How to Choose an IR Soldering Station
But today we’re not talking about soldering irons, but about much more sophisticated equipment designed not for home use, but rather for professional applications.
A reminder: to keep up with new topics on the blog, I recommend following me on Instagram. I’ll post notifications about all new topics there, and might also write about something interesting from time to time - link to account
You can also subscribe to updates and new articles on the Telegram channel - https://t.me/KirichBlog
First, it’s worth clarifying that the term “soldering station” usually refers to both temperature-controlled soldering irons with various auxiliary modes, hot-air stations, and more sophisticated equipment that can operate almost automatically.
This article is about stations that make it easier to solder and replace chips in BGA packages.
BGA (Ball Grid Array) is a method of mounting chips in which the connections are made through solder balls instead of the familiar leads. More and more chips use this package these days, so soldering stations designed for them are becoming increasingly relevant.

With enough determination, you can replace a chip in a BGA package using an ordinary heat gun and an iron, but the reliability and quality of the work would be questionable. What’s more, some DIYers even build their own stations using a temperature controller.

The point is that, in addition to top and bottom heating, you need to follow the thermal profile specified in the component’s documentation, and a proper station should do this automatically.
For example, the diagram below shows two cases. On the left, heating is too fast: the chip package is already hot while the contacts are still cold. This overheats the chip. On the right, the heating rate is correct, so the balls have time to heat up before the chip overheats.

Expensive stations may have multi-zone bottom heating, allowing different temperatures to be set—for example, higher around the chip being installed and lower in the surrounding areas.

Broadly speaking, stations can be divided into three classes:
1. Manual: all operations are performed by hand; the station only heats the chip.
2. Semi-automatic: heating and cooling are automated, while chip removal and installation are done by hand.
3. Automatic: all operations are automated.
Stations may also have additional features, such as a camera to make it easier to align the chip with its position on the board, or a computer connection for convenient work with thermal profiles and software updates. Heater power and the availability of forced board cooling also vary.
Let’s start with the simpler options, such as the Ly M770 station, which is more of a soldering platform.
The station is very basic and aimed more at “home” use—that is, situations where you only need to work occasionally, so the operator controls every step manually.

The station includes:
1. A chassis with a mechanism for securing circuit boards
2. An adjustment mechanism for the top heater
3. A pair of bottom IR heaters rated at 800–850 W each
4. A 250 W top heating element
5. Two independent temperature controllers
6. An adjustable thermocouple for measuring the top temperature
7. LED lighting
All operations are performed manually; there are no thermal profiles, but that’s the unavoidable trade-off for the low price.
Even so, this station can already remove and install BGA chips on boards up to 500x450 mm, and you’ll find all the components shown below in expensive stations as well.

The ACHI IR 6500 soldering stations and Dinghua IR6500 (DH-A01R) are more interesting in terms of how well they work. They look very similar, but have some differences:
ACHI IR 6500 - 1250 W (800 W bottom heating and 400 W top heating)
Dinghua IR6500 - 2300 W (1800 W bottom heating and 450 W top heating)
Both stations already have a useful feature: a computer connection via USB (ACHI IR 6500) or RS232 (Dinghua IR6500).
This feature makes it possible to work with thermal profiles that specify the required rate of temperature change and the target temperatures.
That is, The specifications of this station put it in the entry-level category, but it is already a fully capable station, which will of course have a positive effect on the results.
Otherwise, it is much the same as the previous model: preheaters, position adjustments and a work table. The ACHI IR 6500 can accommodate boards up to 400x305mm, while the Dinghua IR6500 supports boards up to 355x280mm. The maximum chip sizes also differ: 70x70 and 55x55mm, respectively.
Overall, the ACHI IR 6500 looks a little more attractive. It connects via USB, and both its table and maximum chip size are larger. Its only real drawback is that its heaters have lower power.

A compromise option is the LY IR8500 station. It can also accommodate boards up to 400x305mm, work with chips up to 70x70mm, and connect to a computer via RS232, but its power is limited to 2050W (1600W for the bottom preheater and 450W for the top heater).

The Dinghua DH-5830 station, on the other hand, can confidently be classed as a professional model, albeit an entry-level one. It differs from the previous stations in several important ways:
1. 5200W of power (1200W bottom preheater, 1200W top heater and 2800W auxiliary heater)
2. A touchscreen that makes it easier to operate the station without a computer (though computer control is also available)
3. The minimum chip size it can handle is just 2x2mm!
4. Maximum chip size: 80x80mm.
5. Stores up to 50000 thermal profiles.

Another genuinely important difference is the third heater, located in the center. It makes the job easier by heating the board only beneath the chip being worked on. The large heater warms the entire board to prevent thermal deformation caused by areas with large temperature differences.

The diagram shows how it works, with all three heating zones visible.

There is also an upgraded version of the station shown above, the Dinghua DH-A1L-C. For easier operation, it adds optical monitoring, with the image displayed on a monitor. Otherwise, the stations are practically identical.
Of course, you can manage without a camera, but trying to see what is happening in the narrow space between the board and the top heater is not only inconvenient but dangerous, since the temperature is very high.

Stations like these also use special fans to cool the board, rather than ordinary ones. They can blow air evenly across the entire width of the board. The more uniform the cooling (and heating), the less the board is prone to warping due to uneven surface temperatures. These fans are used to reduce that warping. You may have seen them in air conditioners, too.

And so, step by step, we have arrived at professional stations. The price is noticeably higher, so few people are likely to buy one for home use, but they are well within reach for a repair shop or service center.
Let's start with the WISDOMSHOW WDS-620 soldering station. It includes the same components as all the stations shown earlier, but also adds a few features.
1. Maximum chip size is limited to 50x50mm, but the minimum is just 0.8x0.8mm.
2. Maximum PCB size is 400x380mm; the minimum is just 10x10mm.
3. Power: 5300W

Unlike the previous stations, this one offers a higher degree of automation, with an automatic vacuum-pickup system, laser positioning of the heater, and optical positioning of the chip.
Yes, the monitor on this and the following stations is not for monitoring the process; it is used to position the chip relative to the PCB pads. Two images are displayed on the monitor at once: the pads and the chip contacts. You then use the adjustments to align them for precise placement.

All you have to do is install the PCB, select an operating mode, and position the chip pickup and placement system. The station will then perform almost all the operations by itself.

I could go on describing its features, but I think it would be more interesting to watch a video demonstrating chip removal and installation on a PCB.
If you need to work with larger chips and boards, it is worth considering the Dinghua DH-A2 station. It largely shares the features and capabilities of the WDS-620 station, but supports boards up to 450x430 and chips up to 80x80 mm. It’s worth noting that chips of this size are uncommon, so buying a station like this is more of a future-proofing move.

Dinghua DH-A2E, which is externally identical to the Dinghua DH-A2, has a carbon heater designed to provide even more uniform heating and a longer service life. Otherwise, the two stations are identical.

Like the WISDOMSHOW WDS-620, both stations have a monitor that displays the camera feed for precise chip positioning before automatic placement.

The article wraps up with the WISDOMSHOW WDS-750 automatic soldering station WISDOMSHOW WDS-750, which, in addition to all the features listed above, offers the following:
1. Handles chips as small as 0.2x0.4 mm
2. Supports boards up to 550x480 mm
3. Total power up to 6800 W
4. Picks up chips from a special tray, which is also where the removed chip is placed.
5. For precise positioning, it uses a 5-megapixel camera; the system can also operate as a digital microscope with up to 200x magnification.
6. Chip placement accuracy of up to 0.01 mm and temperature control accuracy of 1 degree.
In practice, this is no longer just a soldering station, but a complete system that can operate automatically in three modes: Weld – soldering, Remove - desoldering, Mount - desoldering and positioning the system relative to the circuit board.

Before the war, stations from the Russian manufacturer Termopro were available here; I think GSM-service sold them. For example, their entry-level station, which is really more of a “soldering platform,” costs only a little less than the Dinghua DH-5830. The DH-5830 already has a touchscreen, supports thermal profiles without a PC, and has two bottom heating zones.
The more advanced version (on the right) costs about as much as the Dinghua DH-A1L-C, but looks like a collection of separate modules.
With this company leaving our market, I’d suggest that anyone who knows this kind of equipment well consider making their own soldering stations. I don’t think it’s all that difficult, although of course there are plenty of pitfalls.

I’ll also mention that I was surprised to see that Elektronny Mir is now selling soldering stations, for example, the Quick 7710. Well, I wish them success—it’s a useful business.

As mentioned above, each step up from the simplest station to the most advanced adds a few features, while everything that came before remains almost unchanged. So when choosing, you should base your decision on your own use case.
Ly M770 - the simplest option, with top and bottom heating and temperature control.
ACHI IR 6500 and Dinghua IR6500 (DH-A01R) - PC connectivity and thermal profile support added
LY IR8500 - larger working area
Dinghua DH-5830 - thermal profile support without a PC and two bottom heating zones
Dinghua DH-A1L-C - a camera for monitoring the process and a fan spanning the full width of the work area added
WISDOMSHOW WDS-620 - optical and laser alignment added, with more power and a smaller minimum chip size.
Dinghua DH-A2 - increased maximum chip size.
Dinghua DH-A2E - carbon heater instead of a conventional one
WISDOMSHOW WDS-750 - even more power, an even smaller minimum chip size, support for larger boards, and a higher degree of automation.
Now all that’s left is to choose the station that offers the best balance between the tasks you need to handle and the price.
ir6500. верхний инфракрасный подогреватель, лучшая паяльная станция ик, инфракрасный пайка, инфракрасная паяльная станция 3650вт камера обзор, лазерная паяльная станция или инфракрасная паяльная станция, 9, ir8500 v.2 отзовы, dinghua dh-380, ик BGA станция: выбираем что купить 2024, https://www.kirich.blog/stati/zametki-na-polyah/1207-kak-vybrat-ik-payalnuyu-stanciyu, ик паяльная станция dinghua ir6500 dh-a01r
Questions and answers
How do the classes of IR rework stations for BGA differ?
On manual stations, the operator controls every step; semi-automatic models automate heating and cooling, while automatic models automate the entire process.
What are the power ratings of the ACHI IR 6500 and Dinghua IR6500?
The ACHI IR 6500 is rated at 1250 W, with 800 W of bottom heating and 400 W of top heating. The Dinghua IR6500 is rated at 2300 W, with 1800 W bottom heating and 450 W top heating.
What sets the Dinghua DH-5830 apart from simpler stations?
It has 5200 W of power, a touchscreen, storage for up to 50000 thermal profiles, and three heaters, including a central one. It can work with chips from 2kh2 to 80kh80 mm.
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments7
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.