/       /       /    Delta AFB0712SH fans, another attempt
Support the project on Patreon


Delta AFB0712SH fans, another attempt

$3.33 (без учета доставки)
Go to store
This is already my third attempt at buying fans on AliExpress, and this time I wanted to try my luck with “Original For Delta AFB0712SH.” I chose carefully, but...

As a reminder, to keep up with new posts on the blog, I recommend following me on Instagram, where I’ll post notifications about every new article and maybe write about something interesting too: link to my account

You can also subscribe to updates and new articles on the Telegram channel - https://t.me/KirichBlog

I ordered two fans to try out, for a total of $13.58, or about $6.80 each including shipping. One thing to note about shipping: the seller is crafty. The shipping cost goes up almost in proportion to the quantity, and it looks like about 40% of the price is actually built into shipping. The listed price is $3.33, with $3.68 shipping; if you buy two, it’s $3.33 + $3.33, with $7.37 shipping.

I have absolutely no complaints about the packaging. This gets a thumbs-up from me: a foam box, with each fan in its own bag and wrapped in bubble wrap as well.


They look neat, but even at a glance it was immediately clear that these weren’t the ones shown on the product page. I’ll explain the difference later.


Judging by the quality of the plastic, I can say the fans are clearly genuine, but the label is definitely fake. I’ll also point out that the company name is molded into the housings, which further confirms they’re original.
The connector has three wires, but it isn’t the original one, since the fans themselves have four wires and the fourth has been cut off.


The store photo showed a wire with a connector soldered on separately, and the label was clearly different.


It’s easy to find the datasheet for these fans online. The exact suffix is a little unclear, since there are two more letters after the model name, but I went by the name and the stated current. For this model, it’s 0.76 A, as listed in the datasheet and on the fan housing.
The manufacturer’s page lists the current as 0.65 A; that’s not a mistake.


The datasheet lists 0.65 A as the nominal current and 0.76 A as the maximum. Since the supply voltage range is 5–13.8 V, it’s clear that 0.65 A is specified at 12 V and 0.76 A at 13.8 V.


Let’s connect it.
1. It starts at around 3.5 V; at 4 V it spins with no trouble at all.
2. At 5 V, we get about 0.5 W of power.
3. But at 12 V, the current is only 0.231 A, even though 0.65 A was promised.
4. Even if I raise the supply voltage to 15 V, I still get only 0.285 A.


I immediately noticed something interesting that I hadn’t seen before: if you raise the voltage further, the current and power both decrease.


1, 2. If you block the air outlet or inlet, the power consumption drops. And if the fan is running in forced mode, blocking the outlet reduces power by about 10%.
3, 4. I also noticed that even the position relative to the impeller axis has a slight effect on power.


The second unit had slightly higher power, but I wouldn’t say the difference was significant.
But this let me test my theory: I started changing the voltage gradually and found that the maximum power point is at around 14.7–14.8 V.


Let’s see what’s inside. I’ll take apart the second unit. By the way, for some reason its yellow wire wasn’t sticking out.


There are two bearings inside, and no complaints here either: this is clearly not a cheap sleeve-bearing version, and the bearings are quite large.


A dedicated controller is used for control, and the circuit board looks as if it’s been washed.


There’s also some kind of marking on the housing beneath the board, which is further evidence that it’s genuine.


An online search turned up the datasheet for the controller used here.


The datasheet clearly shows a maximum of 17 V, and the operating voltage can easily be raised to 16 V. I usually run my fans in forced mode at 15 V, so that’s perfectly fine.


But I was more interested in the circuit. You can see here that the chip can monitor the current draw, and at first I thought that was what caused the power to drop at higher voltages. But reading the datasheet showed that the maximum current with a 1 Ω shunt is 0.48 A. There are two 1 Ω shunts here, so the maximum current could be 0.96 A, which is clearly lower than what we have.


Further analysis of the circuit showed that it has an input for a temperature sensor. I suspected that too, but there’s no sensor on the board. Instead, there’s a voltage divider in its place. The circuit is slightly different, though: a capacitor has been added in parallel with the upper resistor, along with a diode between the PWM transistor and the temperature-sensor input. But it’s connected so that it’s off when there’s no PWM signal and has no effect on the circuit.


To start with, I decided to simply cut off the upper part of the divider so the controller would think the temperature sensor had heated up and its resistance had dropped significantly.


After that, a few things changed. First, when I raised the voltage above 15 V, the power was no longer limited.
Second, a turn-on voltage threshold appeared. Before, the fan started at 3.5 V; now it starts at 7.5 V, and naturally goes straight to the corresponding power level. If I lower the voltage, it keeps spinning at 7.4 V, but more slowly; lower still, and it shuts off.


I tried reading the datasheet and found that you can disable the fan’s thermal protection. For some reason, this requires connecting the internal regulator’s output to the power input. That seemed like complete nonsense to me. But I also noticed there’s a thermostat function...
The datasheet is a bit odd in general, and even has errors. For example:
Thermal shat down





So I decided to try a different approach. I repaired the cut trace and connected a variable resistor in parallel with the lower resistor in the thermal control divider, then started adjusting the resistance.
It turned out that shorting the lower resistor enables another operating mode: the fan starts at roughly the same 4 V, but switches off at 8–9 V.
In any case, after some trial and error I found a resistance that gives maximum power while still letting the fan start at 3.5 V. I needed to solder about 1.8 kΩ in parallel with the original resistor, but I didn't have one, so I used 1.5 kΩ.


The result:
The fan starts at 3.3 V and runs as before at 12 V, but at 15–16 V its power is now 5.2–6 W.


Now, about what I was looking for when choosing a fan.
Besides the power and size, I wanted one whose product page showed the CE mark on the label. The fans I received have it too, but there's “one catch.”
Fortunately, the fan datasheet shows all three label variants.


1. The one shown by the seller.
2. What the label is supposed to look like; here it matches the seller's photo.
3. What I received. The country of manufacture is different, but that's perfectly normal.
4. What the label is supposed to look like for this country; the differences are obvious.


Besides the minor differences, the CE mark stands out. There's the genuine European mark, and then there's the so-called China Export mark. To put it very simply, it's roughly like the difference between a national standard and a manufacturer's specification, but in reality there are many more differences. For example, according to the datasheet, these fans were never made with the China Export mark.




Conclusions.
Another disappointment. Again, I have no complaints about the packaging or appearance, or even about the build and operation in general, but once again I got a fan with clearly less power than advertised.
So, another case of deception: the seller is selling different fans under the guise of one model, even if they're branded and perfectly decent quality. I don't understand the point of this idiocy. Surely there are people who want exactly the fan I received, with these same specifications, but they won't buy this one because, according to the listing, it's clearly more powerful.

I recommend these fans, provided you're happy with the power shown in this review. I have no complaints about the overall product quality.

By the way, the seller refunded almost the entire order amount for the fake “Sunons,” excluding shipping, and did so without any hassle—but, what's more, using some new method. Before, it worked like this: you agreed on compensation with the seller (if you could reach an agreement), opened a dispute, and got your money back. This time I asked, “OK, should I open a dispute?” and the seller replied, “I've already refunded you, just wait.” And sure enough, a few days later the agreed amount was back on my card without me opening a dispute, but as AliExpress funds. The seller offered a larger amount (the full price of all three fans), but via PayPal, which I can't use.

So what should I do here—open a dispute? What do you think? It's starting to get annoying when you order one thing and end up getting almost the same thing every time, with 2–3 times less power.

That's all for now. I hope this was useful.
$3.33 (без учета доставки)
Go to store
This page was found when searching for:
вентилятор avc datasheet

Questions and answers

How much current do the Delta AFB0712SH fans draw at 12 V?

The measured current was 0.231 A, well below the stated 0.65 A.

Can the power of the Delta AFB0712SH fans be increased?

The author modified the thermal-control circuit by adding a 1.5 kΩ resistor in parallel with the divider’s lower resistor. The fan then drew 5.2–6 W at 15–16 V and started at 3.3 V.

What is the review’s conclusion about the Delta AFB0712SH fans from AliExpress?

They are neatly made and have two bearings, but their performance does not match the listing: the seller sent a different, lower-power version.

The figures from this review are in the measurement database: Other devices


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments2

Comments are published in their original language.

  1. 2 July 2023 01:24#1
    Можно попробовать заказать не Дельту/Санон, а менее широкоизвестные брэнды. Возможно, их не так активно будут подделывать.
    12v, 0,7A:
    https://www.aliexpress.com/item/32721784673.html - 7020
    https://www.aliexpress.com/item/32721780236.html - 7015
    0
    1. 2 July 2023 02:07#2
      Обзор AVC у меня был первым, если коротко, то суть та же самая.
      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister