/       /       /    Desk clock with a large VFD display and Wi-Fi time synchronization
Support the project on Patreon


Desk clock with a large VFD display and Wi-Fi time synchronization

$23.58
Go to store
My second clock from Taobao. Unlike the first one, this has a simpler display, but it's much larger—and that's what I like most about it, apart from the automatic time synchronization and its simply pleasant appearance.


First, a word about the price. As far as I can tell, shipping for this clock within China is free, which makes it a little cheaper to order :)

Some parts of this review will overlap with the previous one, since the same person developed both clocks. The control menu is very similar, and the settings are more or less the same.

The package contents are noticeably different this time. It includes:
1. Clock
2. USB-to-microUSB cable
3. IR remote control
4. Extra side panels
5. Hex key

I'm not entirely sure about the last item, since I ordered two clocks and the seller may well have included one key for both, which would be perfectly logical and understandable.


1. USB cable. A very ordinary cable, and unfortunately not as flexible as the one that came with the previous clock model.
2. Side panels for the case; more on those later.
3, 4. Remote control. For the most part, it just duplicates the three control buttons on the clock itself, but one mode can only be activated with the remote. The shape of the clock makes the remote more convenient to use, but clocks are usually something you set up and then forget about, so you can easily do without it.
A CR2025 battery is not included, so you'll have to buy one separately. A 2032 also fits (the kind used on motherboards), but it's a very tight fit.


The clock is quite large: 190x62x30 mm. Don't be alarmed—we'll get to its appearance in a moment :)


Out of the box, it's basically a block wrapped in paper. The only way to tell the top from the bottom is by the position of the light sensor.
On the back are a power cable opening, a buzzer, three buttons, and a temperature/humidity sensor, this time positioned well outside the case.


Before using it, you'll need to remove at least the paper from the front panel. At most, you can remove the protective paper from all the parts. It will work either way, but it looks better with all the paper removed.
Since I was going to take it apart anyway, I started with the screws on the back. If you're only removing the paper from the front panel, you don't need to take the back off. You can remove the paper carefully without unscrewing anything, but it's extremely awkward.


Once the back is removed, the top, bottom, and side panels simply lift out. When putting it back together, take care: the side panels can be installed in different orientations, but the cable opening will line up with the socket in only one of them.


The circuit board looks very neat. What's more, not only are all the components marked on the board, they're labeled too! That doesn't mean much to the average buyer, of course, but it does look tidy. The seller could easily offer them as kits for DIY assembly at a slightly lower price than the assembled version.

Speaking of thoughtful design, the clock has three microUSB power sockets—on the left, right, and back—so you can connect the cable wherever it's convenient, rather than having to make do with whatever works.


On the left are a holder for a 2025 or 2032 battery, one of the power sockets, three control buttons, a buzzer, and a photoresistor that serves as the light sensor for adjusting the display brightness.
As with the previous clock, the battery keeps the clock from resetting when power is disconnected. The settings are stored in nonvolatile memory, and if the developer adds automatic synchronization when power is restored, the battery will essentially be unnecessary.


The main electronics are in the middle of the board: a PT6315 display driver, a microcontroller, a DS3221 real-time clock, and an MP2307 regulator for the electronics.
The circuitry is clearly different. Since it uses a standard display without a built-in controller, a PT6315 driver has been added. The RTC chip has also been changed; this one uses the simpler DS3221. But since it has automatic synchronization, that doesn't matter much.
The 3.3 V MP2307 regulator presumably powers the microcontroller, the clock chip, and the WiFi module.


The WiFi module, the third USB socket, and an LT1617 converter that powers the display are installed on the right side.


There's an extra capacitor next to the WiFi module. It clearly wasn't part of the original design, but it's soldered on neatly, so we can let that slide.


The display. You could say it's large: it takes up almost the entire front panel. The characters are 27–28 mm high, and their total width is 122 mm. For comparison, the characters on the well-known Start kit clock are 21 mm tall.


To make the characters glow evenly, it has 10 filaments. If I’m not mistaken, the IVL1-7/5 had three.


On the left is the photodetector and the most delicate part of the display: the sealed-off tube through which the display was evacuated. Interestingly, these are usually at the bottom of flat displays, not on the side.


The seller’s page had a photo of this display next to a few others, and judging by the size, they were most likely an IV 11 or IV12.


The rarest and most unusual one, in my opinion, is the IV2. I couldn’t even find a photo of it lit up, only a drawing from its datasheet. This indicator was used in just two calculator models.


There are also some truly unusual, though more common, indicators from the IV9, 13, and 14 series, where the segments were formed using filaments (the ones at the top of the photo).



I got sidetracked there. We’re reviewing a clock, not different types of indicators :)

Here’s the complete clock kit. The extra case side panels are in the photo too. All that’s left is to peel off the protective film. Though for some reason, I left it on the bottom panel.


The display fits snugly against the front panel—not just with no gap, but with a little pressure. So don’t overtighten the screws.


When first powered on, the clock starts keeping time right away. If you remember the Start clock, it waited for you to press any button.


There was no need to peel the film off the back, but it does look better without it.


Now for the extra side panels. There are two types: standard ones for a flat setup, and additional ones for tilting the clock.


They simply replace the standard panels. Just make sure the holes line up with the USB ports; if installed incorrectly, the panel will be shifted either up or to the side. I also installed the battery while I was at it, since I’d forgotten about it at first.


This gives the clock a slight tilt, which I personally find more convenient. Maybe that’s because I’m used to the Start kit clock, which also had a tilted case.


The display is quite bright but not dazzling. It comes in just one color: green, or more precisely, lime green. The contrast is high, and with characters this large, readability is excellent. Even with my poor eyesight, I can see it perfectly.


Besides the time itself, status symbols appear on the left of the screen: a circle indicates before or after noon (although the clock uses a 22-hour format; more on that later), and arrows indicate that the alarms are enabled.


Current consumption is 510 mA at maximum brightness and 340 mA at minimum.


Settings. I have a feeling this is going to take a while, so let’s go through them in order.
1. Time synchronization and Wi-Fi connection setup. It’s the same as on the previous clock, except that this mode displays 88888 on the screen. A reminder: the Wi-Fi password is 88888888.
2. Enable alarms. 0 = off, 1 = first alarm on, 2 = both alarms on.
3, 4. Set the times for the first and second alarms; additional symbols appear on the screen accordingly.
5. Enable NTP synchronization. n = on, F = off.
6. Synchronization sets the date as well as the time, which is needed at least for the daylight saving time change. You can also set it manually: year.
7, 8. Month and day.
9. Set the hours and minutes (two steps).
10. Set the seconds, though resetting them to zero would have made more sense.
11, 12. Manual and automatic display brightness.
13, 14. Adjust brightness in manual mode, with 8 levels. You can also switch between these modes at any time using the Enter button on the remote.
15. In manual brightness mode, pressing Enter on the remote displays the brightness reading from the ADC, though I still haven’t figured out why.
16. Screen information display mode; more on that later.
17. Time zone.
18. Daylight saving time. For some reason, enabling it also turns on the before/after-noon symbol.


Synchronization is fast; even when far from the router, it takes just 10–15 seconds. Here's a real-time demonstration: I deliberately set the time to something random, then started synchronization using the remote.


Information display modes. There are actually four, but modes 1 and 3/4 appear to be identical, or I couldn't figure out the difference, so I'll show two.
1, 2. Mode 0 or 1: just the clock, nothing extra :)
3–6. Mode 2 or 3: cycles through Clock, Date + day of the week, and Humidity + temperature.

By the way, about the temperature: since the sensor is outside the case, the temperature reading here is accurate, probably within ±0.5 degrees. It also seems that the humidity sensor works more accurately, since its readings can be affected by temperature too. As a result, it shows slightly higher humidity than the previous clock.


Modes 3 and 4 in action


Overall view. The light sensor is a bit of an eyesore, as it's noticeable against the almost-black case.


I'd like to compare the two clocks, but they're actually so different that it's hard to compare them. One has smaller characters but a more complex display, interchangeable filters, a metal case, and a more flexible cable. The other has a larger display, several connectors for easier hookup, and a remote. The only thing they really have in common is that they both tell the time and support synchronization.


And how could I not take a comparison photo next to the Start kit clock I've mentioned several times? It's obvious that the Start clock is noticeably dimmer. That said, using the flash played a part, and the new clock was set to maximum brightness.


I turned on auto-brightness on the new clock. It helped a little, but my old one actually shines brighter than it looks in the photo. On the other hand, it's already 30 years old, so what can you expect...



All in all, I liked the larger clock better, perhaps because of my poor eyesight, or perhaps because I'm used to our Start clock. My wife said she prefers the one with the metal case, mainly because of its appearance. So it's not that clear-cut.
I also like that the characters are slanted here, unlike on the previous clock's display, where they're perfectly vertical.

A few ideas for improvements:
1. I'd recess the side connectors further into the case so they don't stick out so far.
2. Add a mode that alternates only between the time and temperature + humidity. The date isn't always needed and can sometimes get in the way.
3. Display the date as day/month rather than month/day; that's what we're used to.
4. Automatic synchronization on startup. The developer said they're going to add this.
5. I'd make the hours/minutes separator blink at 1 Hz instead of 0.5 Hz, as is usually done. Right now it stays lit for a second, then turns off for a second, which feels odd. I think it would be better to have it on for 0.5 seconds and off for 0.5 seconds.
6. Maybe have two brightness levels based on the time of day rather than the sensor.


I think that's about it. As always, thanks for reading. If you have any ideas for improvements, let me know.
$23.58
Go to store
This page was found when searching for:
настольные часы с синхронизацией времени по wifi своими руками, wifi desktop clock with digital led display support wifi auto-calibration, https://www.kirich.blog/obzory/obzory-bytovoy-elektroniki/727-nastolnye-chasy-s-bolshim-vfd-displeem-i-sinhronizaciey-vremeni-po-wifi, применение ds3221, wi-fi часы с синхронизация времени с алиэкспресс, часы реального времени с ручной коррекцией времени своими руками, часы с корректировкой времени, часы с корректировкой по интернету, часы с корректировкой времени wifi, часы настольные с wifi синхронизацией, есть ли настольные часы с синхронизацией, ив-11, настольные электронные часы с синхронизацией времени, корпус для часов wi-fi, настольные электронные часы с автосинхронизацией времени по wifi, часы на дисплее vfd от кассы, часы excelvan с радиосинхронизацией времени, комнатные электронные часы с синхронизацией по wifi, часы vfd срок службы, часы настольные с коррекцией времени, часы будильник wifi синхронизация времени, часы с радиосинхронизацией настольные, часы комнатные с синхронизацией времени, vfd clock, цифровые часы настольные с синхронизацией времени по wi fi, часы с wifi, часы с дисплеем, настольные часы, часы с wi-fi, настольные часы с дисплеем, настольные часы с wifi, тест часов, обзор часов

Questions and answers

What are the dimensions of this desktop VFD clock?

The clock measures 190×62×30 mm. Its characters are 27–28 mm high, and their total width is 122 mm.

How does the clock synchronize time, and what does it display?

It supports Wi-Fi time synchronization and has a temperature/humidity sensor. The author says the developer still needs to add automatic synchronization when power is restored.

What improvements did the author suggest for the clock?

He would recess the side connectors further into the case, add a mode that alternates between time and temperature/humidity, and show the date as day/month. He also finds the separator’s one-second blinking interval unusual.


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments1

Comments are published in their original language.

  1. 4 April 2019 01:54#1
    Спасибо за обзор очень интересные часики.
    +1

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister