Vapcell F32 and F34 batteries: review and comparison
So today, it’s a “two-in-one” review, plus a comparison.
Let’s start with the lower-capacity ones, especially since I received them a little earlier.
Vapcell F32 18650 3200mah 10A/20A, $14.99 for a pair in the branded case — link.
The familiar case, and I have no complaints about its quality. But as I’ve mentioned several times before, it does add a little to the price.

Specs from the Vapcell website
Model: F32
Size: 18.4*65.0mm
Typical Capacity: 3200mAh (0.2C discharge)
Min capacity: 3100mAh (0.2C discharge)
Nominal voltage: 3.60V
Max Continuous Discharge Current: 10A
Max Discharge Current: 20A
End-of-charge voltage: 4.20V
End-of-discharge Voltage: 2.5V
Weight: 48g ( Appr)
Internal resistance: 28mΩ ( Appr) (AC 1kHz)
Standard Charge: 1000mA,CCCV 100mA cut-off
Quick Charge Current: 2500mA
The heat-shrink sleeve is blue, and the positive terminal is a flat four-point star. Otherwise, everything is pretty familiar.

The dimensions and weight are nothing surprising either.

They arrived at around 30% charge. Maybe they’d been sitting around for a long time, or maybe it was something else—I don’t know.
During the “conditioning” cycle, they delivered 3060-3080mAh at a discharge current of 500mA.

Two charging modes are supported: standard charging at 1A and fast charging at 2.5A.
Charging at 1A took 3 hours and 18 minutes. The CV phase is relatively short, which is good.

Charging at 2.5A took 1 hour and 40 minutes. In my opinion, this mode is a bit too demanding for these batteries, and I wouldn’t recommend charging them at more than 1.5-2A.

Vapcell’s specialists tested these batteries at three discharge currents: 2, 5, and 10A.

I’ll test them at more familiar rates: 0.2, 0.5, 1, and 2C, plus 10A.
The first cell delivered 3096mAh, or 11.33Wh, which is almost exactly the stated minimum of 3100mAh.

The temperature reached 54 degrees at 2C and 74 at 10A.

The second cell produced practically identical results, with the difference within the measurement error.

The temperature was the same story.

The comparison graph confirms how closely the results match, which is reassuring.

The batteries’ impedance as received, after “conditioning,” and at the end. Since they weren’t subjected to any extreme loads, though, I could have skipped the last measurement.

The second pair of Vapcell batteries is a new model. They only came out recently, and were even sent in a separate package along with the 21700 5000mAh cells.
Vapcell F34 18650 3400mah 10A/20A, $15.99 for a pair in the branded case — link.
When it comes to packaging, Vapcell sticks to what it knows: the same branded case.

Specs from the Vapcell page
Model: F34
Size: 18.4*65.0mm
Typical Capacity: 3400mAh (0.2C discharge)
Min capacity: 3300mAh (0.2C discharge)
Nominal voltage: 3.60V
Max Continuous Discharge Current: 10A
Max Discharge Current: 20A
End-of-charge voltage: 4.20V
End-of-discharge Voltage: 2.5V
Weight: 48g ( Appr)
Internal resistance: 24mΩ ( Appr) (AC 1kHz)
Standard Charge: 1000mA,CCCV 100mA cut-off
Quick Charge Current: 2000mA
The main visible difference from the previous cells is the color. For some reason, these ones are green.
The positive terminal is a flat five-point star, and all the necessary information is printed on the cell.

The dimensions and weight are nothing new either: standard 18650 size, though they’re a gram and a half heavier than the previous ones.

And, just like the previous ones, they arrived at around 25-30% charge.
In the first test, they came close to the rated capacity, delivering 3350-3380mAh. This test, however, was run at 1A.

Like the F32, these have two charging modes. But while the standard mode is also 1 A, the fast mode here is only 2 A, not 2.5.
In standard mode, charging takes 10 minutes longer: three and a half hours.

In fast mode, charging takes less than two hours.

Vapcell ran noticeably more tests here: 2, 5, 7, 10, 12 and 15 A, although the maximum continuous current specified for these batteries is 10 A.

I tested them in the same modes as the F32: 0.2, 0.5, 1, 2C and 10 A.
The results here match the specifications, falling within the 3300–3400 mAh range.
The first sample delivered 3344 mAh, or 12.08 Wh.

Temperature under 1C, 2C and 10 A loads. On average, it's about the same as with the F32, perhaps a little lower at 10 A.

The second battery delivered slightly less, 3325 mAh, but still meets the specification.

It heated up just like the first one.

The variation in parameters is slightly greater than with the F32, but still within an acceptable range.

And, of course, impedance measurements in the same modes as usual.

Now for some comparisons. I'll start with the F32 graph posted on Vapcell's website, where they compare it with a couple of LG models and one from Panasonic. The graph shows that, despite delivering roughly similar results, the F32 maintains a higher voltage during discharge.

Vapcell compared the F34 only with the Sanyo NCR18650GA, but in my opinion, they're almost identical here.

First, I'll compare the F32 and F34 with each other. The difference is noticeable, but only toward the end of the discharge.
Graphs at 0.2, 1C and 10 A.

I don't have all the batteries Vapcell used for comparison, but I can compare them with the Panasonic NCR18650BD and Sanyo NCR18650GA. Here are the results at 1C and 10 A.
Yes, the F32 and F34 maintain slightly higher voltage during discharge than their competitors, but they deliver less capacity overall.

Conclusion.
Overall, I liked these batteries, but for some reason the F32's capacity came in just barely above the stated minimum. It would make more sense to call them the F31, since their actual capacity is 3100 mAh.
I liked that all the batteries have consistent parameters and can handle the specified 10 A current without any trouble. I can't say anything about their longevity, but I can only assume Vapcell has once again used something proprietary.
That's about it. As always, comments and questions are welcome.
Questions and answers
What capacity did the Vapcell F32 and F34 deliver in testing?
The Vapcell F32 delivered 3096 mAh, while two F34 cells delivered 3344 and 3325 mAh. The F32 result was close to its 3100 mAh stated minimum; the F34 results fell within their stated 3300–3400 mAh range.
How hot did the Vapcell F32 get during discharge?
The F32 reached 54 °C at 2C and 74 °C during a 10 A discharge.
How did the Vapcell F32 compare with the F34?
The difference between them became more noticeable toward the end of discharge. Their discharge voltage was slightly higher than that of the Panasonic NCR18650BD and Sanyo NCR18650GA, but their total delivered capacity was lower.
This model is included in the summary table: Battery comparison: measured capacity and resistance
The figures from this review are in the measurement database: Batteries
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister



