/       /       /    Interesting 0–21 mm micrometer
Support the project on Patreon


Interesting 0–21 mm micrometer

Today I’m reviewing a rather unusual measuring tool. I saw it at a friend’s place and couldn’t resist showing it to you. I hope you find it interesting.

As usual, a reminder: to keep up with new posts on the blog, I recommend following me on Instagram, where I’ll post notifications about every new topic and might also write about something interesting now and then — link to the account

I don’t think many readers are unfamiliar with measuring tools like rulers, calipers, and micrometers, but this particular instrument is genuinely unusual.

First of all, it clearly wasn’t made in an industrial setting—not by a specialized company that manufactures measuring instruments, anyway. I’d guess it was made in a machine shop at some factory.

At first, it didn’t look very good. The photos show it after cleaning and lubrication.


But that’s not all. What caught my eye at first was the size of this micrometer. It’s really compact, not much bigger than a matchbox.


For anyone who doesn’t know the names of the parts of a micrometer, here’s a picture of its bigger “brother.”


The design is extremely simple: a steel frame, anvil, and screw measuring mechanism.


The measuring range is 0.01 to 21.00 mm, with a scale division of 0.01 mm. There’s no ratchet to limit the measuring force. Also, it actually reads -0.01–0.02 mm at zero. When taking measurements, I relied on feel and tried to apply roughly the same pressure as a ratchet would.


You can adjust the zero position if you want using the adjustment screw, which is actually part of the anvil.


Interestingly, the numbers on the scale aren’t just slapped on there—they’re quite nicely and relatively intricately made. I can’t say how they were produced: engraving or chemical etching, probably the former. Judging by the font, this micrometer was made a long time ago.


Unfortunately, when I was preparing this article, I didn’t have any gauge blocks or feeler gauges on hand, so I had to make do with what my friend had: drill bits of various diameters.


Diameters: 1.0, 1.5, 2.0, 2.5, 3.0, and 3.5 mm. Each measurement was slightly high by 0.02–0.04 mm. Taking the initial 0.02 mm error into account, that gives a deviation of 0–0.02 mm, which seems fine to me.


Diameters: 3.5, 4.0, 4.2, 4.5, 6.0, and 6.5 mm.
The 3.5 mm bit measured the same as the previous ones, but everything larger read 0.05–0.06 mm high. In this case, though, I’m inclined to think the drill bit shanks really are that much larger, rather than the micrometer’s error increasing—but that’s just a guess.


What can I say? It’s hard to draw conclusions about accuracy without precision standards, but subjectively, it seems quite good.

What I liked most was how compact it is. When I first saw it, I was genuinely delighted—it’s like a little toy. Very cool :)
Special thanks to my friend for this fascinating instrument and for helping me prepare the review.

Questions and answers

What is the measuring range of the 0-21mm micrometer?

Its range is 0.01–21.00 mm, with 0.01 mm scale divisions.

How accurately does the 0-21mm micrometer measure drill bits?

For 1.0–3.5 mm bits, readings were 0.02–0.04 mm above nominal. Bits from 4.0 mm read 0.05–0.06 mm high; the author suggests their shanks may actually be larger than their stated diameters.

What are the drawbacks of the 0-21mm micrometer?

It has no ratchet to limit measuring force, and its zero initially reads about −0.01–0.02 mm. The zero can be adjusted with a screw.


This model is included in the summary table: Comparison of measuring instruments reviewed on the blog

The figures from this review are in the measurement database: Measuring instruments


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments2

Comments are published in their original language.

  1. 7 July 2022 22:50#1
    Реально удивительно уникальная вещь. Браво мастеру, изготовившему когда то микрометр, особенно поражает нанесенная оцифровка и деления! Наверное, был инструментальщик высочайшей категории!!

    Браво kirich'у за прекрасный обзор!

    ... вот все что больше, показали на 0.05-0.06мм больше, но в данном случае я склонен считать, что это реально отличие диаметра хвостовика сверл, а не увеличение погрешности микрометра, но это лишь предположение.

    Скорее всего, так и есть. Меня, когда-то, инструментальщики учили мерять диаметр свёрл по режущим кромкам.
    --------------------
    Не шалю, никого не трогаю, починяю примус ....
    +3
    1. 9 July 2022 00:34#2
      Да, вещица просто обалденная, правда в обзоре я немного ошибся, микрометр показал диаметр хвостовика меньше заявленного, но не суть, на мой взгляд все равно классно, жаль прибора для перепроверки нет.
      +2

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister