Mean Well HDR-100-12N power supply, the fifth of six
Both power supplies use the same form factor and have the same output voltage—though I’m getting ahead of myself. More on that in the review.
As I said, both power supplies are designed for DIN rail mounting in electrical panels. In this case, we’re talking about ordinary household panels, although they can also be used in industrial applications, with some limitations.

The similarities start with the packaging: both come in the familiar Mean Well cardboard box with a window.

All the key information is printed on the top cover of the power supply: input and output voltage, output current, connection recommendations, and a brief note about the manufacturer.
There’s also a power indicator LED on top.

More detailed information is available in the manufacturer's description, but as usual, I’ll include the most important details here.
The HDR-60 came in 6 output voltage options; this one has a slightly more limited selection of 5. The 3.3 V models are gone, leaving only 12, 15, 24, and 48 V.
However, only the 24 and 48 V versions deliver the full 100 W stated in the model name.
The 15 V model delivers 97 W, while the 12 V version manages a modest 90 W.

You’ve probably noticed the somewhat odd model list, which includes pairs with and without an N at the end of the name.
There are two very similar versions. According to the manufacturer, the model without the N has a narrower output voltage adjustment range, and its output power is also about 5–8% lower.
Curiously, the seller offering these power supplies charges the same price for every model.

Like the HDR-60, this power supply has plenty of ventilation openings on the top and bottom edges of the case.

There’s an opening near the output terminals for access to the trimmer that adjusts the output voltage. The bottom of the case also has a latch for securing it to the DIN rail. If the cases weren’t different widths, you might think these were the same power supply.

Speaking of width, the previous power supply was 3 modules wide (52 mm). The one under review is one module wider, at 70 mm.

The drawing gives the full case dimensions. Even without it, though, you can see that the case cross-section is roughly the same size as a standard circuit breaker.

The power supply is just as easy to open: two latches on the left and two on the right, and that’s it.

Inside, the power supplies are much less alike than they are on the outside. The heatsinks are designed differently, and the HDR-100 has a few more components.


The input has a full mains filter consisting of two common-mode chokes and an X capacitor.

1. A thermistor is installed at the input to limit inrush current. A 15 Ω resistor is also connected in parallel with it.
2. A varistor is tucked between the X capacitor and one of the chokes, with a fuse next to it.
3. As in the HDR-60, the high-voltage transistor is hidden between the heatsink and the input capacitor. As far as I could make out, it’s an IPL60R299CP.
4. But there’s also one key difference: this model has a thermistor to protect the power supply from overheating; the HDR-60 didn’t have one. The thermistor is covered with heat-shrink tubing and monitors the air temperature inside the power supply, rather than the temperature of any particular component. The capacitor powering the PWM controller is protected by the same kind of tubing just to the right.

The input capacitor is made by Nippon and has a capacitance of 150 µF. The HDR-60 had a 120 µF capacitor, which is actually more when you compare capacitance relative to power.
The high-voltage transistor’s heatsink is glued to the transformer. It’s a rather basic solution, but it holds firmly.

The output section of the power supply. I should probably point out the rather bulky transformer and the extra insulation on some components (and the transformer itself) using thin fiberglass board.

There is a fairly significant difference at the power supply output, though. First, it uses a synchronous rectifier with a CSD19531KCS transistor instead of a diode assembly like the HDR-60. The special cutout in the heatsink for the wire made me smile a little.

1. The HDR-60 had three 1000 µF output capacitors; this one has a pair of 1800 µF capacitors and one 1000 µF polymer capacitor. The conventional capacitors are made by Rubycon, and the polymer one is from Lelon, with a specified ESR of 10 mΩ. As I understand it, the polymer capacitor takes most of the ripple current, while the conventional ones handle the rest.
The output choke with two windings is also visible nearby.
2. A 100 µF capacitor is installed after the choke, just as in the HDR-60.

The interwinding noise-suppression capacitor. But what caught my interest here wasn't that; it was the space for an additional board to the right. Apparently, there are more "advanced" versions of this power supply.

The board looks well made, with protective slots, and it has been cleaned very thoroughly.
However, during testing I did find a problem, which I'll discuss at the end of the review.

As with the HDR-60, the output current is monitored on the secondary side, so there is a current-sense shunt; short-circuit protection is implemented on the primary side.

1, 2. The primary-side circuitry is almost identical to that of the HDR-60. It uses the same PWM controller and has the same circuit for limiting the PWM controller's supply voltage. The component values differ slightly, and an RC network has been added in parallel with the auxiliary-winding diode.
3. There is no familiar TL431 here either; a separate controller does the job instead.
4. And, of course, the synchronous rectifier controller.

The block diagram is also identical to that of the HDR-60, although the power supply under review has thermal protection, which for some reason isn't shown here.

The schematic is in many ways similar to the HDR-60, but it also includes some noticeable changes. These are especially apparent in the output section, which uses a synchronous rectifier, and in the slightly modified output-voltage controller circuit.
Although I did my best to copy the schematic carefully, it may still contain errors, so please forgive me in advance.

Before moving on to the tests, a couple more words about the power supply's construction.
As with the HDR-60, the manufacturer used the same set of terminal blocks: a standard one at the input and an "elevator-style" one at the output. I didn't like the input terminal block last time, and it's no better this time around.

The product description calls this a power supply with an extended output-voltage adjustment range.
But I'd put it a little differently: the model without the N has a narrow range, while the one under review has a perfectly standard one. In fact, it's even slightly narrower than the HDR-60's, where I can adjust the output voltage from 9.9 to 14.7 V.

First on the main test list is checking how the output voltage varies with load current, along with efficiency and power factor.
For this, I use two multimeters, an electronic load, a wattmeter, a piece of paper, a pen, and, for the low-voltage tests, a step-down transformer as well.

In terms of efficiency, the power supply performed quite well, even exceeding the manufacturer's rating. However, as the load increases, the output voltage drops noticeably more than it does with the HDR-60. At maximum load, the voltage sagged by about 110 mV, or around 1%. That's not particularly critical and is within the specified limits, but the HDR-60 still performed noticeably better despite having almost identical circuitry.

Measuring the output ripple. This test was also performed at two input voltages: 225 V and about 110 V. A filter consisting of a 47 µF electrolytic capacitor and a 100 nF ceramic capacitor was connected ahead of the oscilloscope probe.

At no load, there is a small sawtooth ripple, like on the HDR-60, but with a much lower amplitude.

Most of the oscilloscope traces are hidden under the spoiler.
Comparison screenshot at 100% load.
1, 2. High- and low-frequency ripple at 225 V
3, 4. The same at 110 V
I can say unequivocally that the power supply under review is less “noisy.” The HDR-60 had a ripple amplitude of up to 100 mV, against a specified 120 mV; here it’s only about 50–60 mV.

The safe operating area recommended by the manufacturer allows for a slightly wider ambient temperature range: at 230 V, it can be operated at temperatures up to 50 degrees. However, its input voltage range is narrower: the HDR-60 could be loaded to 100% starting at an input of 100 V, while this one can only do so from 115 V.

Still, the graph above didn’t stop me from testing the power supply under fairly demanding conditions, with a load current of up to 8 A at 225 V and 7.7 A at 107 V.
I covered the power supply with its lid to worsen its thermal conditions, and the internal temperature exceeded the recommended operating range.

Component temperatures were roughly comparable: some ran hotter, others cooler. The input bridge rectifier was the first—and only—component to exceed 100 degrees, at the lower input voltage.
At an input voltage of 230 V, I think I could have raised the output current a little more, but the synchronous rectifier transistor would most likely have been the first to overheat.
Each test lasted 20 minutes, for a total of 1 hour 20 minutes per stage.

Thermal images taken at the end of each test stage.
230 V

108 V

Since overload current is measured on the output side, it doesn’t depend on the input voltage. I demonstrated this in the previous review, so I’ll give the results only for an input voltage of 230 V.
The power supply shut down at a current of 8.737–8.742 A. The output voltage remained stable right up to shutdown, as you can see in the photo on the left. Output power was about 103 W.

The same process, shown in motion.

And the final test: response to a short circuit. It passed with flying colors.

While preparing the review—or, more precisely, double-checking a few details in the schematic—I came across a manufacturing defect.
I was checking the connections between components and noticed there was no continuity to one of the capacitors, even though I could clearly see a trace leading to it. I investigated and found that the capacitor hadn’t been soldered in. Glue had seeped onto the pad during component placement and prevented the solder from making a connection.
The capacitor is connected between two pins of the voltage monitor. The power supply had performed very well in all my tests, and as far as I know, the manufacturer also tests it.
So, even well-known manufacturers can have defects.

Comparison of three power supplies: HDR-60, HDR-100, and SDR-120

Another comparison: HDR-60 and SDR-120.

Video version of the review
Leaving aside the issue with the unsoldered capacitor, I’d say I liked this power supply a little more than the HDR-60. Mainly because it has less output ripple despite its higher output power.
However, its overload headroom is lower. The HDR-60 kept running at 6 A, which is 72 W or 130% load, while this one won’t go beyond 110–112%. Although, judging by its behavior, I’d say its actual headroom is greater than the limit set by the manufacturer.
The design is also a little better: it has a synchronous rectifier, a polymer output capacitor, a larger transformer, and thermal protection.
That’s all from me. As always, I’m looking forward to your questions—and just a general discussion of HDR-60 vs. HDR100.
LD-10012HDR ,kjr gbnfybz c[tvf gjlrk.xtybz, 8, mean well ts-700-248b фото схемы, meanwell drc обзор потребление холостого хода, схемотехника mean well, 4, 1, 2, mean well drc-100b схема, mean well s 60-12 схема, https://www.kirich.blog/obzory/bloki-pitaniya/568-blok-pitaniya-mean-well-hdr-100-12n-pyatyy-iz-shesti, hdr-100-24 хема принципиальная, MEAN WELL RPT-60А ghbywbgbfkmyfz c[tvf, meanwell dr-100n-r2, mdr-20a-r5 схема, шим контроллер для блока питания ноутбука, блок питания mean well dr-120-24 схема, источник питания hrp 100 24 mean well схема подключения, szjwdy 100a1 2015 5 26, схеа блока drc 100a r5, схеа блока drc-100a-r5, источник питания 5vdc 12a rs 78 5 mean well, szjwdy 100a схема принципиальная, импульсный блок питания sd 100n r5vai, meanwell hdr 100 24 обзор, блок питания Mean Well, блок питания 12 Вольт, тест блока питания, схема блока питания, обзор блоков питания
Questions and answers
What output power did the Mean Well HDR-100-12N deliver in testing?
Its output power was about 103 W during the test.
How did the Mean Well HDR-100-12N handle a short circuit and overload?
It passed the short-circuit test. The author could not get more than 110–112% overload, though the actual headroom may be greater than the limit set by the manufacturer.
What defect did the review find in the Mean Well HDR-100-12N?
One capacitor was not soldered: adhesive covered its pad and prevented a solder joint from forming. The power supply nevertheless passed the author's tests well.
This model is included in the summary table: Comparison of power supplies: ripple, efficiency, and temperature rise
The figures from this review are in the measurement database: Power supplies
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments2
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.