/       /       /    74HCT125, SGM6130, and a Little About Repairing a 3D Printer Board
Support the project on Patreon


74HCT125, SGM6130, and a Little About Repairing a 3D Printer Board

$3.36
Go to store
This story began around February this year, when two 3D printer boards came in for repair along with the power supply. The power supply turned out to be a relatively easy fix, but the board repairs dragged on for quite a while. I recently received the missing component, though, so I can put together a short article about it.

A reminder: to keep up with new topics on the blog, I recommend following me on Instagram. I’ll post notifications about all new topics there, and might also write about something interesting from time to time — link to my account

You can also subscribe to updates and new articles on the Telegram channel — https://t.me/KirichBlog

I’ll say right away that the delay wasn’t my fault: one of the components I ordered took more than 3 months to get to me from China. To be precise, I ordered the chip at the end of March. The seller shipped it quickly, but with a tracking number that can’t be tracked in Ukraine. The part seemed to be on its way, but then it stopped moving. I waited until the end of May and ordered it again. Then came the second problem: shipping had originally cost 44 cents with super-economy delivery. I didn’t want to pay extra for expensive shipping, so I had to add a few more parts to the order, bringing the total to $7, on top of the component that cost 70 cents. More on that later.

So, I received a couple of printer boards.


One of them had a very simple problem: the UART-to-USB chip had blown, in this case a CH340C. The thing about this version of the chip is that it has a built-in oscillator, and since there’s no crystal resonator on the board, this is the exact chip needed.
This one’s easy.
1. Take a new chip and let it acclimatize next to the board.
2. Desolder the old one.
3. Wash the board.
4. Solder the new one in, then wash the board again.
That’s it :)



The second board, though, wasn’t so straightforward, and the board itself is noticeably more complex.


At first glance, there’s a chip with a hole in it and a charred capacitor.


1. There’s almost a short at the power converter’s output.
2. I desolder the capacitor, and the resistance goes up.
3. I desolder the chip with the hole in it, and the resistance goes up some more.
4. Further troubleshooting reveals an almost-short in the circuit of the MOSFET switching one of the outputs, presumably the heated bed. I desolder the transistor, but the resistance is still clearly too low.


Further troubleshooting showed that the output of the 74HCT125, which controls this transistor, had blown.



After diagnosing the board, I had a small pile of components:
74HCT125
SGM6130
CTD03N005
47/6.3V capacitor


And this is where things got interesting.
The SGM6130 is basically just a DC-DC controller, but as they say, “there’s a catch”: its specifications and pinout.
The key point is that this chip supports an input voltage of up to 28.5 V, while the board is powered by a 24 V power supply. Judging by the evidence, this is exactly the chip that blew when the power supply started to fail. There’s very little headroom.


I looked around online and found that the only offline option with this pinout was the XL1853, but unfortunately it’s rated for a maximum of 23 V. Other chips met the specs, but had a different pinout.
In the end, I had to order the SGM6130 from AliExpress. There’s also an updated version, the SGM6132. It’s identical except for the frequency: 1.4 MHz instead of 385 kHz.
Another problem was that nobody usually sells them individually. I found a lot of 5 at the lowest price, and that’s the one I ended up waiting more than 3 months for in total.


By the way, the Voron store, where I saw the XL1853, incorrectly lists its maximum voltage as 32 V instead of 23 V. Be careful and always double-check.


The 74HCT125 situation was a little better: they’re available locally, but there was another catch. I needed a chip in a TSSOP-14 package, and that was another disappointment. I had to order it from AliExpress too. Again, it was a lot of 5, but the price was lower, $2.07, and shipping was free. Also, there were no delivery problems.


I also ran into a problem with the CTD03N005 transistor. It broke during troubleshooting: I wanted to lift the gate lead slightly, but it simply snapped off with very little force. I don't know what caused it, but in the end I had to track this one down too—and it's no ordinary transistor.
Operating voltage: 30 V; on-resistance: 3.7 mΩ at 10 V and 6 mΩ at 4.5 V; current up to 85 A.


I had to do some searching, and I really didn't want to order it from AliExpress, since the odds of getting a counterfeit are practically 100%.
Anyway, I found a replacement at Kosmodrom: IRLR8743PBF. In my opinion, it's actually a bit more interesting.
Same package, also rated for up to 30 V, but it can handle up to 160 A, with an on-resistance of 2 mΩ at 10 V and, more importantly, 3 mΩ at 4.5 V.
The thing is, this transistor is driven by a 5 V logic level, so the on-resistance at that voltage is the one that matters.

So it comes out about twice as good, and the price is pretty reasonable too.


The capacitor was the easiest part. I ordered it along with the transistor from the same store, Kosmodrom. There were two options: standard and LowESR. I chose the latter.

I finally got the envelope with the missing parts recently—or, to be precise, the one missing part. I had to buy the rest as extras; otherwise, the DC-DC chip would have cost a fortune, though I can't say I needed those extras. By the way, the seller had no problem refunding me for the lost package. The only catch is that the buyer protection period is 90 days...


The order included:
1. SGM6130, 5 pcs, $3.36 - link
2. TOP260EN, 5 pcs, $2.18 - link
3. FAN7930C, 10 pcs, $1.53 - link , shipping is free here
4. OB2273, 10 pcs, $0.75 - link

Total cost including shipping: $10.37



All the parts are here, so it's time to get started on the repair.


Here's a closer look at the components, just in case.


I'm cleaning the board before installing the components.


I'm tinning the underside of the PWM controller and transistor to make them easier to install. By the way, can anyone recommend a good modern flux for soldering components like these onto circuit boards?




I'm soldering the components in place. The biggest challenge was installing the transistor: there's a lot of plastic nearby, making it hard to get in there, and the copper pour seems pretty substantial too. I had to heat it from underneath, then apply more heat from above while installing it.
The PWM controller was a little easier, although I don't think my work looks very neat—which is exactly why I asked about flux above.


Installing the TSSOP-14, on the other hand, was no problem at all. The connectors and other components were in the way again, but even with the SH-K tip, everything went smoothly. Though, why do I say “even with” the SH-K? It turned out to be an almost universal tip, and I've nearly fallen in love with it. You can solder a TSSOP-14 with the sharp point, or use the full width to heat one entire side of the “many-legged” chip at once.


I apply the standard 24 V, and get 5 V at the output. Everything looks good. By the way, the board's owner was incredibly lucky that its main power came from USB rather than the DC-DC converter—there's a dedicated switch for that. Yes, there's a 5-to-3.3 V regulator, but I doubt it would have helped if 24 V had reached its input.
So only the 74HCT125 and the transistors it controls were powered by the DC-DC converter here. But if the jumper had been in the other position, 24 V would have gone to both the controller and the drivers. Basically, the board would have been a write-off.


I test it under load, starting with 10 Ω (0.5 A) and 25 V at the input. No problems; the chip stays cool.


Then I raise the input voltage to 26 V, increase the load to 1 A, and let it run like that for about 20 minutes. Still no problems. The diode gets hot, the inductor gets hot, and the chip is barely warm.


A little later, one of the readers suggested an alternative to the SGM6130 chip—many thanks for that—and it's the TD1583. It seems to be a higher-voltage equivalent of the XL1853, since they're fully pin-compatible. SGM6130 is compatible with them too, but it needs a bootstrap capacitor, an external compensation network, and a few other things. The corresponding pins on the XL1853 and TD1583 are simply unused and marked NC.
But another important point here is that the TD1583 is available locally and is relatively inexpensive.



Conclusion.
Unfortunately, it’s very inconvenient for me to test the board fully, so I’ve sent it to its owner for further testing and am waiting to hear back.
At least I was able to test the SGM6130 and, indirectly, the 74HCT125. The DC-DC converter wasn’t loaded to 3 A, but the other components aren’t rated for that current either. I think the maximum is around 1.5 A. I don’t want to deliberately burn out the board just to test it, and the chip also needs cooling, so a toner-transfer PCB isn’t enough.

All in all, I think it’s safe to buy the SGM6130 from this seller, at least. But I’m more curious to test the TOP260EN chips.


That’s all for now. I hope you found this useful.
$3.36
Go to store
This page was found when searching for:
микросхема rci-6130, вышла из строя 74hc125, sgm6130, https://www.kirich.blog/obzory/radiolyubitelskoe/1183-74hct125-sgm6130-i-nemnogo-o-remonte-platy-3d-printera

Questions and answers

What faults were found on the 3D printer board?

The 74HCT125 output and the SGM6130 DC-DC converter had failed; the board also had a charred capacitor and a faulty power transistor.

How was the SGM6130 tested after the repair?

It was first tested at 25 V with a 0.5 A load, then at 26 V and 1 A for about 20 minutes. There were no problems: the diode and inductor warmed up, while the chip stayed barely warm.

What replaced the CTD03N005 transistor?

The replacement was an IRLR8743PBF. The article gives its on-resistance at a 4.5 V logic level as 3 mΩ, compared with 6 mΩ for the CTD03N005.

The figures from this review are in the measurement database: Converters


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments11

Comments are published in their original language.

  1. 7 July 2023 20:57#1
    Супер, прям детектив. Дуже цікаво та корисно.
    0
  2. 8 July 2023 09:47#2
    Добра стаття. Хоч свою Вам відсилай)
    Взагалі цікаво скільки це може коштувати (ну хоч Скільки тут коштувало)
    Але в мене щось з процом.

    Хтось знає, до кого реально звернутись, щоб відремонтували?
    Питав у ремонті телефону - сказали можливо, але ми розбиратись не будемо.

    0
    1. 9 July 2023 11:16#3
      С процом може бути все просто , перекинути новий :) я так ст-лінк відремонтував, замість згорівшого китайського клона, запаяв оригінал стм32, та прошив іншим робочим ст-лінк.
      0
      1. 9 July 2023 11:38#4
        А там у процессора прошивки какой-то своей нет? Ведь перекинуть чип это пол дела, вторая половина чтобы оно потом заработало.
        Или там ставится процессор, а прошивка уже с компа загружается штатно?
        0
    2. 9 July 2023 11:37#5
      Перекинуть процессор я вам скорее всего смогу, но вы уверены что проблема только в нем? У меня сложность потом проверить.
      0
      1. 16 July 2023 01:58#6
        От як раз певен що не лише в ньому)
        кілька затемнілих конденсаторів, резисторів.

        Фену майже не має (є фігня для термотрубки, але з горем пополам може чіп випаяти)
        але є китайський столик з підігрівом він гарно розігріває. Тому думаю що зможу і сам.
        проблема як раз у розумінні що поруч )

        Але на всяк випадок симптоми опишу, можливо у когось є пропозиції лікувати по скайпу:
        все почалось з розбору єкструдера тому певен що вимкнув і увімкнув мотор, при включеному принтері. Знаю що так не можна і має згоріти драйвер, але не пощастило платі, драйвер був цілий.
        Плата ніяк не ініацілізується компом.
        Наче у КЗ по порту ЮСБ, завтра доповню, перевірю.
        Проц виглядає цілим, гріється при підключенні юсб
        Поруч з процом є кілька смд конденсаторів - потемнілі. 
        0
        1. 16 July 2023 02:02#7
          Возможно у вас пробило чип UART-USB, проверьте, конденсаторы могут иметь разный цвет, бывают совсем светлые или даже белые, бывают темно коричневые, потому я бы на них пока не грешил.
          0
          1. 16 July 2023 23:50#8
            Возможно у вас пробило чип UART-USB
            Есть проблема. Я не вижу UART-USB чип))
            Плата Two Tress skr e3 dip
            f103 камень. на гитхаб есть пдф, со схемами, что касается юсб:
            IRLML2244 - MOSFET
            NUP2114UCMR6T1G - сборка диодов.
            в принципе попробую все передуть и проц тоже. Но лучше бы фотки показать.Подгоревший там резистор.
            Точнее их там 2шт один норм второй и потемневший и как снятая маска с платы, медь видно. И налёт как буд-то после бахнувшей микросхемы.

            0
            1. 17 July 2023 00:11#9
              Значит USB идет прямо в процессор
              0
  3. 9 July 2023 12:14#10
    Цитата: kirich
    А там у процессора прошивки какой-то своей нет? Ведь перекинуть чип это пол дела, вторая половина чтобы оно потом заработало.
    Или там ставится процессор, а прошивка уже с компа загружается штатно?

    Це не проблема, про потім прошивається через ст-лінк або по по юсб, якщо сн340 стоїть на платі.
    прошивкі різні доступні.
    0
    1. 9 July 2023 12:42#11
      Стлинк как раз не проблема, но через ЮСБ конечно удобнее.

      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister