/       /    12 V 5 A power supply, or how it might have been made.
Support the project on Patreon


12 V 5 A power supply, or how it might have been made.

$8.30
Go to store
A review of this power supply from another store was posted here not long ago.
I got a similar power supply, and naturally wanted to see what they have in common and how they differ. I’ll also share my own power supply recipe.
If you’re interested, read on.

I needed this power supply to run a bunch of small chargers, but since that project has been moving at a snail’s pace, I decided to just review the power supply.

I received this power supply a little before the one reviewed by my very capable colleague ksiman appeared, but I was busy and didn’t write about it right away.
Still, after reading the review mentioned above, I wanted to take a look inside the one I’d received.
I was almost certain they were identical, but almost doesn’t mean 100%.
I’ll refer to that review as I go along, and I hope its author won’t mind :)

Anyway, let’s get to the review itself. I’ll tell you what I ended up getting as we go.

The power supply arrived wrapped in a bag. They also included an adapter, though I never figured out what it was for.
Still, they included it, and it might come in handy someday—maybe next time they’ll forget to include one just when I need it.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

The package contained the power supply itself, its power cord, and the adapter mentioned above.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

I have no complaints about the power supply’s appearance; it looks like a power supply.
There’s no ferrite filter on the output cable either—or rather, it looks like there is one, but it’s just plastic inside.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

And here’s the first difference.
The power supply I received is labeled XY1205; in the previous review, it was called XY1205A.
Mine is also marked CM-2 on the bottom, while the other one is marked CM-1. I don’t know what that means, sorry.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

Let’s power it up.
The output voltage is high: 12.54 V instead of 12 V. That’s still within the usual 5% tolerance, but only just.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

The power cord I received was different, with no ground contact.
I hadn’t come across cords like this before, though I knew they existed.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

The cord doesn’t look as thick as a standard computer power cord, though it is round—something like a PVC cable.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

At first I wanted to cut the cord open and see what was inside. But then I thought: what’s the point?
So I simply measured its resistance.
The meter read 1.589 Ω. Allowing for contact resistance, we can round that to 1.58 Ω.
The cord is about 1.08 m long, so the total length of the conductors is 2.16 m.
A simple calculation gives a resistance of 0.73 Ω per meter.
Then I checked a table to find the corresponding wire cross-section: a whopping 0.024 mm².
Good thing the cord is easy to replace.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

After that, I decided to take a look inside after all.
It's not that I don't know how power supplies are built. I just enjoy taking things apart :)
These power supplies are very easy to open. Insert a knife blade into the gap between the two halves of the case, then tap it with a small hammer to break the bond between them.
Basically, it's only difficult and confusing the first time. After that, it's only a little harder than unscrewing the screws with a screwdriver. The only downside is that you can put it back together only with glue.

12 V 5 A power supply, or how it might have been made.12 V 5 A power supply, or how it might have been made.

Inside, this power supply is not very different from the one in the previous review, though there are some differences.
The first thing that stands out is the lack of an input filter; it wasn't even designed to have one.
On the plus side, though, the output capacitors are 1000×25 rather than 470×16.
Overall, not much has changed: performance should improve, but interference will increase.
The transformer looks a little different, but its dimensions are about the same.

12 V 5 A power supply, or how it might have been made.12 V 5 A power supply, or how it might have been made.

The power supplies look very similar on the back of the board, but the markings are different: D-32 on mine versus D-26 on the previous one. Perhaps mine was made later and therefore has a different board revision.
You can also see that the snubber capacitor has been moved to the underside of the board. I've never seen that before; they're usually mounted on top and aren't SMD parts.

12 V 5 A power supply, or how it might have been made.12 V 5 A power supply, or how it might have been made.

The power supply is controlled by a 63D12 controller, which is unknown to me.
I won't draw a schematic for this power supply, since it has no significant differences from the one in ksiman's review. Special thanks to him for that work.

12 V 5 A power supply, or how it might have been made.12 V 5 A power supply, or how it might have been made.

The power transistor is the same, 4N60C

12 V 5 A power supply, or how it might have been made.12 V 5 A power supply, or how it might have been made.

Some components have been rearranged, and a protective slot has been cut in the board beneath the optocoupler. This is another clue that this power supply may be a newer revision.
But the input capacitor is still unsecured. Its capacitance is too low for the claimed 60 W output.

12 V 5 A power supply, or how it might have been made.12 V 5 A power supply, or how it might have been made.


Summary.
Pros.
It does work after all :)
The output capacitors are rated for 25 V, not 16 V, although their placement next to the power diode is far from ideal.
It should be suitable for load currents of 3–3.5 A, but to be on the safe side, I'd limit the load current to 2.5–3 A (maybe I'm more of a pessimist :)).
The power supply uses a PWM controller, rather than the commonly seen self-oscillating circuit.

Cons.
It can't be used at 100% load.
No input EMI filter.
Fairly high output ripple.
The cable is no good; replace it right away.
The components inside the power supply aren't secured.

My verdict: the patient is more alive than dead. In other words, this power supply is perfectly usable. And if you also “tune it up” by replacing the output capacitors with low-impedance ones and increasing the input capacitance to at least 68 µF, or preferably 100 µF, it'll be pretty good. This power supply has potential for improvement. I wouldn't recommend a power supply of comparable power that uses a self-oscillating circuit, in any form.
Suitable for powering non-critical loads such as LED strips and the like.

This power supply was provided free of charge by the gearbest store for experiments and testing.

Oh, I almost forgot. At the beginning of the review, I mentioned my power supply recipe.
Anyway, if you've managed to read to the end, check under the spoiler for the rest :)

Install the transformer and output inductor. I'm leaving out the fuse for now; it'll be clear why later.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.


12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

The board is fully soldered. I use 1 mm solder wire with flux; I don't apply any additional flux while soldering. I had the boards manufactured with a HASL finish.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

For the first power-up, I solder a small 15 W bulb in place of the fuse. If the power supply is assembled correctly, it will either stay off completely or glow very dimly.
The output voltage was right where I wanted it straight away, so no adjustment was needed, though having the option to adjust it is still useful.

12 V 5 A power supply, or how it could have been made.12 V 5 A power supply, or how it could have been made.

There was recently a brief discussion about soldering circuit boards.
I took a couple of photos to show what good soldering looks like with most solders.
I cleaned off the flux residue with a cotton pad soaked in acetone.
Overall view

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

A closer look at one section. If you look carefully, you can even see my reflection :)))

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

I designed the power supply for 15 V and 1.5 A, so I'll test it under a 1.5 A load. Even in its current form, though, this power supply can easily deliver 2 A.
There are two output diodes on the board because, ideally, the diodes should be rated for three times the calculated output current. I installed 31DQ10 diodes (100 V and 3 A), since the calculated current was 1.5 × 3 = 4.5 A.
By the way, I've come across counterfeit diodes with this part number before. They run hotter, so be careful.

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

While I was at it, I captured the ripple waveform at the power supply output under this load. The probe's attenuation is set to 1:1.

12 Volt 5 Amp power supply, or how it might have been made.

After testing the power supply under load, I solder on the input and output cables. For my application, the cables will be short and have no connectors.
I also fit the cable grommets right away (it's better to do this before soldering) and secure the cables with cable ties to keep them from being pulled out of the case.
You can never be too careful; better safe than sorry.

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

After soldering on the cables, I coat the board with Plastics-70 protective lacquer. There's a tougher lacquer called Urethane, but I don't use it because it leaves a coating that's too hard.

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

Here's the fully assembled board, ready to be installed in the case.

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

Bottom view. I used almost no SMD components, just capacitors in parallel with the output electrolytic capacitors.

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

I used a Z-34B case—the taller version of this case. The board was laid out specifically for it, so installation requires cutting two slots for the cables and drilling one hole for the LED. Then secure the board in the case with four small screws (it's best to pre-drill 1.5 mm holes in the case's mounting posts).

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

For the final step, drill out the holes in the bottom half of the case and screw the two halves together.
That's it—the power supply is ready.

12 Volt 5 Amp power supply, or how it might have been made.12 Volt 5 Amp power supply, or how it might have been made.

As they say on the Discovery Channel, now you know how it's made—or at least how it should be made.
And of course, the archive with the schematic, PCB layout, and datasheet.

If you have any questions, ask away. I'll be happy to answer.

$8.30
Go to store
This page was found when searching for:
12v 5a xy1205a схема электрическая, xy1205 схема, схемы блоков питания на 12 вольт и 5 ампер, блок 12 вольт 5 ампер, xy1205a схема, схема блока питания af318 4001dt, как сделать 12 вольтовый 5 ампер а блок питания, af330 4001dt схема, переделка smartbuy 12 вольт 5 ампер назначение выводов, схема бп af318 4001dt, af318 4001dt блок питания схема, простой блок питания 5 ампер 12.5 вольт, схема блока питания xy1205, бп xy1205a, блок питания 12 вольт 5 ампер трансформатор, как переделать блок питания с 12 на 5 вольт, как переделать блок питания с 5 на 12 вольт, малогабаритный двухтактный импульсный блок питания на 12 вольт 5 ампер, 12 вольт 5 ампер блок питания китайского производства мой личный рецепт _, af318 4001 схема, штрих фр к переделать блок питания с 24 вольт на 19 вольт, штрих-фр-к переделать блок питания с 24 вольт на 19 вольт, сделать блок питания, переделка блока питания ноутбука, импульсный блок питания 24 вольта 2 ампера своими руками

Questions and answers

What output voltage does the XY1205 power supply deliver?

The measured voltage was 12.54 V with no load and 12.58 V at a 3.75 A load.

How much ripple does the XY1205 have under load?

At 3.75 A, the measured output ripple was about 0.6 V.

How does the XY1205 differ from the XY1205A?

The reviewed XY1205 has CM-2 marking and a D-32 board, while the comparison unit has CM-1 marking and a D-26 board. The XY1205 lacks an input filter but has higher-capacitance output capacitors.


This model is included in the summary table: Comparison of power supplies: ripple, efficiency, and temperature rise

The figures from this review are in the measurement database: Power supplies

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister