/       /    IC for a Li-Ion battery charger.
Support the project on Patreon


IC for a Li-Ion battery charger.

$0.82
Go to store
I liked these small ICs for simple chargers. I bought them at a local brick-and-mortar store, but, as luck would have it, they ran out, and it took them a long time to get more from somewhere. Seeing how things were going, I decided to order a small batch for myself, since the ICs are pretty good and I liked working with them.
Description and comparison after the jump.

I mentioned the comparison in the title for a reason: while the package was on its way, the dog could have grown up the chips showed up in the store, so I bought a few and decided to compare them.
There won't be much text in this review, but there will be plenty of photos.

But, as always, I'll start with how it arrived.
It came together with various other components. The chips themselves were packed in a resealable bag with a label showing the name.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

This IC is a charger for lithium batteries with a charge termination voltage of 4.2 V.
It can charge batteries at up to 800 mA.
The current is set by changing the value of an external resistor.
It also supports low-current charging when the battery is deeply discharged (voltage below 2.9 V).
Once the battery reaches 4.2 V and the charging current drops below 1/10 of the set value, the IC stops charging. If the voltage drops to 4.05 V, it resumes charging.
There is also an output for connecting an indicator LED.
You can find more information in the datasheet. There is a much cheaper equivalent for this IC.
It's actually cheaper here; on AliExpress, it's the other way around.
So I bought the equivalent for comparison.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

But I was surprised to find that the LTC and STC chips looked exactly the same, and both were marked LTC4054.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

Well, maybe that's even more interesting.
As you can imagine, you can't test an IC on its own; it needs a few other components around it, preferably on a circuit board, and so on.
As it happens, a friend asked me to fix (or, in this case, probably modify) a charger for 18650 batteries.
The original one had burned out, and the charging current was too low anyway.

So, to test the chips, I first need to build something to test them with.

I laid out the board from the datasheet, without even drawing a schematic, but I'll include one here for convenience.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

And here's the PCB. Diodes VD1 and VD2 aren't on the board; I added them later.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

I printed all this out and transferred it onto a scrap piece of PCB laminate.
To save material, I made another board on the same scrap piece. I'll review that one later.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

And here's the finished PCB, with the required components selected.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

And this is the charger I'm going to modify. I'm sure many readers will recognize it.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

Inside, it has a very complex circuit consisting of a connector, an LED, a resistor, and specially trained wires that balance the charge between the batteries.
Just kidding—the charger is in the little plug-in adapter. This part just has 2 batteries connected in parallel and an LED permanently connected to them.
We’ll come back to the original charger later.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

I soldered the little board, pried out the original board with its contacts, and desoldered the contacts and springs themselves—they’ll come in handy later.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

I drilled a couple of new holes. The middle one will hold an LED indicating that the device is on, and the side holes will indicate charging.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

I soldered the contacts with their springs and the LEDs onto the new board.
It’s easiest to insert the LEDs into the board first, then carefully fit the board into its original position, and only then solder them. That way, they’ll sit straight and at the same height.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.


IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

The board is in place, and the power cable is soldered on.
The PCB was designed to support three power-input options.
Two options use a MiniUSB connector, with the connector mounted on either side of the board, and the third uses a cable.
In this case, I didn’t know at first how long a cable I’d need, so I soldered on a short one.
I also soldered the wires going to the batteries’ positive terminals.
They now run as separate wires, one for each battery.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.

Here’s how it turned out from above.

IC for a Li-Ion battery charger.IC for a Li-Ion battery charger.


The chips are clearly identical, which is definitely something to be happy about :)

I noticed that at 4.8 V the charging current is 600 mA, while at 5 V it drops to 500 mA. But I checked this after the chips had warmed up, so perhaps this is the overheat protection kicking in. I haven't figured it out yet, but the chips behave more or less the same.

Now, a little about the charging process and a further tweak to the modification (yes, that happens too).
At first, I thought I'd simply add an LED to indicate that the device was on.
Seems simple and obvious enough.
But, as always, I wanted more.
I decided it would be better if the LED went out while charging.
I added a couple of diodes (VD1 and VD2 in the schematic), but hit a snag: the LED indicating charging stayed on even when there was no battery.
Well, it didn't stay on exactly—it flickered rapidly. I added a 47 µF capacitor in parallel with the battery terminals, after which it started flashing very briefly, almost imperceptibly.
That's the hysteresis for restarting charging when the voltage drops below 4.05 V.
Anyway, after this tweak everything worked perfectly.
While the battery is charging, the red LED is on and the green one is off; when there's no battery, the LED is off too.

Chip for a Li-Ion battery charger.Chip for a Li-Ion battery charger.

The battery is fully charged.

Chip for a Li-Ion battery charger.Chip for a Li-Ion battery charger.

When switched off, the chip doesn't pass voltage to the power connector and isn't affected if that connector is shorted. It also doesn't drain the battery through its LED.

Chip for a Li-Ion battery charger.Chip for a Li-Ion battery charger.

I also measured the temperature.
After 15 minutes of charging, I got just over 62 degrees.

Chip for a Li-Ion battery charger.Chip for a Li-Ion battery charger.

And here's what the finished device looks like.
The external changes are minimal, unlike the internal ones. My friend already had a pretty decent 5 V, 2 A power supply.
The device provides a charging current of 600 mA per channel; the channels are independent.

Chip for a Li-Ion battery charger.Chip for a Li-Ion battery charger.

And this is what the original charger looked like. My friend wanted to ask me to increase its charging current. It couldn't even handle the original current, so why increase it? Junk.

Chip for a Li-Ion battery charger.Chip for a Li-Ion battery charger.

Summary.
For a chip that costs 7 cents, it's pretty good, in my opinion.
The chips are fully functional and no different from the ones bought locally.
I'm very happy with them. Now I have a stock of chips and don't have to wait for them to show up in the store (they recently disappeared from sale again).

The downside is that this isn't a ready-made device, so you'll have to etch the board, solder, and so on. But there's an upside: you can make a board for a specific application instead of using whatever happens to be available.

And in the end, you get a working device made with your own hands, cheaper than ready-made boards and tailored to your specific needs.
Almost forgot: the datasheet, schematic, and PCB layout are here.

I hope you found my review useful and interesting. :)
$0.82
Go to store
This page was found when searching for:
ax2539даташит, микросхема b07l2518, nh07ad, микросхема fae5a21e схема параметры, схема и datasheet fzh100, fm9919e datasheet на русском языке, sh3876014bp, микросхема fg5c, sh 167m, gw8025p микросхема, me4064 smd даташит как работает, n823050a datasheet, общий, fg5c микросхема цоколевка, микросхема gg1053, микросхема 82t807, ht 49 363 микросхема, 8953l схема включения, микросхема sb30 09, csc982h3 datasheet, cx3814, txm8953l описание схема, микросхемы для зарядников телефонов, yh-3635-2p-6j, gw8025p

Questions and answers

What charging current does the rebuilt 18650 charger provide?

It charges each battery at 600 mA, with independent channels.

Do the LTC4054 chips from Ali and the local store work alike?

They proved identical in the tests and behaved about the same.

How hot did the LTC4054 board get?

After 15 minutes of charging, its temperature was just over 62 °C.

The figures from this review are in the measurement database: Other devices

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments8

Comments are published in their original language.

  1. 6 January 2019 03:06#1
    Отличная статья!
    Вопрос такой, участвует ли данная микруха в процессе определения минимального порога заряда аккумулятора или же этот параметр задан программно устройством? К примеру видеорегистратор, акк заряжен 4.2В, при разряде до 3,7В питание отрубается, почему? Такая установка или может быть брак акка?
    0
    1. 6 January 2019 22:04#2
      Либо брак аккумулятора, либо некорректная установка порога в регистраторе, микросхеме зарядного все равно что там по разряду.
      0
      1. 6 January 2019 22:08#3
        Принял, спасибо! Как уже едет, скоро проверю кто виновник.
        -2
        1. 6 January 2019 22:09#4
          Обычно виновато высокое внутреннее сопротивление аккумулятора, кратковременные просадки и отключение по защите.
          +3
          1. 6 January 2019 22:15#5
            Радиогубитель я начинающий, отпаивали аккумулятор, у него напргуга была 1.5В, подпаял к креплению ЛиттоКалы, она его оживила до нужного значения. Сопротивление не запомнил, но видимо аккумулятор кабздец, исходя из отрубания на 3.7В.
            +1
            1. 7 January 2019 23:50#6
              Это просто самый распространенный сценарий. Немного продлить жизнь можно поставив приличную емкость параллельно питанию.
              +2
              1. Сергей
                24 February 2019 21:05#7
                Эти микрухи стояли в сотовых телефонах 2004х годов, в основном в самсунгах. Многие сотики в которых умирал свой контроллер заряда( в контроллере питания/проце итп)с их помощью отремонтиовал,правда телефон зачастую уже не знал,что идет заряд.... но это было экономически оправдано. Кстати,было несколько моделей самсунга у которых контроллер заряда находился в сетевой зарядке и был весьма "наворочен".
                +2
                1. 25 February 2019 22:08#8
                  Делал как-то давно блок питания для телефона, была такая мулька, стоит человек в переходе метро и предлагает за денежку звонить, а так как родного аккумулятора не хватало, то надо было внешний. Так вот с некоторыми моделями телефоном просто БП не виделся, работало с последовательно включенным резистором. 
                  +2

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister