Air conditioner power supply, or the story of a repair
I came across a faulty power supply and decided to jot down a note about repairing it, and while I was at it, answer a few questions people ask me, using a real example, so to speak.
I actually had two power supplies. They'd been lying around for a very long time, and I felt rather bad about it, especially since a friend had brought them to me.
They were originally installed in air conditioners. A voltage surge burned out both of them. Before they got to me, someone else had tried to repair them. I fixed one power supply a long time ago, and only just got around to the second one.

To be honest, I (and I'm not the only one) really don't like repairing equipment after someone else has worked on it. I'm not going to criticize them; they did the best they could, some better than others. And someone probably criticizes me too, and is just as right in their own way. The problem is that sometimes, after components have been replaced, you can't tell what was originally wrong. And sometimes a repair can make things worse, which means more work.

Originally, not only the varistors but also the fuses on the boards were intact. The problem came from the load side, not the mains.

The first step in a repair is always to ask the customer what happened before the problem started. Sometimes that helps diagnose it. Next, inspect the board for damaged components. The first thing I spotted was a blown high-voltage transistor. Judging by the shape of its leads, it wasn't the original part.

You can tell from the board that only this part had been replaced, since only its three pins had been soldered.

After the visual inspection, check the input section with a multimeter. And, just in case, discharge the input capacitor first. If some components have burned out, the capacitor can sometimes stay charged for a very long time.
Next, check for a short circuit before the bridge rectifier, and make sure the fuse and current-limiting resistor or thermistor are intact.
When there's a problem in the high-voltage section, the bridge rectifier or high-voltage transistor often fails. You can check this with a multimeter in diode-test mode, connecting it across the input capacitor. One way around, the reading should be infinite; the other way, you should see a voltage drop across the bridge rectifier diodes. If there's a short, desolder the high-voltage transistor first and check again. If the short is still there, the bridge rectifier is most likely to blame.

I was surprised that there was no short on the input, even though the transistor was clearly blown. It turned out the board was missing the current-sense resistor! There's a footprint for it, but no resistor. I don't know where it went, because all the SMD components on the board are glued down as well, making them difficult even to desolder.
This usually leads to bigger problems, because when the power supply is connected to the mains, the other components in it are exposed to high voltage.

And I was right: further inspection revealed at least three more burned resistors. After desoldering and testing them, I found that a small transistor in a SOT-23 package was also completely open-circuit. Repairing power supplies like this is tricky because the board is crowded with components that have nothing to do with the power supply itself, on both the "hot" and "cold" sides.

What do you do if components have burned so badly that you can't identify their values?
If they're through-hole parts, you can do what I recommended here.
If they're SMD, it's much more complicated. One option is to look for the original schematic, or the closest similar one, or draw it yourself.
Sometimes searching for similar schematics helps a lot, because power supplies are actually built around standard circuit designs. Unfortunately, this power supply is self-oscillating, meaning it doesn't have a PWM controller. Personally, I'm not a big fan of power supplies like this, but they certainly have their place.
Out of curiosity, I found a couple of schematics similar to the one this power supply is based on.


In my case, things turned out to be much simpler. I mentioned above that I had two power supplies, and my habit of photographing everything that comes my way during repairs really paid off.
Here's a photo of the other identical power supply.

The high-voltage transistor here had also been replaced by someone else, but with a different type. But the main thing is that almost all the other components are intact. The entire repair came down to replacing two parts, one of which was a current-sense resistor.
So I recommend making a habit of photographing everything. It may come in handy later, especially since these days there’s probably a camera even in a vacuum cleaner.

Here’s another rule that beginner radio enthusiasts often forget—and then ask me about: “My power supply (amplifier, TV) burned out. A transistor blew, I replaced it, but when I tried to turn it on, there was a bang.”
If you’ve found a faulty component, that doesn’t mean it’s the only one. Almost always, it takes several others with it. For example, a shorted high-voltage transistor usually takes out:
The current-sense resistor
The PWM controller
The gate-drive components
Sometimes the bridge rectifier and optocoupler, too.
That’s what happened here: as you could see above, several resistors had burned out. Two of them are in the optocoupler circuit, and if they’ve burned out, it’s best to replace the optocoupler as well, especially since it costs next to nothing. In this power supply, it’s hidden under the transformer.

Since I’d already desoldered the optocoupler and its surrounding components, I checked the capacitor connected in parallel with the optocoupler’s transistor. Its capacitance is 100 pF, which is perfectly normal for this circuit.
I also checked the secondary side for shorts and immediately found a short on the 12 V rail (the power supply outputs 5 V and 12 V).

Actually, I’m bending the truth a little here: the previous power supply had the same problem—a 12 V TVS diode had shorted. Removing it cleared the short. But I checked the secondary side then, too, so the recommendation still stands and applies to the question: “I replaced all the components on the primary side, but the power supply won’t start.”

So, in addition to the blown high-voltage transistor, we have:
Three resistors
An auxiliary transistor
An optocoupler
A Zener diode
I rummaged around at home and found some more or less suitable components:
I used an 8.2 Ω resistor instead of 10 Ω, 24 Ω instead of 22 Ω, and 3 kΩ instead of 3.3 kΩ. The optocoupler was a PC817, with the same pinout. The only problem was the small transistor: it was completely open-circuit. According to the SMD code table, it could be either a Zener diode, which didn’t make sense, or a logic-level transistor, which wasn’t much more plausible. In the end, I used a regular BC817.
The only component I bought was the high-voltage transistor IRFU420. I’m also often asked where I buy components.
I’ll say it again: I buy them locally, most often at our Kharkiv store Kosmodrom, because:
It’s quick
There’s a much better chance of getting a genuine component rather than a dummy with the same size and weight.

Solder the components in. At this stage, there’s no need to wash the board, since you may still need to desolder something.

Another problem with boards like these is that they often don’t have any standard power connectors. For example, this one has three wires coming out—black, red, and green—but the power actually goes to the black wire and a terminal on the board.

You can usually figure out where the power goes by simply tracing the tracks to the bridge rectifier. Having a common-mode choke helps a lot. At this stage, the fuse and current-limiting resistor don’t matter.

Connect the power supply through a 15–25 W incandescent bulb and check the output voltage. No issues—the voltage is normal. You can test small power supplies under full load by replacing the bulb with a higher-wattage one, say 150 W, but only for low-power supplies, around 10–15 W.
Also, connecting it through a small bulb lets you see how much input current it draws with no load. If the bulb glows noticeably, something’s wrong.

Now we can solder in the protective Zener diode. The original was marked B15, not 15 V, as people sometimes mistake it for. Although that would actually be more convenient, since it would mean a 15 V Zener diode—but B isn’t a voltage rating; it’s the Zener diode type.

Since this is an air conditioner power supply, and may therefore be used in high humidity, I coat the board with protective varnish after washing it, just to be safe.

That’s about it. Once it’s dry, it’s ready to use.

The repair isn’t actually finished, since I can’t fully test the board because of the device’s specific design. In other words, to test it properly, I’d have to install it in the air conditioner and see how it behaves. Something else unrelated to the power supply itself may have failed, too.
But for the most part, the repair is finished. I hope it was useful.
I actually had two power supplies. They'd been lying around for a very long time, and I felt rather bad about it, especially since a friend had brought them to me.
They were originally installed in air conditioners. A voltage surge burned out both of them. Before they got to me, someone else had tried to repair them. I fixed one power supply a long time ago, and only just got around to the second one.

To be honest, I (and I'm not the only one) really don't like repairing equipment after someone else has worked on it. I'm not going to criticize them; they did the best they could, some better than others. And someone probably criticizes me too, and is just as right in their own way. The problem is that sometimes, after components have been replaced, you can't tell what was originally wrong. And sometimes a repair can make things worse, which means more work.

Originally, not only the varistors but also the fuses on the boards were intact. The problem came from the load side, not the mains.

The first step in a repair is always to ask the customer what happened before the problem started. Sometimes that helps diagnose it. Next, inspect the board for damaged components. The first thing I spotted was a blown high-voltage transistor. Judging by the shape of its leads, it wasn't the original part.

You can tell from the board that only this part had been replaced, since only its three pins had been soldered.

After the visual inspection, check the input section with a multimeter. And, just in case, discharge the input capacitor first. If some components have burned out, the capacitor can sometimes stay charged for a very long time.
Next, check for a short circuit before the bridge rectifier, and make sure the fuse and current-limiting resistor or thermistor are intact.
When there's a problem in the high-voltage section, the bridge rectifier or high-voltage transistor often fails. You can check this with a multimeter in diode-test mode, connecting it across the input capacitor. One way around, the reading should be infinite; the other way, you should see a voltage drop across the bridge rectifier diodes. If there's a short, desolder the high-voltage transistor first and check again. If the short is still there, the bridge rectifier is most likely to blame.

I was surprised that there was no short on the input, even though the transistor was clearly blown. It turned out the board was missing the current-sense resistor! There's a footprint for it, but no resistor. I don't know where it went, because all the SMD components on the board are glued down as well, making them difficult even to desolder.
This usually leads to bigger problems, because when the power supply is connected to the mains, the other components in it are exposed to high voltage.

And I was right: further inspection revealed at least three more burned resistors. After desoldering and testing them, I found that a small transistor in a SOT-23 package was also completely open-circuit. Repairing power supplies like this is tricky because the board is crowded with components that have nothing to do with the power supply itself, on both the "hot" and "cold" sides.

What do you do if components have burned so badly that you can't identify their values?
If they're through-hole parts, you can do what I recommended here.
If they're SMD, it's much more complicated. One option is to look for the original schematic, or the closest similar one, or draw it yourself.
Sometimes searching for similar schematics helps a lot, because power supplies are actually built around standard circuit designs. Unfortunately, this power supply is self-oscillating, meaning it doesn't have a PWM controller. Personally, I'm not a big fan of power supplies like this, but they certainly have their place.
Out of curiosity, I found a couple of schematics similar to the one this power supply is based on.


In my case, things turned out to be much simpler. I mentioned above that I had two power supplies, and my habit of photographing everything that comes my way during repairs really paid off.
Here's a photo of the other identical power supply.

The high-voltage transistor here had also been replaced by someone else, but with a different type. But the main thing is that almost all the other components are intact. The entire repair came down to replacing two parts, one of which was a current-sense resistor.
So I recommend making a habit of photographing everything. It may come in handy later, especially since these days there’s probably a camera even in a vacuum cleaner.

Here’s another rule that beginner radio enthusiasts often forget—and then ask me about: “My power supply (amplifier, TV) burned out. A transistor blew, I replaced it, but when I tried to turn it on, there was a bang.”
If you’ve found a faulty component, that doesn’t mean it’s the only one. Almost always, it takes several others with it. For example, a shorted high-voltage transistor usually takes out:
The current-sense resistor
The PWM controller
The gate-drive components
Sometimes the bridge rectifier and optocoupler, too.
That’s what happened here: as you could see above, several resistors had burned out. Two of them are in the optocoupler circuit, and if they’ve burned out, it’s best to replace the optocoupler as well, especially since it costs next to nothing. In this power supply, it’s hidden under the transformer.

Since I’d already desoldered the optocoupler and its surrounding components, I checked the capacitor connected in parallel with the optocoupler’s transistor. Its capacitance is 100 pF, which is perfectly normal for this circuit.
I also checked the secondary side for shorts and immediately found a short on the 12 V rail (the power supply outputs 5 V and 12 V).

Actually, I’m bending the truth a little here: the previous power supply had the same problem—a 12 V TVS diode had shorted. Removing it cleared the short. But I checked the secondary side then, too, so the recommendation still stands and applies to the question: “I replaced all the components on the primary side, but the power supply won’t start.”

So, in addition to the blown high-voltage transistor, we have:
Three resistors
An auxiliary transistor
An optocoupler
A Zener diode
I rummaged around at home and found some more or less suitable components:
I used an 8.2 Ω resistor instead of 10 Ω, 24 Ω instead of 22 Ω, and 3 kΩ instead of 3.3 kΩ. The optocoupler was a PC817, with the same pinout. The only problem was the small transistor: it was completely open-circuit. According to the SMD code table, it could be either a Zener diode, which didn’t make sense, or a logic-level transistor, which wasn’t much more plausible. In the end, I used a regular BC817.
The only component I bought was the high-voltage transistor IRFU420. I’m also often asked where I buy components.
I’ll say it again: I buy them locally, most often at our Kharkiv store Kosmodrom, because:
It’s quick
There’s a much better chance of getting a genuine component rather than a dummy with the same size and weight.

Solder the components in. At this stage, there’s no need to wash the board, since you may still need to desolder something.

Another problem with boards like these is that they often don’t have any standard power connectors. For example, this one has three wires coming out—black, red, and green—but the power actually goes to the black wire and a terminal on the board.

You can usually figure out where the power goes by simply tracing the tracks to the bridge rectifier. Having a common-mode choke helps a lot. At this stage, the fuse and current-limiting resistor don’t matter.

Connect the power supply through a 15–25 W incandescent bulb and check the output voltage. No issues—the voltage is normal. You can test small power supplies under full load by replacing the bulb with a higher-wattage one, say 150 W, but only for low-power supplies, around 10–15 W.
Also, connecting it through a small bulb lets you see how much input current it draws with no load. If the bulb glows noticeably, something’s wrong.

Now we can solder in the protective Zener diode. The original was marked B15, not 15 V, as people sometimes mistake it for. Although that would actually be more convenient, since it would mean a 15 V Zener diode—but B isn’t a voltage rating; it’s the Zener diode type.

Since this is an air conditioner power supply, and may therefore be used in high humidity, I coat the board with protective varnish after washing it, just to be safe.

That’s about it. Once it’s dry, it’s ready to use.

The repair isn’t actually finished, since I can’t fully test the board because of the device’s specific design. In other words, to test it properly, I’d have to install it in the air conditioner and see how it behaves. Something else unrelated to the power supply itself may have failed, too.
But for the most part, the repair is finished. I hope it was useful.
This page was found when searching for:
ch25g/qtpgdp.k отличие от ch25g/qlpgdp.k, pcb-htsd008 коды ошибок, кудато пропадает 220 на плате уличного блока кондицеонера как отремонтировать, схема. платы. управления. кондиционера. фуджитсу. 9, de00n300 схема, плата lh-ch25g/y2pg, блок питания платы управления кондиционера, hc2702d отладка, куда подается питание на плате m526f2jv1 grj526-a, схема платы кондиционера м504f, трансформатор кондиционера самсунг назначение, как выглядит транзистор блока питания на кондиционере минцабиси хеви, блок питания кондиционера mitsubishi транзистор n4, rfr pfvtybnm cujhtdibq ghtlj[jfybntkm yf cgkbncbcntvt cfvceyu, замена бп на кондиционере, hc2702d, lh-ch25g/y2pg 1/2 подключить, сгорел блок питания у кондиционера, схема блока питания в кондиционере, на плате кондиционера транзистор, схема электрическая блока питания кондиционера one concept electronic star, lh-ch25 y2 p3 1 2 не включается, LH-CH25G/Y2PG(1/2), как заменить трансформатор питания в сплите, hc2702f 12 вольт
ch25g/qtpgdp.k отличие от ch25g/qlpgdp.k, pcb-htsd008 коды ошибок, кудато пропадает 220 на плате уличного блока кондицеонера как отремонтировать, схема. платы. управления. кондиционера. фуджитсу. 9, de00n300 схема, плата lh-ch25g/y2pg, блок питания платы управления кондиционера, hc2702d отладка, куда подается питание на плате m526f2jv1 grj526-a, схема платы кондиционера м504f, трансформатор кондиционера самсунг назначение, как выглядит транзистор блока питания на кондиционере минцабиси хеви, блок питания кондиционера mitsubishi транзистор n4, rfr pfvtybnm cujhtdibq ghtlj[jfybntkm yf cgkbncbcntvt cfvceyu, замена бп на кондиционере, hc2702d, lh-ch25g/y2pg 1/2 подключить, сгорел блок питания у кондиционера, схема блока питания в кондиционере, на плате кондиционера транзистор, схема электрическая блока питания кондиционера one concept electronic star, lh-ch25 y2 p3 1 2 не включается, LH-CH25G/Y2PG(1/2), как заменить трансформатор питания в сплите, hc2702f 12 вольт
Questions and answers
Which parts failed in the air-conditioner power supply?
Besides the high-voltage transistor, the author found three burnt resistors, an auxiliary transistor, an optocoupler and a shorted Zener diode in the 12 V circuit.
How did the author test the repaired air-conditioner power supply?
The unit was connected through a 15–25 W lamp, and its output voltage was normal. A complete test requires installing it in the air conditioner.
Why take photos of a power-supply board during repair?
Photos can help restore the original component layout and identify missing parts. Here, a picture of a second identical unit helped show what the damaged board should contain.
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments8
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister



Comments are published in their original language.