3-Watt 2820 LED Arrays
$0.84
As I said, one of the lights installed more than four years ago failed. The cause isn't clear: it may have been a coincidence, or it may really have overheated, since the light was about 1.8 m above a gas stove. The other three lights are still working fine.
In any case, I had to find a way to get it working again, or look for an identical replacement for sale, which would be more expensive and harder to find.
My first attempt was to replace the driver; I'll talk about that later. For now, I'll describe what actually worked to repair it.
The failure was caused by a faulty LED module. A search on AliExpress led me to a store with a huge selection of these modules. I was surprised by the variety of shapes, power ratings, and sizes. Below are photos of just some of the options from one store.
Link to the page for the first photo
Link to the page for the second photo.

I ordered six LEDs. At the time, they cost $0.77 each; the seller has raised the price a little since then, but I think that's temporary.
The packaging was a standard sealed antistatic bag inside an ordinary yellow envelope. I'd give the packaging a C: the LEDs could have damaged each other, and they were sticky, too.

Just in case, I ordered LEDs in two color temperatures: four warm white and a couple of what they call “natural” white. The original lights had warm-white LEDs.
The difference isn't visible in a regular photo, so I had to improvise a little to make it show up. The warm ones look more yellow.

A closer photo. Here and below, warm white (3000 K) is on the left, and natural white (4200 K) is on the right.
You can just make out six small phosphor-coated LEDs inside, as far as I understand the construction of COB modules. The power rating is 3 W, but modules of exactly the same size are also available in 5, 7, 10, and 12 W versions.

The LEDs are size 2820, meaning a 28 mm board diameter and a 20 mm diameter for the COB LED assembly itself.

The modules are exactly the same size. In this photo, one is sitting on top of the other, but the metal base has been cut rather roughly in places.

Since we're talking about different modules, here's some reference information on the sizes of other modules.

I was also interested in some of the very powerful, large options, especially the second one, with a diameter of 160 mm and a power rating of 200 W. It costs about $23, though. On the other hand, if needed, Chinese manufacturers can churn out even 500 W versions. The main thing is finding a base, because assembling these modules is extremely simple: make a board, solder the LEDs to it, glue it to a metal base, and cover it with phosphor or a special compound.

Since LED modules get noticeably hot in operation, I mounted them on a temporary heatsink for testing. It's obviously too small for continuous operation, but it's fine for relatively short tests.

LEDs are driven by current, not voltage, so I set the power supply's current limit to 300 mA and gradually raised the output voltage as an experiment until the power supply switched to constant-current mode. The LEDs are connected in series, so the voltage across each one and the total power need to be divided by two.
1. The LEDs start to glow at 14 V, with the current below 1 mA, too low for the power supply to register.
2. At 15 V, the brightness increases noticeably, but the current is still less than or around 1 mA.
3. At 16 V, they are already glowing quite brightly. The current is 19 mA, and the power is about 0.3 W for both LEDs.
4, 5. The voltages are 17 and 18 V, respectively; the currents are 72 and 161 mA, and the total power is 1.2 and 2.9 W.
6. Normal operating mode: 300 mA, almost 19 V across the two modules, and 5.64 W for both, or 2.82 W each.

I ran them like this for quite a while, but the temperature peaked at just 64 degrees, so I think everything was fine and safe in that respect.

It turned out that the voltage across the modules was different: it was a little lower on the “warm” one than on the “natural” one. As it warms up, the voltage drops slightly. That's normal. In my case, the "natural white" one ran a little hotter because it was also dissipating slightly more power: 2.9 W versus 2.76.

It also turned out that they not only draw different amounts of power, but shine differently too. The "natural white" one (on the right) has less of a "spotlight" effect, meaning its light is more diffuse.

Without the light filter, you can already see the difference in color temperature.

It feels like the modules use completely different LEDs. I noticed that during the visual inspection, though it's hard to make out in the photo. The LEDs in the "natural white" one on the right are slightly smaller and probably have a little less power, which is why the voltage across them turned out higher than on the "warm white" one.

Photo with the flash forced on.

And here's the "culprit." When I bought it, I chose one with a heatsink, and four years later I can say that was the right call.

I'm looking for similar lights again now, but with frosted glass, since I mentioned back then that I didn't like the bright spots caused by the reflector design. At first I wanted to choose one in a local store; the price was about the same as in China, but the ones I saw there looked roughly like the examples below. Don't pay attention to the power rating: even 3–5 W in this kind of design won't last long. Now I'm looking for lights with proper heatsinks, but for some reason I keep finding models with three to five high-power LEDs rather than COB arrays.

Since the lights aren't at my place, when I heard that one had failed, I first assumed the driver had burned out; I didn't suspect the LED. In the end, I ordered four new drivers.

The original one is on the right, the ones I bought are on the left. They cost next to nothing, about 70 cents, and are rated for up to 3 W — link.
The old one uses a BP9011, which I hadn't come across before. The new one uses the popular BP9021A, and it's indeed rated for 3 W.

Driver schematic. Current regulation is on the primary side, which is perfectly normal; that's how practically all low-power drivers are designed.

I didn't take the light apart for the review because, quite simply, I couldn't figure out how to open it. Or perhaps the one I tried was screwed on very tightly. It turns out it's very easy to take apart: the top section unscrews, and the light separates into several pieces. For some reason there's a thread between the reflector and the front section, even though it only gets in the way, since the reflector has pins to stop it from turning. But the thread is so shallow that it doesn't cause much trouble.

This model has a heatsink at the back, and the entire body is made of aluminum, albeit relatively thin.

Since there are no screws holding the array in place, it's probably glued on.

That's exactly how it turned out: the array was glued on so firmly that I bent the aluminum substrate in places while removing it. I finally got it off by pushing it up from below through the wire hole.

There were even traces of the paint from the housing left on the substrate.
The arrays look very similar, but they are still different. In my case, that wasn't critical. Before ordering, I first measured it and tried searching by the dimensions, but then noticed it was also marked 2820. Interestingly, the array itself was slightly offset on the substrate (the module on the right in the photo).

The reflector presses the array against the housing, so I could simply have applied thermal paste and clamped the whole assembly in place, but I wasn't happy with that solution. Inside, I could see five holes: three threaded ones, clearly for three-LED modules on a "star" substrate, and a pair of smaller holes, about 1.5 mm in diameter, exactly where they needed to be to mount a module like the one I'm reviewing. The rest was straightforward: a drill bit, a cordless drill, a couple of taps, and the holes were ready. Drilling was very easy; I didn't expect that and nearly drilled into the table.

I cleaned some of the glue residue out of the inside. Ideally, I should have removed the paint too, but I decided it would be fine as is since the power is low.

Now for the thermal paste, a couple of screws, and a couple of washers. I needed the washers because I’d initially chosen screws with large heads and was worried they might short against the neighboring contact pads.

This part took some fiddling: I had to pack the wires in so they wouldn’t short against the metal backing plate.

I ended up replacing the screws with regular ones with small heads, so the washers were no longer needed. Heat is dissipated through roughly 1/4–1/3 of the backing plate, since there’s a gap underneath for the wires.

I also had to file down the reflector a little because the screws were in the way. I’d suspected this from the start, though, so it wasn’t news to me.
I also cut off the plastic pins, which I think was a mistake. During assembly, the reflector kept trying to rotate, and the pins were supposed to stop it.

Almost done; all that’s left is to sort out the driver.

At the very beginning of the repair, I temporarily connected the new driver and decided to compare one of the new ones with the old one.
It turned out the current was almost identical, with the old one (on the right) being slightly lower. I ended up keeping it, since four identical new drivers are better than three new ones and one old one—might come in handy later.

This was just an experiment: with the light on and connected through a multimeter, I switched on the display for maximum and minimum peak current. A few seconds later, the meter showed how much the current varied. The maximum peak was almost 500 mA, and the minimum was just under 100 mA.

Now it’s really all done: the wires are soldered to the driver, and the driver itself is installed in the housing. I made the ventilation holes back when I installed the lights.

I was about to wrap things up on this positive note and happily confirm receipt of the order, giving the seller five stars. But something made me check the other four modules first—and it turned out to be a good thing I did.
Two of the six modules in total—or two of the four in this color—had a problem: one LED on each wasn’t working. One went out after a few seconds at its rated current, while the other hadn’t worked from the start.


I ran into a similar issue around the time I was writing my review of the lights: I bought 10 W LEDs, and they were all defective. The seller issued a full refund without any questions. I did end up using the modules anyway, but only for a secondary purpose.
I wrote to the seller right away, saying that I’d received and connected them, and two out of six weren’t working properly. The seller replied with a question: “What voltage are you powering them with?” I thought, aha, trying to catch me out :)
I replied, “No, my friend, LEDs are powered by current, not voltage. The current is 300 mA, and the voltage across the module is about 9.3 V.”
About 15 minutes later, the seller asked if they could send me two replacement modules. I thought, why not—send them over. I’d wanted to buy four, not two, and they’re dirt cheap anyway.
All in all, I can say that buying LEDs with a 50% chance of defects isn’t very appealing. Even if the odds are 33% (of the total), that’s still not great. The only thing that saves the seller here is that they agreed to send replacements without much fuss, but I’m not sure I’ll buy from them again.
That’s all from me. I hope this review was useful and will come in handy for anyone planning to buy LED arrays from China.
$0.84
This page was found when searching for:
цоколевка светодиодов 3 ват, как крепятся светодиоды 3 вт, схема светодиодный модуль в морозильном ларе, 3, крепление 3 ватных светодиодов, светодиод 3 ватта устройство, светодиоды 12 вольт 3 вт на плашке монтажной пластине, светодиодные сборки для фонариков 3.6 вольт, светодиодная сборка 3 светодиода bs-4634в, светодиодные сборки купить, https://www.kirich.blog/obzory/osveschenie/640-svetodiodnye-sborki-moschnostyu-3-vatta-tiporazmera-2820, pushlight 3 вт разобрать, br9021a, yd28-16, светодиод круглый 20мм 0505 2820, светодиодная сборка hx l5103, светодиоды 3 вт для светильника, точечный светильник modular 108820xx3w характеристики и вольтаж, 2b6c светодиодная сборка ампер, фонарь универсальный эра p3w, 3 вт led,схема, сборка лампы из 3ватных светодиодов, светодиодная модуль 24 вольта 3 вата круглый, адресный пиксельный dc контроллер светодиода на 3 ватта в задний с топовый фонарь, светодиоды для подложки 3w, как запитать 2820 диодную сборку, светодиоды 3 Ватта, светодиодные сборки, светодиоды для светодиодных светильников, технический обзор светодиодов
цоколевка светодиодов 3 ват, как крепятся светодиоды 3 вт, схема светодиодный модуль в морозильном ларе, 3, крепление 3 ватных светодиодов, светодиод 3 ватта устройство, светодиоды 12 вольт 3 вт на плашке монтажной пластине, светодиодные сборки для фонариков 3.6 вольт, светодиодная сборка 3 светодиода bs-4634в, светодиодные сборки купить, https://www.kirich.blog/obzory/osveschenie/640-svetodiodnye-sborki-moschnostyu-3-vatta-tiporazmera-2820, pushlight 3 вт разобрать, br9021a, yd28-16, светодиод круглый 20мм 0505 2820, светодиодная сборка hx l5103, светодиоды 3 вт для светильника, точечный светильник modular 108820xx3w характеристики и вольтаж, 2b6c светодиодная сборка ампер, фонарь универсальный эра p3w, 3 вт led,схема, сборка лампы из 3ватных светодиодов, светодиодная модуль 24 вольта 3 вата круглый, адресный пиксельный dc контроллер светодиода на 3 ватта в задний с топовый фонарь, светодиоды для подложки 3w, как запитать 2820 диодную сборку, светодиоды 3 Ватта, светодиодные сборки, светодиоды для светодиодных светильников, технический обзор светодиодов
Questions and answers
What are the specifications of the 3 W size-2820 LED modules?
The board is 28 mm in diameter, and the COB assembly is 20 mm. At 300 mA, the author measured almost 19 V across two modules in series and about 2.82 W per module.
How hot did the size-2820 COB modules get during testing?
On a temporary heatsink, their temperature reached a maximum of 64 °C. The author considered this acceptable for relatively short operation.
How many of the purchased size-2820 modules were faulty?
Two of the six had a non-working LED. The seller agreed to send two replacement modules.
The figures from this review are in the measurement database: Other devices
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments4
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister



Comments are published in their original language.