/       /       /    A pair of JGNE18650 LiFePO4 batteries, 1600 and 1800 mAh
Support the project on Patreon


A pair of JGNE18650 LiFePO4 batteries, 1600 and 1800 mAh

1,75/1,95€ (без учета доставки)
Go to store
Not long ago, I was asked about reviews of LiFePO4 batteries. Then, not long ago, I received a package containing both 18650 and 26650 cells. They differ not only in size, but also in their specifications, capacity, and maximum current.
Since there are a lot of batteries, I decided to split them into three groups. Today, I’m reviewing the smallest ones.


The package was bulky, but the batteries actually took up only a small part of it. I’ll write separately about what else was in the package, but overall I can say that once again, the store gets a plus from me for the quality packaging.


Most of the batteries are marked with the manufacturer JGNE. I hadn’t heard of this company, which made testing them all the more interesting. Someone once asked me how the testing itself works, so here’s the answer: I often test all the batteries almost in parallel, using the appropriate battery testers. The main thing is not to get them mixed up. But the most interesting part starts when I put the review together. The photos, screenshots, thermal images, and result files are sorted into folders, and only when I’m preparing the final review do I see how the different batteries performed. During the tests, I usually don’t even keep track of that; I just collect the results. And I can tell you, it’s genuinely interesting to put everything together in graphs at the end, especially comparative graphs :)

So, I’ll start with the 18650 batteries. In this case, there are two models, with capacities of 1600 and 1800 mAh, and they were even packed together.


JGNE 18650 1600mah - 4.8A
The batteries are actually labeled Enerpower, but since the product page lists JGNE, that’s the name I’ll use in the review and on the graphs. Enerpower does have a website, with datasheets for most of the models I tested.

These cells cost €1.75 each, or €1.35 each when buying 40 to 99 units, which is not too expensive, really - link.


These batteries are neither high-capacity nor high-current, so I’d put them in the budget category.
Specifications from the store page:
Chemistry: LiFePO4
Type: 18650
UL: MH48108
Name: HTCFR18650-1600mAh-3.2V
Nominal voltage: 3.2 V
Maximum charging current: 1.5 A
Capacity: 1600 mAh
Continuous discharge current: 3C (approximately 4.8 A)
Internal resistance: <40 mΩ
Pulse load: 10 A / 5 seconds
Weight: 41 grams
Dimensions: diameter 18.2 mm / length 65.2 mm
Protection circuit: NO
Service life: 2000 full cycles (100% DOD) / 4000 full cycles (80% DOD) / 6000 full cycles (60% DOD)

Screenshot of the original datasheet.


The batteries look unremarkable: blue heat-shrink tubing and markings showing the voltage and capacity, but no manufacturing date.


Their dimensions and weight are within the stated specifications. I’ll note that LiFePO4 batteries are often a little lighter than “classic” Li-Ion batteries.


There was a small hiccup with charging. According to the datasheet, the charge termination voltage is 3.65 V, but I set it to 3.60.
In any case, the specified value is 3.65 +/-0.05, i.e. 3.6–3.7 V, which includes the value I used. Also, my experiments with LiFePO4 batteries have shown that because the charge curve is so steep at the end, any difference in capacity is extremely small.


After being discharged at 0.5C, the batteries were charged at the same 0.5C current to 3.60 V, with charging stopped when the current dropped to 0.1 A. In this mode, a full charge takes just under two hours.


As I’ve written many times before, I don’t believe batteries can be “broken in.” Still, to avoid unnecessary questions, I run an initial “dummy” cycle, which I consider a battery “normalization” step, so that all the batteries start under the same conditions.
This means a full charge, a full discharge, and another full charge. All the tests are run after that. The batteries arrived at about 80% charge.

For those interested, here’s the difference at 0.5C between the “conditioning” run (blue) and the main run (red).


And now for the tests.
According to the datasheet, the manufacturer specifies the battery capacity at currents of 0.1, 0.2, 0.5, 1, 2, and 3C.


I decided that wasn’t enough, so I also tested at 4C and 10 A. The datasheet says the latter load should be applied for no more than 5 seconds, but I discharged the batteries completely.
The results lead to two conclusions:
1. I didn’t get the stated 1600 mAh. I think we could squeeze out another 20–30 mAh by charging to 3.65 V and discharging to 2.0.
2. At a current of 4C (6.4 A), and especially at 10 A, there is a noticeable voltage sag, but what stands out more is the “hump” caused by the battery heating itself.


Temperature at 3C, 4C, and 10 A.
At 3C and 4C, things look quite decent, but at 10 A the battery has already heated up to 70 degrees. Although this temperature is not considered particularly high, the noticeable rise shows that the battery is under considerable strain.


The second battery performed almost identically.



I also ran a test to compare their characteristics, and you can see that the second battery has slightly more capacity.


The internal resistance results are not entirely clear-cut. It was about 32 mΩ at first, dropped to 30 mΩ after the first cycle, then almost returned to its original value after another 7 cycles. I could blame the instrument, of course, but I zero it before every test.



JGNE 18650 1800mAh - 5.4A
Almost an exact copy of the previous battery, but with slightly higher capacity and a higher maximum continuous current.
It costs a little more, €1.95. In this case, though, the wholesale price is not much lower than the retail price — product link.



Chemistry: LiFePo4
Type: 18650
Name: HTCFR18650-1800mAh-3.2V
Nominal voltage: 3.2 V
Maximum charging current: 1.8 A
Capacity: 1800 mAh
Internal resistance: <40 mΩ
Pulse load: 10 A / 5 seconds
Weight: 42 grams
Dimensions: diameter 18.20 mm / length 65.20 mm
Protection circuit: NO
Service life: 1500 full cycles (100% DOD) / 3000 full cycles (80% DOD) / 6000 full cycles (50% DOD)

These batteries are now sold under the JGNE brand, but I think they are still the same Enerpower cells, especially since the stated specifications match those in the datasheet.


The heat-shrink markings indicate that these batteries were made in mid-January 2020; the previous batteries had no production date listed. Otherwise, they look like the previous ones.


The batteries are so similar that I even took a comparison photo: the 1600 mAh model is on top, and the 1800 mAh model is below.


The dimensions are identical, and the weight is 2 grams higher, which also matches the description.


The charging parameters are also similar: the nominal current is 0.5C, or 900 mA.


At 0.5C, with a charge termination voltage of 3.6 V and cutoff when the current dropped to 0.1 A, charging took 2 hours. The battery was charged after being discharged at 0.5C.
And again, you can see that the CV phase is very short for batteries like these, which lets you charge them faster than “classic” Li-Ion batteries.


Results of the preliminary and main discharge measurements at 0.5C, effectively the initial and second cycles. There is a difference, but it is still small. These batteries were also charged to about 80% when they arrived.


The graphs here show discharge currents of 0.1, 0.2, 0.5, 1, 2, and 3C.


As with the previous model, the test included discharging at 4C and 10A, but there was no test at 0.1C either. I hadn't come across a requirement to discharge at that current before, so I didn't take that measurement.

The first battery delivered almost 1800mAh at 0.2C and 1767mAh at 0.5C, which is in line with the stated specifications.
I should note that the batteries performed noticeably better at 4C; the voltage sag was more pronounced with the previous ones.


The temperature rise at 3C, 4C, and 10A is very similar to that of the 1600mAh model.


The second sample performed slightly better, exceeding the stated 1800mAh capacity.


Temperature at 3C, 4C, and 10A.


The two batteries were more consistent with each other, although of course it's hard to judge based on just two samples, especially since the difference is within the measurement error.


The internal resistance of these batteries is lower, and it barely changed before testing, after the “break-in,” or after eight full cycles.


A little extra information.
First, a comparison graph for both batteries at 0.2C, 1C, 3C, and 10A.

The difference in capacity is clear from the labels alone, but the graph makes it easier to see how they perform at different load currents. The JGNE 18650 1800mAh clearly has not only higher capacity, but also performs better at high—and not just high—load currents. The difference is especially noticeable at 10A.


I often see comments saying that LiFePO4 batteries perform much better at sub-zero temperatures. That's partly true, but it doesn't apply to all models. For example, the models reviewed here are rated down to -20 degrees, but the manufacturer pleasantly surprised me by providing graphs for temperatures as low as -40, which is very rare.
The graph for the second case looks pretty grim, of course, but it clearly shows how much capacity the battery loses.

At -20, the 1600mAh model will have about 1100mAh, while the higher-capacity 1800mAh model will drop much further, by roughly a factor of three, to around 600mAh. So better performance at room temperature doesn't always mean it will remain the better option in other conditions.


But that's not all: the datasheets also include service-life figures, and here the 1600mAh model comes out ahead. The manufacturer specifies 4000 cycles at 1C before capacity drops to 80%; for the higher-capacity version, that figure is 3000 cycles.


There's also a high-current model, JGNE 18650 1100mah, with a maximum continuous current of 33A. That's extremely rare in the 18650 format, but unfortunately its capacity is low.

Conclusions.
These batteries offer neither high discharge current nor high capacity, but they're relatively inexpensive and retain some of the advantages of LiFePO4, such as safety and a long stated service life.
Although they look similar and you might think the only difference is capacity, that's not the case. The lower-capacity battery has a longer service life and performs better in the cold, while the higher-capacity one has better specifications but isn't worth using below freezing—in other words, it's a “room-temperature model.”
So there's no clear answer as to which one is better; their actual differences are too significant.

The batteries are temporarily out of stock at the moment; the website says they're expected to be back on June 12.
1,75/1,95€ (без учета доставки)
Go to store
This page was found when searching for:
lifepo4 18650 тест емкоси, jgne 18650-1800-3.2v 5.76wh, 4, аккумулятор 18650 1600, lifepo4 аккумуляторы 18650 тест, lifepo4 18650 1800mah тест, mh48108, jgne lithium battery manufacturers, разрядные характеристики литий ионных аккумуляторов емкостью 24v 200ah 400ah 600ah литий ионный аккумулятор для 12 квт, разрядные характеристики литий-ионных аккумуляторов емкостью 24v 200ah 400ah 600ah литий-ионный аккумулятор для 12 квт, аккумулятор 18650 характеристики, jgne, jgne 18650

Questions and answers

What capacity did the JGNE 18650 1600 mAh cell deliver?

The author did not obtain the rated 1600 mAh. Charging to 3.65 V and discharging to 2.0 V might have added about 20–30 mAh.

How does the JGNE 18650 perform during a 10 A discharge?

Voltage sag and heating were noticeable at 10 A; the cell reached 70 °C.

Which JGNE 18650 cell performs better in the cold?

The 1600 mAh model: at −20 °C its capacity is about 1100 mAh. The 1800 mAh model drops to roughly 600 mAh.


This model is included in the summary table: Battery comparison: measured capacity and resistance

The figures from this review are in the measurement database: Batteries

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister