V to power the control board
PWM signal to drive the power transistor
Fan control
Signal from the temperature sensor.

ZXY6020S, or the next chapter in the story of a powerful DIY lab power supplyZXY6020S, or the next chapter in the story of a powerful DIY lab power supply

Power module.
The layout here is clearly less cramped. Most likely, they chose the control board’s PCB dimensions as the starting point, then made the power module to fit the same size.

ZXY6020S, or the next chapter in the story of a powerful DIY lab power supplyZXY6020S, or the next chapter in the story of a powerful DIY lab power supply

The board is screwed to a fairly substantial heatsink, with the transistors and diode assemblies mounted on it.

ZXY6020S, or the next chapter in the story of a powerful DIY lab power supplyZXY6020S, or the next chapter in the story of a powerful DIY lab power supply

It’s worth mentioning one of the board’s useful improvements separately.
The thing is, in previous versions of the board, the power supply was implemented by converting the input voltage to a secondary 12 or 5 V (on the 6005 board) using a PWM controller.
There were a lot of complaints about this circuit design, since reliability was very poor. I’ve already come across reports of these converters failing several times.
The board should really be supplied with at least 65–70 V at the input, which is already a pretty demanding operating condition for inexpensive PWM controllers. I replaced the controller in my 6005 with a more expensive one and made a few modifications to reduce the voltage, but that’s expensive and complicated.
Here, the manufacturer first installed a linear regulator that drops the voltage to 54 V. To reduce the inrush current, its output is connected through a resistor to the filter capacitor, followed by a 12 V converter.
In other words, the circuit is: input voltage — 54 V linear regulator — 12 V PWM regulator (fan and power electronics) — 5 V linear regulator (op-amps) — 3.3 V linear regulator (processor).

Many thanks for this improvement. By the way, the datasheet still includes an older photo without the linear regulator.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

The power board also has a connector with the same pinout as the one on the control board, with a power terminal block next to it.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

1. The XL7005 is used as the PWM controller to step 54 V down to 12 V. Its maximum input voltage is 65 V, so 54 V is well within its limits.
Keep in mind, though, that its maximum output current is 0.5 A, so don’t connect high-power loads to this supply. It also has rather unreliable short-circuit protection, which I tested on the previous board with poor results :(
2. The fan is switched by an MJD122 bipolar transistor.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

The board also has a driver for a high-power MOSFET. Essentially, it’s a driver stage for controlling a power switch connected in the positive supply line.
I couldn’t figure out the circuit, but I can say that it uses a somewhat unusual approach. I usually use more conventional high-side drivers in circuits like this.
The purpose of the LED is also a mystery to me.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

The driver uses two well-known NE555 timers. One is on the primary side of the pulse transformer and controls the transistor connected to the transformer.
The second timer is installed in the “high-side” part of the driver.
Odd and hard to understand, but it works :)

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

The inductor looks very small, especially considering that the board has a maximum output power of 1200 W.
Although, given that the manufacturer recommends active cooling, perhaps it’s fine. Still, I’d make it larger (keeping the inductance unchanged) and use thicker wire. That would definitely improve its thermal performance.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

The capacitors here are generously rated; last time, the input capacitors were also rated for 63 V.
Here, two 1000 µF, 100 V capacitors are installed.
A terminal block for supplying power to the board is located next to them.
To the left of the capacitors is a diode connected in parallel with the input to protect the board against reverse polarity. It offers little protection at high currents, but in a pinch it will burn out and short the power supply, protecting the electronics in the process.
There is a second diode next to the power inductor, connected in parallel with the power transistor.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

Removing the board is easy: all you need is a Phillips screwdriver. Convenient :)
All the components are mounted with thermal pads, so the heatsink has no electrical contact with them and can be attached to a metal enclosure.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

Mounted on the heatsink are:
1. A temperature sensor
2. Two STPS20H100C diode assemblies, each rated for up to 20 A (for the entire assembly) and 100 V. With two assemblies, the maximum current is 40 A, with no safety margin; ideally, the diode current rating should be twice the output current.
3. Surprisingly, the power switch is an IXYS transistor. This company makes very good power components, so it’s nice to see one of their parts here.
The installed transistor is marked IXFH160N15T2. It’s a powerful N-channel MOSFET rated for a maximum current of 160 A and a voltage of 150 V, with an on-resistance of 9 mΩ.
4. Unfortunately, I couldn’t identify the transistor in the 54 V linear regulator. The marking was either missing from the start or completely worn off :(

Since I couldn’t bend all the components out of the way, I had to desolder the transistors. I also noticed that the MOSFET is soldered into the board as far as it will go, and even bends the board slightly.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

Naturally, I made a few modifications too.
I made quite a lot of changes to the board, and I’ll describe them all.
But I should also say that the board works perfectly well without any of these modifications.
The goal was to improve reliability and performance, with reliability the top priority. And once I’d started working on it, I just couldn’t resist making a few improvements.

First, I used 0.75 mm² wire to reinforce the power traces on the board, and added a generous amount of solder to them as well.
The average current through these traces can reach 22 A, and the pulsed current can hit 44 A, so increasing their cross-section gives us a small improvement—and it’s easy to do.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

The diode assemblies are connected through small balancing resistors. I can’t measure their resistance, but the fact that these “jumpers” are used even where a simple trace would have done suggests they are low-resistance resistors in jumper form.
This is the right approach, but some of these jumpers didn’t seem to be soldered very well, so I went over them again with the soldering iron.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

The next modification was replacing the capacitors with better-quality ones. I used good Capxon KF-series capacitors.
Four 220 µF, 25 V capacitors were replaced with ones of the same specifications.
After that, I prepared some additional components that weren’t originally on the board but should improve it.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

A few useful modifications to the power board.
First, improving the board's protection.
1. Cut the trace near the input terminal block. It runs from a small protection diode that blocks power if the input polarity is reversed.
2. Solder a fuse into the break in the trace.
3. I used a 315 mA fuse. The board's current draw varies with the input voltage and is around 200–80 mA. The higher the voltage, the lower the current.
4. While I was at it, I bought a 1.5KE13A TVS diode for protection. It's essentially a high-power 13 V Zener diode.
5. The TVS diode is soldered in parallel with the output capacitor on the 12 V rail, after the PWM regulator.
Its purpose is to prevent the voltage from rising if the 12 V power supply's PWM controller fails, and to blow the fuse in the process. This protects the board's “brains” in the event of a fault.
6. I also installed a 220 µF, 100 V capacitor in parallel with the board's power output.
The wire from the inductor to the filter capacitors is quite long, so there could be interference from large current spikes.
The previous board revision had a capacitor here, but it was later moved to the control board. I decided to do things my way and added another capacitor to the power board. Its capacitance is small, but it certainly won't hurt.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

This next modification is more of a “why not, since I can?” kind of thing.
I replaced the rubber thermal pads with mica pads.
A while ago, I did a review comparing the thermal conductivity of different pads, and mica performed better than rubber, so I decided to make the switch.
I left the pad under the 54 V linear regulator transistor as it doesn't dissipate much heat.
I also applied some KPT-19 thermal paste. As far as I can tell, its specs are slightly better than those of the popular KPT-8.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

This is what it looks like after the modifications, before bolting the board and heatsink together as one unit.
At the time, I didn't think I'd have to take it apart again.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

1. One of the power inductor's leads acts as a jumper between the board layers.
In other words, the trace runs along the top of the board, then switches to the other side at the lead. I decided to solder this joint to reduce the current load on the plating in the board's vias.
2. The replaced and added components.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

Overall view of the board after the first round of modifications (I didn't think there would be more than one round).

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

The control board also got a few modifications, though not as many.
1. I bought a TVS diode for this board too, this time a 1.5KE6.8A rated for 6.8 V.
2. This TVS diode is connected in parallel with the 5 V rail to protect at least the processor, if not the op-amps.
This TVS diode is there in case the first stage of protection fails.
The op-amps, PWM controller, transistors, and diodes can all be replaced, but if the processor dies, the board is definitely headed for the trash. Since the board isn't cheap, I'd rather not have to do that. Last time, the regulator failed, but the processor survived. I definitely gained a few gray hairs, though.

ZXY6020S, or the continuing story of a DIY high-power bench power supplyZXY6020S, or the continuing story of a DIY high-power bench power supply

Test power-up after the modifications.
I did test the board a little before modifying it, but since it took a long time to prepare this review, the photo chronology got out of order. So I’ll be posting the photos in a somewhat incorrect sequence—sorry about that.

For the first power-up, I used the previous power supply, just for convenience.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

When powered on, the screen briefly displays the board model and manufacturer, as well as the firmware version.

After that, the voltage and current selection menu appears.
By default, the board is set to 12 V and 5 A, but you can change this to any other values if you like.
More precisely, the board starts up with the settings stored in memory slot M0. After that, you can either select the parameters you need or choose a memory slot (there are 10 in total) with settings already saved (the other slots are empty by default).
The maximum settings are 62 V and 22 A, so it would be more accurate to call the board a 6222, but the manufacturer rounded the specs down and named the model 6020.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Once I’d confirmed that the board worked, I moved on to the remaining modifications.
I also reinforced the high-current traces on the control board, but there’s an important caveat here.
Because the shunt has such low resistance, increasing the trace width near it (or, more precisely, in one spot) also affects current measurement accuracy.
One of the shunt terminals (the one closer to the board’s output) is connected correctly: the high-current trace is on the underside of the board and the sense trace is on top, so soldering it doesn’t significantly affect measurement accuracy.
The other terminal is more sensitive to modifications. If you don’t want to recalibrate, it’s best not to add solder within 5 mm of the shunt.
Strictly speaking, soldering doesn’t affect measurement accuracy directly; it changes the resistance. You can solder it however you like, but then you’ll need to calibrate the current setting and ammeter readings. I decided not to recalibrate, so I simply left that spot alone.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The next modification involved rearranging the components rather than replacing them.
To do that, I had to desolder the large capacitors. I measured their capacitance while they were out, and there was no shortfall—they were fine. It’s hard to see in the photo, but they measure 2290 µF against the rated 2200 µF.
Ideally, they should be replaced with 80 V or 100 V capacitors, but I’ll do that another time, once I find something suitable.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The modification consisted of repositioning the capacitors horizontally. This was necessary because of the enclosure I planned to install everything in.
I secured the capacitors with a cable tie through holes drilled in the board. There aren’t many traces in that area, so drilling the holes was no problem.
I also rubbed the markings off the shunt, so I had to write them back on with a marker :)

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

To secure the board inside the enclosure, I used four small angle brackets. Their threads were for 2.5 mm fasteners, and I only had a couple of brackets at home that fit standard 3 mm screws.
Since it’s best to use the same type of fastener throughout a single assembly, I decided to use 2.5 mm brackets for all four.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The mounting is designed so that the heatsink sits slightly above the surface. This improves airflow a little and makes it easier to screw in place. The brackets are installed with their flanges facing inward, so they don't take up extra space at the sides of the heatsink. It also makes things a little safer (no screws sticking out) and looks better.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

I decided to save a little on the standoffs that will hold one board above the other.
I could have used standard M3 threaded standoffs, but I had some tubes lying around with an inner diameter of 3 mm. They came from Polish log-periodic antennas and can be found at markets.
One end of each tube already has an M3 threaded stud installed, which makes things easier.
At the other end, I screwed in standoffs from computer cases. Their outer thread is slightly larger than 3 mm, and the inner thread is M3.
I think the process is clear from the photo: clamp the tube in a drill driver, hold the standoff with pliers, and screw it in at low speed. Very convenient.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

And here are the resulting neat (well, almost neat) little standoffs :)

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Screw the standoffs in place of the power board's mounting screws.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Next, stack the boards like a sandwich.
The standoffs are sized to leave a small gap (5–6 mm) between the tops of the capacitors and the underside of the upper board.
There was another way to assemble it: install the control board upside down, with the components facing down. That way, the capacitors wouldn't need to be resoldered. But my goal was to make a device that's easy to service and, if necessary, repair.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

Here's the assembly from the side. You can see the gap between the large capacitors on the power board and the control board.
When I was working on the power board modifications, I forgot to measure the inductance of the power inductor, so while I still had the chance, I decided to correct that oversight.
To take the measurement, I desoldered the capacitor connected to the output so it wouldn't affect the reading.
The meter read 139.6 µH. I think this information may be useful when modifying the board and replacing the power inductor.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The assembly is complete; time to move on to the electrical connections.

I wasn't happy with the original power wires: their cross-section was around 1–1.5 mm², and the quality wasn't great either, so I decided to replace them.
For this (and other projects), I bought extra-flexible wires in several gauges, one meter of each color pair (red and black): 2.5, 4, and 6 mm². I don't remember how much they cost, but altogether they weren't exactly cheap.
Although I bought flexible wire, I used rigid 6 mm² wire for the power connection between the modules. It was easy to bend into the required shape and turned out to be better suited for the job.
I used 2.5 mm² wire to connect the power supplies; the current in this circuit won't exceed 11 A, even at maximum output.
Finally, I secured the control wires, just so they wouldn't dangle all over the place :)

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

I think it's worth taking a short detour to talk about choosing the enclosure, since it influenced changes to the power module design and the choice of components.
Since the unit was intended to be powerful and fairly heavy, I immediately ruled out plastic enclosures.
I wanted a metal enclosure, preferably sturdy and good-looking.
The selection of enclosures like that is very limited, and finding one for a specific project turned out to be almost impossible. So my first thought was to buy an old oscilloscope or some other broken piece of equipment, gut it, and give it a makeover so it would look nice.
Searching flea markets and forums showed that there were some options, but they were either downright ugly, the wrong size, or prohibitively expensive.

In the end, I checked AliExpress and quickly found a suitable enclosure, but the price wasn't appealing. Understandably, buying something like this from China is very expensive because of the shipping cost.
Imagine my surprise when I decided to look for the same enclosure in local online stores and found one in Odesa for a noticeably lower price than in China :))))
It cost me about $30 at the time, including shipping within Ukraine, and I got it a couple of days later.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

The enclosure is really gorgeous.
Dimensions: 220 x 275 x 120 mm — link to this enclosure and to all the options.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

One particularly nice and convenient feature is that the enclosure is split asymmetrically: the top cover is taller than the bottom, which makes assembly easier. The enclosure is sturdy, and the front and rear panels fit tightly with no play.
It came with a handful of black screws. The top cover is secured with 8 screws, the bottom with 6, and 4 spares were included.
It's convenient that the front and rear panels are easy to remove. They slide out forward or backward, rather than lifting off, as with plastic enclosures.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

I also made a quick trip to the electronics market, where I picked up various connectors, wires, a fan and its grille, plus a bunch of other odds and ends. The photo shows some of what I bought; the rest was picked up as the project went along.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

One of the things I bought was a batch of capacitors I needed to modify the power supplies.
I've already reviewed these power supplies; they're 36 V, 10 A, 360 W units.
The power supplies are pretty decent as they are, but since I was already building the unit, I decided to modify them too, just to be on the safe side.

I bought six 1000 µF 63 V capacitors and four 220 µF 25 V capacitors for them.
I also found a couple of 100 µF 400 V capacitors at home.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

I simply replaced the original capacitors with the first two types (220 µF and 1000 µF). To install the 100 µF 400 V capacitor, though, I had to remove the input voltage range selector connector.
The installed capacitor is shown at the top of the photo.
I had to bend its negative lead, but it all worked out fine. In my review of this power supply, I mentioned that it would be a good idea to increase the input electrolytic capacitance, since the manufacturer had fitted capacitors with too low a value.
This capacitor is connected in parallel with the output of the bridge rectifier.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

To install the capacitor, I drilled a pair of holes in the board, scraped the traces clean, and soldered the leads there.
The photo shows where to solder. I don't think anything is fundamentally different in other power supplies.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

But that wasn't all the modifications.

Warning: When connecting any power supplies with metal enclosures in series, make sure the negative output terminal isn't connected to the power supply's case, or you'll get an unpleasant surprise!

Since the power supplies are connected in series, it's recommended to install diodes in parallel with the power supply output to protect them.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

I picked some diodes from my old stock: 2D213. I didn't need the mounting washers, though.
I spent a long time figuring out where to put them. In principle, I could have installed them where the missing diode in the output rectifier goes (there's room for two diodes, but only one is installed).
But I wanted a design that could be taken apart.
So I installed the diodes underneath the circuit board. The idea was for the board itself to press the diode against the aluminum case.
Since there's a plastic insulator under the power supply, I cut a hole in it.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

I put everything together, added a mica insulator, screwed the board in place, and found that the diode wasn't pressed firmly enough—in fact, it was barely touching.
I had to dig out some thick, thermally conductive rubber (1.5 mm) from my stock. I'd reviewed it once before, so I used that.
Since this diode only operates briefly (in an emergency) and dissipates no more than 10 W even in the worst case, this solution is acceptable.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

I put everything back together, but at the last moment I remembered that the diode assembly in one of this company's power supplies (48 V, 5 A) had been clamped crookedly.
There wasn't much of a problem here, but I decided to play it safe and added a small piece of metal to improve the contact.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

First test fit of the power supplies and converter board in the new enclosure.
I think it's now clear why I modified the control board and laid the capacitors on their sides.
Actually, I didn't have to do that. The whole assembly fit just fine either with the control board upside down—which was inconvenient—or with it in its current position and the capacitors mounted vertically, but that wasn't safe because everything was packed in with absolutely no clearance.

For the reasons mentioned above, I decided to lay the capacitors on their sides and also raise the module slightly above the bottom of the enclosure. That seemed like a better solution.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

During the test fit, I found that the power supplies couldn't be installed close to the rear panel because the enclosure's feet protrude inward and get in the way.
I had enough room, but didn't want to waste it, so I trimmed the power supply cases a little with side cutters.
If you make the same modification, don't throw away the pieces you cut off; they may come in handy later.

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

From here on, things followed the usual plan. I positioned the power supplies and converter module in the enclosure so they’d be easy to access and wouldn’t get in the way, marked the holes, drilled them, and removed the burrs. One hole was slightly off, so I had to drill it out a bit more later, but otherwise everything went great.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

I installed the power supplies and module in the enclosure, hoping I wouldn’t have to take them out again.
Two screws are enough to secure each power supply; they’re rock solid.

The design was thought out so that the power supply fans would draw air in through the enclosure’s ventilation holes, while the power supply cases would form a sort of “corridor” for the airflow generated by the exhaust fan on the rear panel.
The power supplies stop about 5 mm short of the top of the enclosure. The design could be improved by adding something flexible along the top edge of the power supply cases, which would direct the airflow better, but I didn’t bother.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

While experimenting with the module, I found that it can display the heatsink temperature. At least, it has a T-SNS function, and the settings menu includes an option to shut it down at a user-defined temperature.
But the screen only showed the number 48, without saying what the 48 referred to (just like in that famous joke).

Without giving it much thought, I screwed the whole assembly together and installed it in the enclosure, figuring it was no big deal and I could adjust it later. I even took a photo before adjusting it, and a photo of the spot where I planned to change the resistor values.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

But reality turned out to be both harsh and completely absurd. The ingenuity of Chinese engineers can be astonishing sometimes.
Let me explain.
I replaced one of the resistors with a trimmer and tried adjusting it. After setting it to roughly the ambient temperature, I started heating the heatsink.
But the value on the screen changed by no more than a couple of digits. O_o
My first thought was that the sensor was faulty; my second was that it wasn’t the right sensor at all.

ZXY6020S, or the next chapter in the story of a powerful DIY bench power supplyZXY6020S, or the next chapter in the story of a powerful DIY bench power supply

But it turned out I had simply read the datasheet carelessly.
Now pay attention as we try to understand what the Chinese engineers came up with.
The screen displays abstract numbers in the range 0–255.
What's more, these numbers vary inversely with temperature: the higher the temperature, the lower the value.
They change over a very narrow range.
But the datasheet says this is a feature: to find out the temperature, you have to calculate it from a baseline of 50, then work out the inverse relationship, assuming a certain number of values per degree.

Can you imagine this process? Someone wants to know how hot the heatsink is, so they use the relationship between the values and temperature to calculate it.
And automatic shutdown depends on this, too. I was shocked.
Fine, they skimped on a proper sensor—not even a thermistor—but why not put all this in the firmware?

While figuring out how the temperature measurement worked, I found that to change the values on the screen across the 0–255 range, you have to change the input voltage from 0 to 3.3 V.
In other words, it simply measures the full voltage at the ADC input and scales it to an 8-bit resolution.

After that, I started looking for a convenient temperature sensor.
At first I wanted to use the same diode or a thermistor, but I wanted to keep the sensor connected between the ADC input and ground. That meant I would need an inverting scaling amplifier with an offset. That's hard enough to say, let alone build.
All the options were bad and completely unacceptable to me.
I wanted a simple, convenient solution—and, most importantly, one that could be replicated.

I found a solution: there are dedicated analog temperature sensors that output a voltage in the 0–1 V range as the temperature changes from 0 to 100 degrees. I thought that was incredibly convenient for this application.

Another trip to the market, another haul of odds and ends.
1. I bought a sensor (a little over a dollar), a couple of op-amps, and a trimmer potentiometer.
2. The sensor's pinout has the power pins on the ends and the output in the middle.
Just to be safe, I soldered a capacitor across the sensor's power pins, right onto the sensor leads.
3. I soldered two of the sensor's leads into the board and connected 12 V from a capacitor on the board to the third. (Before that, I'd soldered a TVS diode there.) I fed the power through a 10 Ω resistor to reduce the 12 V PWM noise, at least a little.
4. I drilled out the existing hole to 5.5 mm, filled it with thermal paste, and put the board back in place.

ZXY6020S, or the continuing story of a homemade high-power bench power supplyZXY6020S, or the continuing story of a homemade high-power bench power supply

I didn't want to publish photos of the failed version at first, but since I took photos while reworking it, I might as well include them.
My first attempt used a TL071 op-amp. It's a single-channel amplifier, which was more convenient for me, but it didn't work.
I just wanted to amplify the sensor voltage by some arbitrary amount—say, 5×—and then use a trimmer potentiometer in a voltage divider to get the value I needed.
The op-amp would be next to the sensor, while the divider and trimmer would be next to the processor.

By the way, two ground wires connect the control board to the power board: one carries the power current, while the other is only for the sensor. That's exactly the right approach for accurate measurements. The voltage drop on the power ground doesn't affect the sensor signal.

So, here's what I did.
1. I prepared the amplifier IC and soldered on a couple of resistors.
2. I cut the signal trace on the power board.
3. I soldered in the IC, taking power directly from a pin on the nearest NE555 IC, and connected the output to the cut trace.
4. I soldered the trimmer potentiometer in place of the resistor divider on the control board, leaving the capacitor in place (I soldered the trimmer leads to it).
The trimmer's third pin is connected to the output from the power board through a fixed resistor.
With the trimmer installed as shown in the photo, turning it clockwise increases the readings; turning it counterclockwise decreases them.

ZXY6020S, or the continuing story of a homemade high-power bench power supplyZXY6020S, or the continuing story of a homemade high-power bench power supply

And I got some inexplicable output. Even the voltage at the temperature sensor pins didn't match reality.
I checked the assembly; everything was fine. Checked again—still fine.

ZXY6020S, or the continuing story of a homemade high-power bench power supplyZXY6020S, or the continuing story of a homemade high-power bench power supply

After that, I decided to go with the classic LM358.
The overall circuit ended up looking like this.
The unused op-amp is simply configured as a voltage follower, but I think I’ll put it to use in the future.

ZXY6020S, or the next chapter in the story of a homemade high-power lab power supplyZXY6020S, or the next chapter in the story of a homemade high-power lab power supply

I soldered the resistors directly to the IC pins again.

ZXY6020S, or the next chapter in the story of a homemade high-power lab power supplyZXY6020S, or the next chapter in the story of a homemade high-power lab power supply

Solder the resulting assembly in the same place and connect it to the same contacts as the previous IC.

ZXY6020S, or the next chapter in the story of a homemade high-power lab power supplyZXY6020S, or the next chapter in the story of a homemade high-power lab power supply

Everything works :))))
At first it showed something arbitrary, but that’s normal.
The adjustment process is very simple: connect a multimeter to the temperature sensor outputs, then use the trimmer to set the same reading on the converter’s display.
For example, 0.3 V on the multimeter means 30 degrees. If it reads 0.26 V, that means 26 degrees.
In practice, I found that although the sensor draws very little current, it still has a slight self-heating effect: after a short while, the temperature rises by 2–3 degrees. It’s nothing serious; you can either compensate with the trimmer or just ignore it.

Now, about the unused op-amp section.
I was hoping the board could control the fan based on temperature, but it simply turns it on when the output is active (when voltage is applied to the board’s output), and also runs it for a few seconds when the board is switched on.
There is a fan speed control feature, but it works in a completely baffling way—or at least I couldn’t figure it out. For example, the fan speed can change slightly when you adjust the overtemperature protection setting. So I plan to modify the circuit in the future, adding temperature-based fan speed control using readings from the installed sensor.

ZXY6020S, or the next chapter in the story of a homemade high-power lab power supplyZXY6020S, or the next chapter in the story of a homemade high-power lab power supply

.

Let's continue the saga of assembling the power supply.
Before connecting the power supplies, it's a good idea to set their outputs to the same voltage.
I decided not to run them at their rated 36 V, but to lower that slightly to 34 V.
That gives 68 V in total, which is more than enough for the 62 V maximum.
You can also use other power supplies, for example 48, 60, or 72 V models.
Another option is to use EATON power supplies. They sometimes turn up at auction after being removed from telephone exchanges (if I remember correctly).

ZXY6020S, or the next chapter in the story of a homemade high-power bench power supplyZXY6020S, or the next chapter in the story of a homemade high-power bench power supply

After finishing the setup, I connected all the necessary wires and bundled them with cable ties, giving things a more or less decent appearance. And since there's a fan nearby, it's better to keep the wires organized into bundles—it makes it less likely they'll get caught where they shouldn't.

ZXY6020S, or the continuing story of a powerful DIY bench power supplyZXY6020S, or the continuing story of a powerful DIY bench power supply

I was very pleased with the case panels: they already have a grid marked on them at 5 mm intervals, which is handy when installing various components and parts.
I installed the fan almost at the very bottom—5 mm from the bottom, to be precise—but it would be better to raise it by 5 mm, since the wire bundles didn't fit underneath very well.
By the way, there's a screw that goes into the center of the case bottom, but I didn't use it so I wouldn't pierce any wires.

ZXY6020S, or the continuing story of a powerful DIY bench power supplyZXY6020S, or the continuing story of a powerful DIY bench power supply

For the power supply, I used the SUNON 12 V fan I'm familiar with, model EE80251S1-A99, with an airflow rating of 68 m³/h and a claimed noise level of 33 dBA.
All in all, it's a pretty good-quality fan that costs about two dollars.

Since I bought a black protective grille for the fan, and the rear panel is also colored, I chose black fasteners as well.
I was out of the special self-tapping screws, so I had to improvise. I used hard drive screws, and instead of nuts, I used case standoffs with the matching thread.
I also installed a 230 V power connector and a USB connector on the rear panel.

ZXY6020S, or the continuing story of a powerful DIY bench power supplyZXY6020S, or the continuing story of a powerful DIY bench power supply

A little about the connectors.
1. To connect it to a computer, I used the same type of connector as in this review, and the mounting system is exactly the same too, so there's no point repeating the description.
2, 3, 4. Standard 6.3 mm locking terminals are used to connect the mains switch. For insulation, I used silicone insulators. Since the cable had to be stripped over quite a long section, I restored the protective sheath afterward using clear heat-shrink tubing.

ZXY6020S, or the continuing story of a powerful DIY bench power supplyZXY6020S, or the continuing story of a powerful DIY bench power supply

The mains switch didn't go entirely smoothly either.
I bought a small mains switch I was familiar with out of habit, only to discover afterward that it was rated for currents up to just 3 A, which is clearly too little for the power I'm dealing with.
I had to buy another switch as well. The seller recommended one from Arcolectric, saying it was very high quality—another dollar and a half gone.
At the same time, I bought a third one so I'd have a choice. It's good quality too, but it's a push-button type rather than a rocker switch. It has an indicator light and looks nice, so that cost me another dollar and a half or so. I didn't like it all that much, though; it's pretty stiff.

ZXY6020S, or the continuing story of a powerful DIY bench power supplyZXY6020S, or the continuing story of a powerful DIY bench power supply

Test power-up with everything in the case. So far, it all works—or at least pretends to :)

ZXY6020S, or the continuing story of a powerful DIY bench power supplyZXY6020S, or the continuing story of a powerful DIY bench power supply

The next part was supposed to describe the rest of the power supply assembly, but for some reason, when I tried to save it again, I got this message:
Error: Description must be between 200 and 15,000 characters :(
So I had to split the review into two parts.
To be honest, I never set out to write a long review, and certainly didn't expect to see that message. I was simply describing the boards and my struggle with Chinese engineering, but the review turned out to be really long.

At this point, though, I can sum up my thoughts on this product.
I won't list pros and cons; I'll just give a brief summary of how I see this device.

The board is perfectly decent, and the price is excellent (at least, I haven't seen it cheaper anywhere).
What's more, it works right out of the box. They even included a USB-RS232 converter, which I wasn't expecting.
I was very pleased to see the improved power supply design; it should be more reliable than previous versions.

Of course, there are a few shortcomings, most likely due to cost-cutting during production.
I described the modifications the board has undergone above. Some are best done right away, for example:
Increase the width of the PCB's power traces (almost free).
Resolder the leads of some components (your mileage may vary; they might already be soldered properly).
It's a good idea to replace the 63 V output capacitors with 80 V or 100 V ones. These are probably the only components installed with absolutely no headroom.

Some modifications are more cosmetic in nature, for example:
Replace all the small electrolytic capacitors with higher-quality ones.
Add an extra capacitor to the power board.
Add protection components to prevent damage to the analog circuitry and processor if the input PWM regulator fails.

As for outright design flaws, the only one I can point to is the very poorly thought-out temperature sensor. I can't understand how they could have designed it this way.
It's hard for me to comment on the output power, since I don't have the means to test this board at those power levels. However, I've occasionally seen people online say that the board works fine, and the previous power supply is still working to this day.
Still, I wouldn't run it at full power for extended periods.

I'm not going to try to convince anyone to buy this board—I have nothing to gain from that—but I will say that I'm happy with it so far. Time will tell how it holds up.

Since I couldn't fit everything into a single review,
To be continued


The product was provided by the store for review.
$71.56
Go to store
This page was found when searching for:
платы сэндвич, мощный лабораторный блок питания своими на atmega, 9, доработка, xy6020l, lm2903 datasheet, xy6020l калибровка, xy6020l dc-dc можно ли использовать как лбп, зарядное устройство для автомобильного аккумулятора из готовых китайских плат, 7, powerizer корпус блока питания, 13, xy6020l инструкция на русском скачать pdf, xy6020l доработка, kirich 6020l, принципиальная схема xy 6020l, xy6020l, xy 6020 l инструкция на русском pdf, esp32 xy6020l, xy6020l uart подключение, xy6020l протокол обмена, xy-6020l, вывод данных лабораторного блока питания на экран телефона, обзор xy 6020, распиновка панели xy6020l, сбросить настройки на преобразователи 6020l

Questions and answers

What are the stated specifications of the ZXY6020S converter?

The article gives maximum output values of 62 V and 22 A, equivalent to over 1300 W. The author sets the power supply's maximum power limit to 700 W.

How much power can the ZXY6020S provide at 14 V and 28 V?

With the supply limited to 700 W, the author expects over 300 W at 14 V and over 600 W at 28 V.

What is the author's conclusion about the DIY ZXY6020S supply?

The author is pleased with the board and finds it convenient, but could not test it at maximum power and would not load it at full power for extended periods.


This model is included in the summary table: Comparison of adjustable converters for a bench power supply

The figures from this review are in the measurement database: Converters

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments2

Comments are published in their original language.

  1. Anton
    2 June 2019 21:58#1
    ZXY6020S, or the next chapter in the story of a DIY high-power bench power supply
    Подскажите пожалуйста, не удалось ли идентифицировать "транзистор линейного стабилизатора 54 Вольта".
    У меня уже давно трудился данный преобразователь, но после очередной сборки / разборки отломилась одна из ног...
    Пытаюсь найти замену, но ничего похожего не гуглится...
    +1
    1. 4 June 2019 19:58#2
      Да я как-то дальше и забросил поиски информации.
      В принципе скорее всего какой-то "Дарлингтон" на напряжение порядка 100-150 Вольт.
      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister