Illuminated push-button switches for 16 mm mounting holes
I ordered 4 buttons. The total came to 1.55+1.77+1.77+1.77=6.86. If I were ordering now, it would be considerably cheaper, since the ones I bought are all down to $1.29 each (5.16 total). The seller has lowered the price. Almost makes me want to order some more...
They were packed very simply: an envelope with a bag inside.

All four buttons were as ordered, and they also included four rubber rings.

I ordered black buttons: one momentary, and one with a plain round light.

The seller has a huge selection of options, divided into:
1. Black and chrome
2. Buttons that protrude and sit flush with the housing when pressed, and recessed buttons that are flush with the housing to begin with and press inward.
3. Momentary and latching
4. Different backlight colors
5. Different backlight voltages
6. Plain round backlighting or a power-button symbol

The buttons are marked with the backlight voltage, latching function, and backlight color. However, some of the symbols are swapped around, which can be confusing. As far as I can tell, Z indicates latching, while Y, G, and W indicate the color.
These are switching buttons, and the backlight contacts are independent, so there are 5 terminals in total.

In the seller’s photo, the backlight contacts are in the center. Mine are shifted slightly toward the edge, but the principle is the same: the three switch contacts are in the middle, and the two backlight contacts are on the sides.

The seller also shows four example wiring options:
1. The load and backlight turn on when pressed
2. The load turns on when pressed, while the backlight stays on all the time
3. The load and backlight turn off when pressed
4. The load turns off when pressed, while the backlight stays on all the time.
In principle, there are two more options: the backlight can turn on when pressing or releasing the button turns the load off—in other words, inverted operation.

1. Mounting diameter: about 15.8-15.9 mm, so the hole should be 16 mm.
2. Outer diameter: 17.8 mm
3. Overall length: 35 mm
4. Outer section: 1.5 mm

The seller also has a diagram with the dimensions.

There are buttons for hole diameters of 8, 12, 16, 19, 22, 25, 30, and 40 mm. But the 8 and 12 mm ones looked tiny, while 22 mm and larger seemed too big. I was choosing between 16 and 19 mm, and went with the 16 mm ones.
At least the 19 mm version can be ordered with different symbols, and there are so many that it’s hard to choose.

The purpose of the rubber ring is pretty obvious, but it’s so tiny that it only fits into the hole in the button itself. Just kidding :)

No complaints about the colors—white, orange, and green—or the evenness of the light.
The brightness does vary, though. Green was the brightest, white was a little dimmer, and orange (actually listed as yellow) was the dimmest. They’ll all be visible indoors, of course, but in bright light the white will blend in with the diffuser, and the yellow will be hard to see. So for those kinds of applications, I’d recommend green. I think red would also be noticeable.

The listing offered three backlight voltage options: 12, 24, and 220 V. Another listing also had a 3.3 V option; I think that’s just an LED without a resistor.
The current draw is very low: about 4 mA at 12 V and 1 mA at 5 V. The green one shines great at both 12 V (top) and 5 V (bottom). The orange (yellow) one is barely visible at 5 V, and the white one is so-so—you can see it, but it isn’t bright.

I also checked the contact resistance. The NC contacts are shown first in the photo, followed by the NO contacts. The only odd thing was the high resistance of the button's normally closed contacts: 0.3 Ω.

There is a subtle point when measuring the resistance of relay and switch contacts: for power contacts, you need to measure the voltage drop under load and then calculate the resistance.
Just out of curiosity, I tested them this way too. The voltage was limited to 1 V, the current was 1 A, and the multimeter was connected directly across the contacts.

I chose 1 A simply for convenience: a 1 mV drop is equivalent to a resistance of 1 mΩ.
The spread was quite wide, from 3.5 to 10 mΩ. The photos are in the same order as in the milliohm-meter test.

Resistance variation is pretty normal, but there are a couple of things to note:
1. If you simply apply power to the normally closed contacts, for example, the resistance is initially higher. After switching the button off and on under load, it drops as the current breaks through the oxide on the contacts. This is normal in most cases; just something to keep in mind.
2. When measuring the resistance of the normally closed contacts, pressing the button slightly makes the resistance go up. I think that if the button can't return all the way, for example because of dirt, the resistance will be even higher. This only applies to the normally closed contacts.

I like these buttons. They're not perfect, of course, but overall they're pretty good. They look great, have a changeover contact and even backlighting. I have just two complaints: the normally closed contacts and the weak yellow (orange) color.
As for the size: with my average-sized fingers, 16 mm is just about right. I'd have to press an 8 or 12 mm button with my pinky, so a 19 mm button might be more comfortable. Though I just tried them again—no, 16 mm is just right.
But for my purposes, none of these drawbacks matter. The only thing I'm unhappy about is that I paid more than I could have if I'd bought them now. I recommend them.
That's all. I hope you found this useful.
схема подключения кнопочного переключателя с алиэкспресс с подсветкой, e331298 zxh 2 datasheet, разбираем круглые переключатели с подсветкой
Questions and answers
What hole size do the illuminated push-button switches need?
They need a 16 mm hole; the mounting diameter is about 15.8–15.9 mm. The outer diameter is 17.8 mm and the total length is 35 mm.
How much current do the illuminated switches draw at 12 V and 5 V?
The author measured about 4 mA at 12 V and 1 mA at 5 V. At 5 V, the green light was bright, while the orange (listed by the seller as yellow) was very dim.
What drawbacks did the author find with these push-button switches?
The author noted dim orange illumination and quirks with the NC contacts: one non-latching button measured 0.3 ohms, and slightly pressing the button can increase NC contact resistance.
The figures from this review are in the measurement database: Other devices
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments2
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.