/       /    Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.
Support the project on Patreon


Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.

$ 17.54
Go to store
I've described components for DIY chargers several times and shown how to use them.
This time, I decided to take a look at what a factory-made charger is like.
Of course, I've seen the insides of chargers before, but I initially liked this one simply for its looks. Let's take a look inside, too :)

I ordered and received it quite a while ago, but only just got around to it.

This charger comes in colorful packaging in the company's classic yellow and black colors.
The supported battery sizes and types are listed right away, and there are quite a few of them.
Lithium
16340
10440
14500
17500
17670
18350
18490
18650
22650
26650

Nickel-cadmium or nickel-metal hydride.
AA
AAA
AAAA
C

In other words, it supports any 3.7 V Li-ion, Ni-MH, and Ni-Cd batteries, as long as they fit. The maximum size is 26650.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.


What's included:
Charger
Power cable
Manual
Warranty card

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.


The power cable has the wrong plug, unfortunately, and no adapter is included.
But the cable itself is pretty good, about 1.1 m long.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

And here’s the charger itself.
The case is made of fairly sturdy plastic. Three yellow LEDs per channel indicate the charging progress.
The design is understated, which is exactly what I liked about it.
You can see the ventilation slots on the sides.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

The label on the back tells you pretty much everything: battery types and sizes, charging current, and input voltage.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

Before opening it up, I decided to test it first, just in case it didn’t work at all.
Nope, it started up and the LEDs began flashing.
The battery on the left is completely discharged; the one on the right is fully charged.
When charging is complete, the LED bar stays lit continuously. While charging, one LED on each channel flashes, but both channels charge in sync.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

And now I’ve finally made it inside. To do that, you need to pry out the four foam rubber feet and remove four self-tapping screws.
The negative contact is designed reasonably well: current flows through both the spring and the metal strip. At first I thought I’d improve it by adding a flexible wire, but after using it for a while, I realized that wasn’t really necessary—the contact never failed. I might modify it later, but for now I don’t see the point.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

The circuit board is held in place by one self-tapping screw (exactly the same kind used to fasten the case together).
The board even has a safety clearance between the high-voltage and low-voltage sections—something manufacturers often skimp on. The board itself also looks well made, although the assembly has a few flaws.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

I removed the last screw and took out the board. The metal strips and springs are soldered in place and come out with the board; the sliding contacts can be detached—they’re simply hooked onto the springs.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

A closer look at the top of the circuit board.
When I first planned to write this review, I intended to redraw the schematic from this circuit board. But the board has a very dark solder mask and lots of markings that obscure the traces. Of course, it’s possible to copy the schematic, but it would take quite a bit of work.
The power supply section is visible at the top of the board. There’s no mains filter, but there is a thermistor to limit the inrush current when charging the 10 µF input capacitor. The output capacitor is 1000 µF. I’d even say that’s overkill, since the charger’s power is no more than 5–6 W, even at maximum.
The output diode is also clearly over-specced. The power supply is controlled by a PWM controller with an integrated power transistor. Its marking has been carefully erased. Why? A mystery.
What could be so secret about a PWM controller, especially in a charger from such a well-known company?
Functionally, the charger consists of a power supply, two step-down channels, and a processor that controls the whole thing.
Approximate block diagram of the charger.

Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.

The processor’s marking has also been erased, though less carefully. You might think it was some kind of ATmega8, but no—the crystal is connected to different pins. And the crystal itself is a surprise: 24 MHz in a charger? What for? You could easily build something like this using the processor’s internal oscillator.
Overall, the engineers got as creative as they could.

Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.

The soldering is reasonably good, but the PWM controller in the power supply spoils the picture. It looks like everything else was soldered by machine, while the chip was soldered by hand. And the flux seems to have been washed off with something odd; there are white streaks on the board.

Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.

After examining the board, I moved on to testing.
My old camera uses four AA Ni-MH batteries. They’re getting on a bit—about 12 years old—but still work pretty well. They spent a long time discharged, but I managed to revive them.
I decided to test the charger with one of these batteries.
You can clearly see the 110 mA pre-charge current. The charger runs in this mode for about 15–20 seconds, then switches to the main charging mode at 500 mA. When the batteries are nearly charged, the current drops back to 100–110 mA. It should then automatically stop charging, but since I connected the battery in series with the meter, charge completion detection didn’t work correctly, and the charger kept running at 100 mA.
The last photo shows no current. That’s what the end-of-charge process looks like, but in this case the photo actually shows a pause in the charger’s operation.
I also noticed considerable heating while charging Ni-MH and Ni-Cd batteries. When charging lithium batteries, the device barely gets warm.
The charge termination voltage was about 1.47 V.
Warning: when I tried inserting a really bad Ni-MH battery, the charger decided it was a lithium battery and tried to charge it. It charged it to 2 V, and the battery heated up, so I stopped the process. When I tried another bad battery, the charger started flashing all the LEDs on that channel, then turned them off and refused to charge it.

Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty decent charger for Li-ion, Ni-MH, and Ni-Cd batteries.

Here I should explain a few principles behind how chargers work.
A charger usually supplies a constant current while measuring the voltage at the battery terminals. There are several ways to proceed.
1. The charger switches off as soon as it detects a voltage drop after a rise—this is called delta-voltage termination. It's used fairly often.
2. The charger holds the voltage at the battery terminals constant and waits for the charging current to drop below a set level, then stops charging.
3. Wait for a while, then stop charging.

This charger uses a slightly different charging algorithm, though it's a fairly well-known one.
I tried implementing this mode back when batteries like the 7D-0.115 were around.
The idea is to monitor the voltage at the battery terminals during pauses when no charging current is flowing. It looks roughly like this:
0.9 seconds — charging
0.1 seconds — voltage measurement.
Repeat.

What's notable about this mode is that it lets you charge different batteries without being tied to a particular charging current. If you monitor the voltage while charging, the battery's internal resistance affects the reading. Since the voltage here is measured during a pause, the internal resistance has practically no effect.

I hit a small snag while testing the lithium battery charging. It won't charge through the multimeter. The charging process “restarts” about once a minute.
Connected directly, everything works perfectly.
But while charging, the power supply makes a faint noise. It's not exactly loud, but you can hear it from half a meter away. The sound also varies depending on the charger's operating mode.
The charge termination voltage was 4.18–4.19 V

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

Here's what the battery charging graph looks like.
Test — battery type check (voltage detection) and polarity check.
Precharge at 100 mA
Main charge at 500 mA
Final top-up at 100 mA
Charging stops.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

I also tested it with an external 12 V power supply. It works fine, and the heating has almost disappeared.
I also measured the current drawn from the battery when the charger is unplugged: 1.8–2 mA. I wouldn't call that a lot, but it's not insignificant either.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

What I really liked was the reverse-polarity protection.
If you try to insert a battery the wrong way around, the charger flashes all three LEDs for that channel and refuses to charge it. Remove the battery and insert it correctly, and charging starts.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

Here's the new charger next to the one I used before, which I built about 10 years ago. It can charge only 4 batteries at a time and is based on Atmel's well-known application note AVR450. It could be used to build a charger for any battery type with your own specified characteristics. I compiled the firmware for four nickel-metal hydride cells.
It also has a power supply built around a TOP224Y.

Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.Nitecore i2, a pretty good charger for Li-ion, Ni-MH, and Ni-Cd batteries.

Summary.
Pros
Neat packaging (first impressions count)
Good build quality.
Supports a wide range of battery sizes and the main battery types.
Decent components and a good-quality parts selection.
Reverse-polarity protection.
Runs on both 220 V and 12 V

Cons
Unusual noises during operation
Gets hotter than expected when charging Ni-MH and Ni-Cd batteries.
Price.
Requires an adapter for our wall outlets.

My opinion. Setting aside the price of this charger and looking at it simply as a charging device, I really liked it. Functionally, it's a typical workhorse. I liked its ability to handle a wide range of batteries and its reverse-polarity protection. If you make or buy an adapter for a car cigarette lighter (though I have no idea where to get one), you can use it in a car.
The sliding contact is handled pretty well—not perfectly, of course (ideally, it should have an additional connection made with a flexible wire), but it's quite reliable.
I was surprised that the manufacturer had removed the markings from the ICs. I don't understand why a major manufacturer would do that.

The charger for this review was provided by the chinabuye store.
Would I buy this charger? In general, yes—but not at this price.

I hope this review helps someone make the right choice.
If you have any other questions, I'll be happy to answer them.
$ 17.54
Go to store
This page was found when searching for:
4-х канальное зарядное устройство для ni-mh  аккумуляторов схема , зарядные найткор схемы, https://www.kirich.blog/obzory/81-nitecore-i2-dovolno-neplohoe-zaryadnoe-ustroystvo-dlya-li-ion-ni-mh-i-ni-cd-akkumulyatorov, схема зарядного зарядное nitecore new i2, nitecore для li ion/ni mh/li po/ni cd схема, зарядное устройство ni cd аккумуляторов, схема зарядного устройства для nicd аккумуляторов, схема зарядного устройства для ni, зарядное устройство nitecore, найткор схема, зарядное для ni-cd аккумуляторов, аккумуляторы 12 вольт li ion, зарядка на атмега8 lkz li on, nitecore зарядка схема, nitecore i2

Questions and answers

Which batteries does the Nitecore i2 support?

It supports Li-ion, Ni-MH and Ni-Cd batteries. The review lists compatible sizes up to 26650 for Li-ion.

What is the Nitecore i2 charging current?

The specified current is 0.5 A per channel. Cutoff voltage is 4.2 V for Li-ion and 1.48 V for Ni-MH and Ni-Cd.

What drawbacks did the author find with the Nitecore i2?

The author reports operating noise, increased heat when charging Ni-MH and Ni-Cd, a high price, and the need for a plug adapter.

The figures from this review are in the measurement database: Chargers

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments5

Comments are published in their original language.

  1. 12 September 2019 16:31#1
    Моя Nitecore i2 оригинал, в одном слоте мигает 3 светодиода, второй слот работает как и раньше.
    Исправный слот видит и заряжает и Ni-MH и Li-ion аккумуляторы.

    Вскрытие показало:
    R16 маркировка R500 типоразмер 1206 имеет сопротивление 40 ом,
    поджаренные транзисторы в обеих каналах Q5 и Q7 маркировка X7YV.
    Q5 звониться накоротко.
    Так же потемневший текстолит в под этими элементами.
    Процессор 32 ноги, маркировка стёрта.

    Просьба помочь в опознании Q5 или по моей маркировке X7YV.
    0
    1. 19 September 2019 17:31#2
      Что-то великовато сопротивление, R500 это 0.5 Ома.
      Насчет Q5 не могу ничего сказать, я бы для начала попробовал определить что это на примере исправного транзистора со второго канала.
      После чего это все произошло?
      0
  2. 19 September 2019 18:06#3
    Спасибо за ответ.
    Пока ждал Ваш ответ, выяснил следующее.
    Если не ошибаюсь, то Q5 и Q7 может быть IRLML2244PBF – у них маркировка начинается на букву Х.
    Заменил Q5 на IRLML6402, зарядка заработала.
    Проверил дроссель из первого канала – транзистор-тестер показал, что это резистор с сопротивлением 0.40 ом.
    Снял термоусадку с дросселя – обмотка почернела.
    R16 и R36 действительно имеют номинал R500, 0.5 Ома. Тоже самое и на Ваших фото.
    Кстати разобрал копию Nitecore i2 – без наклейки – внутренности один в один с оригиналом.
    Выпал Q7 - исправный транзистор со второго канала.
    Транзистор-тестер показал что это р канальный полевой транзистор, так же показала и прозвонка мультиметром.
    Транзисторы Q5 и Q7, маркировка в оригинале X7YV, маркировка в копии X7HV.
    После чего это все произошло, никто не знает – просто сунув аккумулятор в первый слот увидел мигающие светодиоды.

    0
    1. 19 September 2019 20:26#4
      Вроде эти транзисторы с другой маркировкой это AO3407 (AO3407A).
      0
  3. 19 September 2019 22:01#5
    Спасибо. Может Вы и правы, но я посмотрел даташиты на AO3407 и AO3407A - про маркировку не нашёл.
    В сети пишут что AO3407 имеет маркировку A7. Но он в принципе похож же на IRLML2244PBF?  
    0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister