Review of the AUKEY PA-T15 charging station with 5 USB ports and Quick Charge 3.0 support, plus a brief comparison with the AUKEY PA-T1 Quick Charge 2.0
$21.72
My selection criteria were simple:
- several USB ports (at least 3);
- 1–2 of the ports should support Quick Charge;
- a power cord for plugging into the wall. It's more convenient and reliable than a charger that plugs directly into the outlet.
- a well-known manufacturer;
- good looks.
Let's take a look at what fast charging is and which standards are available.
Modern smartphone batteries have much greater capacity than those in feature phones, but they also run down noticeably faster. Sometimes you need to top up the battery in a short time—for example, while taking a morning shower, so you can post a couple of photos on your way to work or read a review of a new gadget. Smartphone manufacturers use fast-charging technologies for this, some of which can provide several hours of use after just 5–10 minutes of charging.
In 2014, California researchers published a study in Nature Materials that challenges the prevailing view that fast charging shortens battery life. According to the researchers, charging evenly—whether quickly or slowly—prevents localized heating that can reduce battery lifespan.
Since there is no single fast-charging standard, some manufacturers use their own proprietary standard, while others support the more common Qualcomm Quick Charge or MediaTek Pump Express. All fast-charging standards use the same basic approaches: they increase the charging current, raise the voltage, or do both at once.
My Samsung Galaxy S7 supports Quick Charge 2.0 (up to 15 W at 9 V), as well as Samsung's proprietary Adaptive Fast Charge (up to 15 W at 9 V). The Samsung EP-PN920 wireless charger also supports both fast-charging standards. In the smartphone settings, you can choose whether to enable fast charging or charge it the regular way. Not all phones with fast charging offer this option.

The USB 2.0 specification supports powering devices at up to 2.5 W (5 V, 500 mA), so if the battery's charge controller can't tell which port it's connected to, it will limit its power draw. The controller and charger communicate over the Data pins (D+ and D−). In most cases, simply shorting these pins is enough for the charge controller to draw more current. Some devices require a specific circuit on the Data pins; they use the voltage on those pins to determine the charger's voltage and maximum current rating.
The Qualcomm Quick Charge 2.0 specification appeared in 2015 and allows the charging voltage to be raised to 9, 12, or 20 V, but only after the charger and device negotiate. First, the charge controller checks the state of the D+/D− lines to determine whether it's connected to a compatible charger. It then applies a specific voltage to the D+/D− lines to request the desired supply voltage.
Description of the negotiation process and photo from Wikipedia.
When power is first applied (state S1 in the diagram), the charger supplies 5 V to the load and shorts the D+/D− lines. The charger is then recognized as compliant with the USB Battery Charging specification. To switch to Quick Charge 2.0 mode, the device applies 0.6 V to D+ (state S2). The charger recognizes this voltage as a QC 2.0 request from the device and responds by disconnecting D+ and D− and shorting D− to 0 V. The device now also recognizes the charger as QC 2.0-compliant and applies 3.3 V to D+ (state S3). The charger then releases D− and reads the voltage combination on D+/D−, which the device uses to select the required supply voltage. State S3 shows a 9 V output, state S4 a 12 V output, and the next state a 5 V output.

Qualcomm Quick Charge 3.0 appeared on the market in 2016, is backward-compatible with previous versions, and introduced INOV (Intelligent Negotiation for Optimum Voltage). This algorithm lets a device dynamically calculate the power level it needs at any given moment and smoothly adjust the rate of energy transfer. The charging voltage is adjusted in 200 mV increments, from 3.2 V to 20 V. This optimization reduces wasted energy that would otherwise be dissipated as heat, makes charging more efficient, and prevents the battery from overheating, extending its service life.
Another quote from Wikipedia.
In 2015, the USB-IF published a test procedure for cable infrastructure with Type-C connectors, explicitly prohibiting non-standard methods of controlling the voltage on the power line. As a result, Quick Charge 2.0 and 3.0 chargers with a USB Type-C connector can no longer receive certification. Google issued a recommendation that Android devices not support QC 2.0 or 3.0. To address this problem, Qualcomm promised to release a new revision of the Quick Charge 4 specification in 2017.
Quick Charge 4 was introduced back in 2016, and Quick Charge 4+ followed in the summer of 2017, but there are still few devices that support these standards.
Several manufacturers make devices that meet the criteria I mentioned. But the brands most respected on the forums are Aukey, ORICO, CRDC, Floveme, and Tronsmart. Their devices are very similar, and some may even be made in the same factory. I went with Aukey. I liked that the company specializes in chargers, has its own English-language website and social media pages, and that Aukey chargers are listed in the list of supported devices on Qualcomm's website.
Only the PA-T15 and PA-T1 were available with shipping from Russia in Aukey's official AliExpress store, so those are the ones I ordered. I chose the PA-T15 for myself, even though I don't have a single device that supports QC3.0. I didn't want to buy identical chargers; it's always more interesting to compare them.
The store shipped my order the next day, and it was delivered by IML. I received a message from them on Viber saying that the order was out for delivery. The courier brought it to me the following day. Five days passed from the time I placed the order.
Here are links to the chargers:
1) AUKEY PA-T15 with Quick Charge 3.0 support, available from the official Aukey store on AliExpress.
2) AUKEY PA-T1 with Quick Charge 2.0 support, available from the same store
Aukey PA-T15 specifications
Technology: Quick Charge 3.0 & AiPower
Input: AC 100-240V
Output 1-4 (AiPower): 5V 7.2A Max
Output 5 (Quick Charge 3.0): 3.6V-6.5V 3A | 6.5V-9V 2A | 9V-12V 1.5A
Weight: 149.1g / 5.26oz
Power:54W
Size (L*W*H):94*60*25 mm
Certification quality:FCC,CE,RoHS
Aukey PA-T1 specifications
Technology: Quick Charge 2.0 & AiPower
Input: AC 100-240V
Output 1-4 (AiPower): 5V 7.2A Max
Output 5 (Quick Charge 2.0): 5V 2A | 9V 1.67A | 12V 1.25A
Weight: 680g / 24oz (clearly a mistake here)
Certification:CE, RoHS, CB, PSE, TUV, UL,FCC
Both Aukey chargers have one USB port that supports Quick Charge (orange); the other four USB ports support AiPower (green).
Aukey's AIPower technology automatically detects the connected device and adjusts the USB port's output to suit it, providing up to 2.4A per port at 5V. AiPower works effectively with Android and iOS phones, as well as other devices.
Unboxing, appearance, and dimensions.
The parcel arrived in a plastic bag, with a soft foam lining inside. Each box was in its own bag. The packaging was excellent.


The chargers are packed in branded cardboard boxes, sealed in plastic wrap.


Inside are the charger itself, a power cord, a micro-USB cable, a clip, a warranty card, and a manual.


The PA-T15 box didn't include a warranty card. Otherwise, the contents are the same.


The chargers have identical cases. The top and bottom surfaces are matte, while the sides are glossy. The case is printed with the basic information—brand, model, key specifications, and certifications—and the USB ports are labeled.

The USB ports are on one of the short ends, and the power cord connector is on the other. The long sides are blank.
The photo clearly shows how easily the glossy finish picks up every bit of dust and debris from the table.

The chargers are quite compact. Looking at the photos on AliExpress, I expected them to be bigger. But they do match the stated dimensions.



I was surprised by how short the power cord is—just 75 cm. If you put the charger on a desk, the cord barely reaches the floor. If the outlet is even a little farther away, the cord won't be long enough.

There is no indicator on the case to show that the charger is operating. That's inconvenient, since the plug isn't always in view. A couple of times I forgot to plug the charger into the mains and only noticed after a while that it wasn’t charging. There’s also no on/off button. Since the device connects to the mains via a power cord rather than directly, the lack of a button is a drawback.
There are no feet on the case, so the charging station slides easily across the table. It’s not a major inconvenience; to some extent, the cables keep the charger in place.
I found a “bug” inside the PA-T15. I could hear it if I held the device up to my ear and shook it. I’ll tell you what happened to it a little later.
The charging station weighs 155 g without the cable.

After unpacking, I took a few photos of the charging stations, did some basic testing, and compared them. Then I gave one of the stations to a colleague. It was time to start detailed testing of the PA-T15. Unfortunately, an unpleasant surprise awaited me: the charger didn’t work, and none of the USB ports output any voltage. The “bug” inside had gone quiet too, which made me suspect the two events were connected. The seller turned out to be decent and got back to me fairly quickly, asking for a video confirming the fault for their “technical specialists.” Defects happen with every manufacturer, so I took it in stride and ordered another PA-T15 charging station as compensation. Luckily, delivery is fast. I had to finish the tests!
There’s a big upside to this unpleasant situation! I now had a chance to take the device apart without worrying about damaging its appearance. Let’s move on to the teardown and take a look at the charging station’s internals.
To access the circuit board, you need to remove the back cover. This is very difficult; a hot-air rework station and plastic pry tools helped me. The cover sits quite deep, and it feels as though it’s welded to the case at some points.

The “bug” that had gone quiet was easy to find during inspection. It turned out to be a ball of solder stuck to the soft pad between the heatsink and the USB ports. Most likely, it had been moving freely around inside the device before, and shorted something. It could only move around on the component side of the board; it couldn’t get to the side with the SMD components.


The soldering around the USB ports is very poor; they were probably touched up by hand. The board has a whitish flux residue. There are no slots separating the high-voltage section. If you look closely, there’s an arc mark near the power transistor leads, which is probably where the short occurred. The outer layer of resistors R112–R116 shows signs of burning.







The input has a thermistor to limit inrush current and a fuse.


Unfortunately, the input filter components are missing, even though the board has footprints for them.

The D4UB100 bridge rectifier has plenty of voltage and power headroom.

The filter capacitor is rated at 100 µF and 400 V. Its capacitance is sufficient for the power supply’s stated output power.

The power transistor ISA10N60A is mounted on a small heatsink. A continuity test confirmed that it had failed short.

The transformer is clearly visible in the overview photo of the board. A proper Y-class safety capacitor is installed next to it.

I haven’t identified the PWM controller yet; it’s also clearly visible in the overview photo of the board.
This photo shows a close-up of the feedback optocoupler and the damaged R104 and R105 resistors.

Output filter capacitors.

The NCE80H16 MOSFET and 20T200CT Schottky diode share a heatsink.

MP6901 flyback converter and LM321 operational amplifier.

Each USB port has its own CW3042 chip for AiPower. That's good: it means each port is controlled and operates independently, as the tests will confirm later. The manufacturer's website says the CW3042 is a USB charging controller with current limiting. It supports Battery Charging v1.2 Spec and other standards, such as Apple's charging specification (for iPad and iPhone) and the Samsung Galaxy family. The maximum continuous current is 2.8 A (which is well within Aukey's stated figures); overload protection kicks in at 3.17 A.

A different chip controls the USB port with QC3.0. Most likely, it's an NCP4371.

There's another chip nearby. It looks like an operational amplifier from Analog Devices.

Just for the fun of it, I want to repair the board. I'll need to replace the power transistor, about ten resistors, and possibly the PWM controller. I haven't found the time to look into it in detail yet, but someone on the forum suggested it's most likely an SG6848 or SP6853 in an SOT-23-6 package.
A few days later, I received a second Aukey PA-T15 to replace the one that had burned out. It was delivered by the same courier company, IML, in similar packaging, and again there was no warranty card. There's no point posting more photos, so let's go straight to the tests. The USB tester readings are hard to make out in the photos, so I'll also write them out.
First, I'll check the output voltage of both chargers with no load.
The AUKEY PA-T15 outputs about 5 V on QC3.0 with no load.

The AUKEY PA-T1 also outputs about 5 V on QC2.0.

AiPower outputs 5.2 V on both chargers.

I decided to double-check the USB doctor with a multimeter. The readings match.


The tests from here on are for the AUKEY PA-T15 only.
The charger easily handles the stated 3 A on the QC3.0 output, with some headroom (3.5 A), at 5.19 V.

When I connect a higher-power load, the charger lowers the voltage as a protective measure.

Here, both load controls are turned all the way up, and the charger has lowered the voltage further.

My USB doctor has a very convenient reversible USB connector, but the data contacts are wired to only one side of it.

So when I connect an iPhone through the USB doctor, this is what happens. It doesn't charge in this orientation.

If I plug the USB doctor in the other way around, rotated 180 degrees, charging works normally. The iPhone draws about 1 A at 5.11 V from the AiPower output.

The QC3.0 output works the same way with the iPhone.

I don't have a trigger to switch the charger into QC3.0 mode. I planned to test it in QC2.0 mode with a Samsung Galaxy S7. I'd already tested the first PA-T15 in this mode, and everything worked, although the voltage on the QC3.0 output was a little below 9 V, around 8.9 V.
Unfortunately, the new charger wouldn't work in QC3.0 mode. When I enabled fast charging in the phone's settings, the QC3.0 output was only 5 V and 0.5 A. I checked the cable and USB doctor with the original Samsung charger, and everything works as it should. As I mentioned above, my USB doctor has a reversible USB connector, so I checked it in both orientations just in case. The result was the same.

Another failure. That's a lot for a branded device.
Well, all that's left is to describe how the AiPower outputs work. Unfortunately, they don't work perfectly either.
1 A load, voltage around 5.1 V

At a load of 1.85 A, the charger still holds the voltage at 5 V.

At 2 A, the voltage on the AiPower outputs drops below 5 V (we could put this down to the Doctor's measurement error, although the multimeter shows similar readings).

At a load of 2.4 A, the voltage is 4.92 V. That's 1.6% below 5 V, which could of course also be attributed to measurement error. But comparing the readings from the instruments on the QC3.0 output and the AiPower outputs before connecting the load, the voltage is clearly sagging.

The AiPower port delivers a maximum of 2.78 A (at 4.82 V). If this figure is exceeded, the port shuts off. The other outputs keep working. I actually liked this type of protection better than the voltage drop on QC3.0. For example, my load can't start its fan when the voltage is below 4 V and quickly overheats. So be careful when connecting devices with active cooling to the QC3.0 port.

I'll test the charger by connecting as many loads as possible. I set the load to 3.5 A. At 5.1 V, it draws 17.85 W.

The power bank draws 0.92 A at 5.11 V, another 4.7 W.

The tablet draws 1.77 A at 5 V, which is 8.85 W.

Another load: 2.15 A at 4.96 V, which is 10.7 W.

In total, I managed to load the charger to 42 W out of the 54 W claimed by the manufacturer. It's quite difficult to achieve this kind of load in real-world conditions.
I ran the charger under load for an hour. The maximum case temperature (near the transistor's heatsink) settled at around 65 degrees. The heatsink and transistor themselves were clearly hotter, and at a higher load the temperature would rise further, which is not good.

In conclusion, I can say that the charging station didn't fully do its job. Although it's generally convenient to use, I don't plan to buy Aukey devices again.
Pros:
+ convenient form factor;
+ QC3.0 support (claimed, but categorically doesn't work for me);
+ reliable port overload protection;
+ independent operation;
Cons:
- poor soldering quality, resulting in problems with the station's operation;
- the high-voltage section of the board is not separated from the low-voltage section by a slot;
- short power cord included;
- voltage on AiPower drops below 5 V under load; with the additional drop across the cable, the phone will receive an even lower voltage.
- no on/off button (useful in some situations);
- no operation indicator.
Dmitry Savelyev
17.10.17
$21.72
This page was found when searching for:
протокол быстрой зарядки power delivery, зарядный блок aukey на 5 портов, aukey зарядное устройство обзор , ремонт aukey pa t15 зарядное устройство, Замкнуть D и D −, и подключить их к одному делителю, aukey pa-t1 ремонт, 2, aukey pa-t111 аналог, лучшее зарядное устройство с 5 usb портами, aukey 5usb с поддержкой qualcomm quick charge, crdc 5 портовое зарядное charge 3.0, aukey 5 port, aukey qualcomm quick charge короткий ролвод, устройство aukey на 5 usb, быстра, mp6901 charger, aukey pa t15 ремонт шим контроллер, aukey quick charge 3.0 usb, aukey зарядные устройства, aukey 1ac 3usb аналоги, зарядное устройство qc 3.0 aukey pa y5, aukey 5 usb qualcomm quick charge, что случилось с зарядными устройствами aukey?, aukey pa t5, aukey на 5 usb smart, aukey pa t15 отзывы
протокол быстрой зарядки power delivery, зарядный блок aukey на 5 портов, aukey зарядное устройство обзор , ремонт aukey pa t15 зарядное устройство, Замкнуть D и D −, и подключить их к одному делителю, aukey pa-t1 ремонт, 2, aukey pa-t111 аналог, лучшее зарядное устройство с 5 usb портами, aukey 5usb с поддержкой qualcomm quick charge, crdc 5 портовое зарядное charge 3.0, aukey 5 port, aukey qualcomm quick charge короткий ролвод, устройство aukey на 5 usb, быстра, mp6901 charger, aukey pa t15 ремонт шим контроллер, aukey quick charge 3.0 usb, aukey зарядные устройства, aukey 1ac 3usb аналоги, зарядное устройство qc 3.0 aukey pa y5, aukey 5 usb qualcomm quick charge, что случилось с зарядными устройствами aukey?, aukey pa t5, aukey на 5 usb smart, aukey pa t15 отзывы
Questions and answers
What load did the AUKEY PA-T15 charging station handle?
With several devices connected, the measured total load was 42 W, compared with the manufacturer's stated 54 W.
How hot does the AUKEY PA-T15 get under load?
After an hour of operation, the maximum case temperature near the transistor heatsink was about 65 °C.
What is the author's verdict on the AUKEY PA-T15 and Quick Charge 3.0?
The station is convenient to use but did not fully perform as intended: its advertised QC 3.0 support did not work in the author's test, and the soldering quality drew criticism.
The figures from this review are in the measurement database: Chargers
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments6
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.