24 V 100 W power supply with a pretty good result
I was also curious about the differences between these power supplies, though mainly in terms of how they were made rather than their technical specifications, since the units themselves are almost identical. But what will we find this time…
A brief digression.
24 V power supplies are much less common in everyday use than their 12 V counterparts, although they're widely used in industry. They do have a number of advantages, though.
At a still quite safe voltage, for example, they can power LED strips with less voltage drop in the cable and the strip itself (provided the strip is rated for 24 V, of course). These power supplies are also used in small DIY machine tools (search for the CNC acronym).
First, as always, a brief comment on the packaging. Unfortunately, the store didn't take my advice that it would be a good idea to wrap the ends of the package, too.
The board didn't come loose from its bag this time, but it could easily have happened, just like last time.
Rather than refer back to the previous review repeatedly, I'll repeat some of the information here, naturally updating it to apply to this power supply. I think that's the better approach.
First, a few general views of the power supply.
The board looked neater to me, and the transformer seemed a little larger than in the previous version. In fact, though, it uses the same core; it only looks bigger because there's more insulating tape around it :)
The board has the same heatsinks as the 12 V version, except that the diode heatsink is shifted slightly toward the transformer, by just 2 mm. It looks like they made some kind of optimization, though I can't quite see the point of it.
The input has the same screwless terminal block as last time. The input inductor has changed: it's now wound with slightly thicker wire, so it has lower inductance. I think that's unnecessary; the previous version was better.
There's also an interference-suppression capacitor, which is fine.
Brief specifications:
Input voltage: 85–265 V
Output voltage: 24 V
Load current: listed as 4–6 A*
Output power: 100 W (maximum)
As before, the board measures 107 × 57 × 30 mm.
* I think the manufacturer (or the store) has clearly overdone it with the 6 A figure, since 6 A at 24 V is almost 150 W, despite the stated 100 W rating. This power supply is more likely a half-current version of the previous one: 3 A nominal and 4 A maximum.
Drawing with the board's overall dimensions.

A comparison photo of the two power supplies: 24 V on top, 12 V below.
And accordingly, a comparison photo of the circuit boards.
This is where the differences between the power supplies began. They look almost identical from above, but differ noticeably underneath.
What caught my eye right after unpacking was the poor soldering and dirty board.
It looks like someone tried to wash it, but apparently it went through the washer after a pile of other boards, since it has an almost uniform white film.
The solder joints are simply matte; you can see it even in this photo.
The board topology has barely changed, though there are some differences. There is one small improvement, though: the heatsinks are now soldered at both mounting tabs instead of just one, as before.
You can see that one of the diode heatsink's mounting tabs is dangerously close to the negative trace. At first I was a little worried, but then I noticed that the diode is insulated from the heatsink. This worsens heat transfer from the diode to the heatsink, but improves safety and reduces radio interference.
The “optimization” also affected the components. In my previous review, I specifically noted that precision resistors were used. This time, the manufacturer fitted standard ones. I wouldn't say that's a bad thing—precision resistors aren't really needed here—but it's clear the board was “optimized” in ways beyond just moving the heatsink.
As before, it uses a CR6842S PWM controller, which is an equivalent of the better-known SG6842 controller.
I didn't draw a new schematic, since it's almost identical to the 12 V version, but I did include all the changes specific to this power supply.
I happened to notice some strange marks on the board near the high-power SMD resistor. The manufacturer has clearly started cutting costs.
On the one hand, saving money is good; on the other, the main thing is that it doesn't affect quality down the line.
A slightly different transistor is used as the power switch this time: 20N60C3
It's a little better: 650 V instead of 600, 20.7 A instead of 20, and a gate capacitance of 2400 pF instead of the previous transistor's 3000 pF. The load tests will tell us more, but so far, so good.
Last time, I noticed that the PWM controller's supply capacitor had a lower-than-specified capacitance. Everything is fine in this power supply. By the way, people who bought these power supplies after my review later wrote to me that theirs had the correct value too. Since mine had been reworked, I think I just got “lucky.”
The output rectifier is an ST 100 V, 2 × 20 A diode assembly, stps41h100ct.
I wouldn't call that a good choice, since exactly the same assembly was used in the previous power supply, which was rated for 12 V. The software I use to design my power supplies calculates a reverse voltage of 110 V for a 24 V output. Of course, it's designed for a different type of PWM controller. The software includes a safety margin in its calculations, but I always use a 150 V diode in circuits like this.
So you could say the output diode is right at the limit for reverse voltage here :(
On the plus side, they used a higher-voltage capacitor in the snubber, although its capacitance seems a bit high for this voltage to me. Perhaps that also helps protect the output diode to some extent.
As in the previous power supply, the output capacitors have a capacitance of 1000 µF and are rated for 35 V. As before, they aren't name-brand parts: Nichicon FW series capacitors are gold-colored and fairly expensive, and they're marketed for audio amplifiers and the like.
But what's written on the label and what's actually inside are two different things, so of course I measured their actual specs. They turned out to be almost identical to those of the capacitors in the 12 V power supply, so I can conclude that they're the same capacitors in different “packaging.”
Output capacitors — 1100 µF, 30 mΩ (the photo shows two measured in parallel)
Input capacitor — 79.9 µF, 0.162 Ω (this one has better specs than the previous one)
Now for a few drawbacks
First, the more serious one. Instead of a proper Y capacitor, an ordinary high-voltage capacitor is used between the windings. The same thing was true of the small 12 V power supply.
For safety, it's best to replace it.
The less serious issue was a damaged resistor in the diode snubber on the circuit board. It's best not to use the power supply without it, and in any case, I always inspect the board for possible damage before switching it on.
The snubber serves several purposes: it reduces voltage spikes (working alongside the equivalent circuit on the high-voltage side), protects the output diode from short pulses, and reduces interference caused by the diode switching.
The resistor was 5.6 Ω, which I didn't have, so I fitted a 6.8 Ω one. The exact value isn't critical; even 10 Ω would work almost the same.
That's it for the visual inspection. Now for the more “interesting” part: testing the power supply under load.
I was just as interested in this as in the visual comparison.
Summary:
Pros
Almost high-quality assembly, with a few minor issues
Components are of decent quality, but there's no longer any headroom like there was in the 12 V version.
Meets the stated specifications.
Excellent output voltage regulation accuracy.
Low price.
Cons
Issue with the packaging (the store's fault)
Incorrect type of interwinding capacitor.
The output diode assembly has no headroom.
My take: Although the power supply disappointed me a little at first glance—with dull solder joints, poor cleaning, and ordinary resistors instead of precision ones—testing changed my mind.
If you overlook the fact that they used a non-Y-rated interwinding capacitor and that a resistor was damaged (I assume this was an isolated case), this is a pretty good power supply.
I was pleased to see it work properly all the way up to 120 W, despite being rated for 100 W.
Judging by the test results, it can be run at 100 W without any problems.
While writing the review, I noticed that the store had lowered the price of this power supply (the price in the title has already been updated), which may be useful to know. That's partly why I wanted to publish the review sooner.
The product was provided for review by the store.
nes-100-r8 схема, 4, nes-100-r15 схема, s-100f-24 схема блок питания, mean well nes 100 24 пульсация, фильтр питания pf24-100s 100 ватт, бп 24вольта 4а 100 ватт нетянет нагрузку при малом напряжении, https://www.kirich.blog/obzory/108-24-volta-100-vatt-blok-pitaniya-s-neplohim-rezultatom, блок питания s-100-24 схема, nes-100-r17, ибп на 24 вольта схема, инструкция эзишпехера 24 вольта 35 ват, датошит бп ya 100 24 69 ys sw, блок питания za 100 24 схема подключения, схема блока питания arv dr100 24 24v, 4.2a, 100w, универсальный бп 100 ватт, ds 24 9 plus cr6842s, блок питания 24 вольта 100 ватт размеры, nes 100 24 обзор, схему электронную блока питания nes 100 24, схему блока питания nes 100 24, ya 100 24 схема бп для светодиодной ленты, блок питания en 100 24 схема, мс 100 24 108 вт схема подключения, схема nes 100 r1
Questions and answers
How much power could the 24 V, 100 W power supply handle?
In the author's tests, it operated normally at 100 W and remained functional up to 120 W.
What did the author conclude about the 24 V power supply?
Despite dull solder joints, residue from poor board cleaning, and some component-related concerns, the author considered it a fairly good unit after testing. He praised its accurate output-voltage regulation but noted a non-Y interwinding capacitor and an output diode assembly with no headroom.
How did the author reduce ripple in the 24 V power supply?
He soldered four 0.15 µF capacitors in parallel with the output capacitors and directly across the output terminal block. The comparison was made at a 5 A load.
This model is included in the summary table: Comparison of power supplies: ripple, efficiency, and temperature rise
The figures from this review are in the measurement database: Power supplies
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments42
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister





























Comments are published in their original language.