/       /       /    A pair of electronic loads, or my experience buying from Taobao
Support the project on Patreon


A pair of electronic loads, or my experience buying from Taobao

$22.49+29.93 (без учета накладных расходов)
Go to store
I've already posted at least three reviews of electronic loads: a completely DIY one, one assembled from a kit, and a factory-made unit. In this case, both options are more like kits, since they aren't functionally complete products, even though they can work on their own; they do, however, need at least a power supply.
I spotted them almost a year ago and was interested, so I finally decided to buy them—and see what it's like to "buy on Tao".
Anyway, if you're interested in this topic, I think you'll find plenty of interesting things here.



Before getting to the review itself, here are links to my previous reviews on similar topics.
1. Completely DIY version + modification.
2. Kit version
3. Factory-made unit.

Part of the reason I wanted to buy one was that testing high-power power supplies had become difficult: my 300-400 W loads just weren't enough. Part of it was curiosity, and another reason was to try buying on Taobao, since you can find some really interesting things there.
At the end of the review, I'll share both my first buying experience and instructions for buying on Tao through the yoybuy.com agent.


There were no problems with the purchase, and after a while I received a fairly large package. I made a small mistake here: shipping isn't cheap, and my hardware is pretty heavy.


Everything was packed really well, but that was also a slight downside: the more packing material there is, the higher the shipping cost :(
In the second photo, you're not looking at two products, but one. The load is on the right, and on the left is what it was packed in.
The second load was packed even better, but in this case it was the seller's packaging—a soft little box.

No, it's all great. The agent not only packed everything well, but also emailed me beforehand, saying, "Dear Kirich, we've received two strange pieces of hardware, and we have no idea how to check them—we don't even know what they are..."
I replied, "Relax, don't panic. Compare them with the photos in the store; if they look roughly the same, send them along :)"



Anyway, I finally got my order, and in the end there were just two electronic loads on the table.


I'll start with the "dumb" one—that is, a load with no computer connectivity, just a basic load.
Rated power: up to 300 W
Voltage: up to 150 V
Current: up to 40 A
Modes: CCCV

There were lots of different options, which varied in voltage (150/60 V), current (10/20/30/40 A), and adjustment method: a connector on the board, a trimmer on the board, or an external potentiometer.


I went straight for the most "fully loaded" option, which was also the most powerful: 150 V, 40 A, 300 W, with an external potentiometer.
As you can see, the design consists of two essentially identical modules connected together. There's also a 150 W version made up of a single module.


By "external potentiometer," they mean a regular potentiometer on a small board. I'll get ahead of myself a little: there's no point ordering it this way. For convenient control, you should either order the 60 V version or, even better, install a multiturn potentiometer.


The cooling system (which is actually the heaviest part) consists of two fans and a special aluminum heatsink with air blown through it.
Five stars for the design. I wonder where I could get an aluminum extrusion like this—ideally 80x80 mm rather than 50x50 mm, or at least 60x60 mm.


A pair of fairly powerful, but also very noisy, fans covered by protective grilles. At first I thought, "What cheapskates—only two screws per grille." Then I realized there was nowhere to put the other two screws. Yep, cheapskates after all :)


Two control boards connected together—or, more accurately, not separated, since they're usually made this way.
A wire runs from one board to the other, and you can clearly see the idea: one board acts as the master and the other as the slave.


Most of the connectors are missing, but I'll try to explain what does what.
Ref - external voltage control, 0-5 V.
Potentiometr - external potentiometer; its wiper is connected to the same Ref, i.e. changes the voltage in the 0–5 V range.
Fan - fan connection; the wires are simply soldered on, with no connectors.
Con 1, the left-hand board has a connector soldered in - 12–15 V power.

There is also a spot for a 74HC connector. This is usually a designation for a family of logic ICs, but I don't know what it means here. One pin goes to ground, and four go to the microcontroller.
Con 4 - temperature sensor.


The other end of the board has power terminals for connecting the load, as well as:
Con 2 - essentially in series with the Vin power terminal. Most likely, a fuse is supposed to go here, but there's actually some kind of metal strip soldered in. Alternatively, you could connect an ammeter, but the connector looks rather flimsy for 20 A.
Con 3 - this connector provides ground, +12 V, and the Vin input voltage. You can connect a voltmeter here.
Fan 2 - connection for a second fan (exhaust), wired in parallel with the first one.


The load itself consists of four IRFP460A MOSFETs. That works out to 75 W per TO-247 package, which seems like a lot to me - a whole lot. The power rating is exceeded by at least 1.5 times. That's because MOSFETs work much harder in linear mode. That's why my own DIY load, rated for 400 W, uses 8 transistors, at 50 W per package - and even that is a bit much.

But I have to give them credit: the transistors are connected properly. Each transistor has not only its own shunt, but also its own op-amp. I used exactly the same approach in my version.


The board is secured with four screws and standoffs. The transistors have their own mounting hardware, and they didn't forget the thermal paste or the right screws with flat washers and split lock washers.
While taking it apart, I was half expecting the heatsinks to fall apart, but they held together - they seem to be glued to each other.
The standoffs could have been tightened a bit more, though...


From underneath, you can see more clearly how the boards are connected. By the way, for a more balanced connection of the power wires, connect the positive lead to one board and the negative lead to the other.


I have no real complaints about the power-terminal connections, but the enamel-insulated wires connecting the modules' power supply look completely wrong. I understand they're just tucked away in there, but one wire was touching a standoff and, over time, vibration would have worn through its insulation. Of course, you might ask where the vibration would come from. Well, there are two fairly powerful fans running, and that's all it takes for wires like these.


A closer look at one of the “halves.”



1. The power input is protected not only by a 1 A fuse, but also by a diode for reverse-polarity protection. They also added a whole bunch of capacitors across the power supply - surprisingly thorough :)
2. Although this is a “dumb” load, it still has a microcontroller. Here, it controls the operating modes, over-power protection, and the fan.
3, 4. Three LM321 op-amps. Two handle the current sensors and transistor control, while one (as far as I can tell) handles CV mode.

Speaking of fan control, it's been thought through quite well. When the load is cool, the fan is off. It switches on in stages when power exceeds 20–30 W per module, gradually increasing the airflow.
If you disconnect the load while the heatsinks are cool, the fans stop immediately. But if you heat them up first, the fans only stop once the temperature drops to around 35 degrees.
In other words, the fans are controlled in stages, based on both power and temperature.


A ceramic capacitor is connected across the input power terminals. My old one also has a capacitor, but with a noticeably higher capacitance, so it sometimes sparks a little when power is applied to the input.



There was a much smaller selection of options for the less powerful, “smarter” load: 60/150 V and 5/10/20 A. And once again, I went for the most powerful, highest-voltage option—and in this case, that may have been a mistake.

Link to this version, price depending on specifications: USD 17.47-22.49




The second load is noticeably smaller. I’d even say it’s quite small in its own way :)


It uses exactly the same fan and heatsink, which is hardly surprising—I’d have done the same myself.



The shunts and terminals for connecting to the source under test are on one side.
Although this one is rated for just 20 A, compared with 40 A for the previous one, the terminals are more substantial. Also, the right-hand terminal can be resoldered slightly differently, allowing you to connect an external ballast resistor to increase the power. The catch is that you’d have to reflash the controller, and there’s no firmware available :(
I later found out why the terminals are so beefy: this load is also available in versions rated for up to 30, 40, and even 50 A!


The control board is mounted on the right side and connected to the power board by a ribbon cable.


You can tell from the PCB that it’s designed for more. You can also see that each power transistor has its own current-balancing circuit.
There are a few flaws, though they’re minor in this case. The power trace connects to the transistors, while the sense trace should go directly to the shunt terminals. You can see this a little on the left pair of power traces. For the right-hand group of three, the signal is taken directly from the transistor lead, so the voltage is measured across the shunt plus the trace. Since copper resistance varies with temperature, the signal will drift. But because this circuit isn’t involved in measuring the load’s current, we can “understand and forgive.”


One important extra: there’s a third board here, a UART-RS485 converter. It has galvanic isolation and protection TVS diodes on the output. All in all, that gets a thumbs-up—it’s genuinely useful.
The seller says you can add a Bluetooth converter if you want. That would be quite useful, in my opinion.


I didn’t have a converter for connecting it to a computer handy, so I bought the cheapest one, for just 1.1 bucksat a nearby shop.
It’s built around a CH340 and MAX485. For just over a dollar, I think that’s great.

The connection is dead simple. The driver was already installed on my system, but if it isn’t on yours, it’s easy to find online.
Next, grab any bit of wire and connect A to A and B to B. That’s it. You’re supposed to use twisted-pair cable, but within an apartment, even a clothesline will work :)


Unscrew the standoff and the second screw, and you can remove the board for inspection.


Interestingly, there are lots of spots on the board covered with silicone. I’m not entirely sure why, since it comes off without much trouble. Maybe it’s meant to protect certain parts of the circuit from moisture, but that seems unlikely too.


The underside of the board is mostly empty, with very few traces. Most of it is a ground plane that acts as a shield.


The board has several footprints for connectors, allowing you to connect external devices.
First, there’s the UART, labeled ModbusRTU. As far as I understand, it uses the Modbus protocol for control, but so far my knowledge of it goes no further than reading the Wikipedia article.

Below that is the SPI connector. I assume it’s mainly for connecting a programmer.
Below that is a long row of pins, carrying the microcontroller’s ports and power.

I couldn’t figure out what SWIM is, a little to the right and above. It looks like some kind of jumper goes there, with the center pin connected to the microcontroller and the outer pins to ground and power. So you can set three signals this way: 1, 0, and Z. I tried all the options, but didn’t notice any difference.


The previous load was relatively simple, but this one has quite a few more components.
1. The “brains,” in the form of an STM microcontroller.
2. An ultralow-offset measurement op-amp, OP07, amplifies the signal from the main shunt.
3. The board also has a voltage converter LMC7660, which generates the negative supply rail for the op-amps. I built something similar into my electronic load, where I also used an OP07 + 7660 combination in the current measurement circuit.
4. The board also has two precision dual op-amps OPA2277.


And this is where things get a little strange.
There’s room on the board for two more op-amps, and all their supporting components are already installed, so you could simply solder in another pair of OPA2277s.
But the strangest thing is that the first pair of op-amps controls three transistors. Since the op-amps are dual, that leaves one section unused. I haven’t traced what it does; most likely it’s used either for voltage measurement or to control the next three op-amps.
Each transistor gets one op-amp section, since there are three transistors installed (I’ll show them below). There’s also room for two more transistors, but they only need one dual op-amp. Why add another one, especially with supporting components identical to those for the first pair? A mystery...


The input power protection circuit is the same as on the previous load: a resettable fuse, a reverse-polarity protection diode, and a bunch of capacitors.


Here are the three transistors I mentioned above. The board is designed for five transistors; you can even see two temperature sensors, one between the first and second transistors and the other between the fourth and fifth. Both sensors show up in the control software. Overall, this is a very sensible design—the manufacturer clearly decided to play it safe.
But these three transistors are from completely different batches. Nice :)
On the right, you can see the footprint for a second fan connector.


As I mentioned above, there are shunts on the left side of the board. The two U-shaped ones are measurement shunts for the controller itself; their readings are displayed in the software. There are two shunts out of five—the five-shunt configuration is probably used in the 50 A version.
To their right are three M-shaped shunts in the power transistor circuits. They’re used to balance the current through each transistor individually. Each shunt is paired with an op-amp, so the current is balanced very precisely. I used exactly the same approach in my high-power load, except that it has 8 transistors, 8 shunts, and 4 op-amps. This is the best way to do it, because it ensures that the current is shared evenly between the components. You can even use completely different transistors and the current will still be distributed evenly.


Interestingly, the product page has photos showing a funny combination: all the op-amps are installed and a wide ribbon cable is used, implying that all 5 transistors are fitted, but there’s only one measurement shunt and two balancing shunts.


I didn’t remove the fans when reviewing the more powerful load, but they look like the same ones. They’re fairly powerful 50 mm Delta fans rated at almost 3 W.
The fans are the main power consumers, so a 12 V, 0.3–0.35 A power supply is enough for this load, while the high-power version needs 12 V, 0.6 A.


Before moving on to the tests, I weighed both units. You’re probably wondering why, since they’re clearly not portable.
Because I ordered them through a forwarding service, weight matters quite a bit.
The total “net weight” was 1218 grams, and all the packaging weighed 318 grams, making the parcel’s total weight 1536 grams. By the way, the final weight exceeded the estimate, leaving me with an extra $1.30 to pay, but the forwarding service shipped the parcel anyway. When I asked what to do about the balance, they said it would be taken into account with my next purchase.



Since I inspected the high-power version first, I’ll test that one first, too.
Let’s connect the power supply and get started.


First, a few words about the controls.
Each module has its own button. A short press turns it on or off; a long press switches the operating mode. Here’s how it works:
1. If you hold the button down while the unit is off, it will start up in the second mode.
2. The load “remembers” the last mode used.

The first photo shows the correct combination: green-green. In this mode, CC mode is active.
If you turn on only the second load, nothing happens; it won’t work on its own.
The next two combinations may work, but they behave very erratically, so you shouldn’t use them. I’ll show you some examples later.


1. Connect it to a bench power supply and set the output to 30 V. The load is off.
2. Turn on the master unit (on the left) and set the load current to 1 A.
3. Switch on the slave unit. The current is 1.84 A, not 2 A as expected, which clearly indicates incorrect calibration.
4. Switch off the master unit. The current drops to zero; the slave cannot operate on its own.


Out of curiosity, I checked the minimum voltage drop across the load. Even including the cable, it was 0.64 V at a current of 5.1 A. I didn't think to measure the actual value, but calculations put it at around 0.5–0.6 V.


CV mode. This was one of the main reasons I bought these loads. You don't need this mode very often, but CC mode can't replace it.
To explain: when testing a power supply, it operates in CV mode (constant voltage), so you need to load it in CC mode (constant current). But when testing a charger, the situation is reversed: it operates in CC mode, so you need to load it with a load operating in CV mode.
This mode is more like a high-power Zener diode, or perhaps the equivalent of a battery connected to the charger under test.
And by charger, I mean an actual charger, not power supplies with USB outputs that are mistakenly called chargers.

So, here's what I found.
1. Set the power supply output voltage to 50–60 V. In this case, it was 54 V.
2. Turn the load control all the way to the right, then gradually turn it left until the power supply switches to constant-current mode. The load is now operating in CV mode, stabilizing the voltage at 52 V. If this were a regular power supply rather than a bench supply, it would simply trip its protection, since the load would be doing everything it could to prevent it from operating normally.
3. Turn the potentiometer to the left to lower the voltage further, for example to 16 V. The current readings in the photos differ; that's not a glitch. I took the photos during different experiments, and changed the bench supply settings along the way.
4. But I ran into the first problem: if you switch on the slave load, the voltage drops to zero. So the two units can't operate together in this mode.
5, 6. I managed to start the slave load in this mode, but it wasn't actually working—you could even tell because its fan didn't start. On top of that, the slightest change made it drop back into short-circuit mode.

So only the master load works in CV mode, which limits the power to 150 W rather than 300 W as in CC mode.
The second problem is that the load is rated for 150 V, and the entire range is covered in less than one turn of the potentiometer, so precise adjustment is out of the question. It's very coarse. The 60 V version would be more precise; with this one, I'll probably have to replace the potentiometer with a multiturn one.


I also tried different power levels. The load handles 250–300 W in CC mode without any problems, though it gets pretty loud. By the way, the fans are controlled independently, and sometimes you can hear one slow down while the other keeps running at full speed.
In CV mode, I managed to load it to 160–162 W. Beyond that, there was a short beep from the speaker and the load shut off. It ran reliably at around 155 W.


For the next experiment, I used the same setup as above, plus a USB-RS485 converter and a connecting cable.


I didn't take many photos during the process—and there wasn't much to photograph anyway—so what follows is a series of screenshots, tests, and some explanations and descriptions of the problems I ran into.

The product page had a link to the Chinese “Baidu,” where all the software needed to work with this module was available.
I changed the main program's name to something more sensible—DCL. Everything else is “as is.”


The same thing, but with the original filename and some additional information. As you can see, they provided a lot, but there's one problem: the antivirus and Windows 10 security (I tried Windows 7, 8, and 10) flag two files as Trojans. Both have the same red-square icon shown above. Since I still wanted to try them, I had to disable the antivirus and run everything at my own risk.


This is the software that launched. Or rather, this is what it should look like. I followed the link to the developer's page, where it says the software is an “experimental” version, so glitches are possible. The manufacturer makes various measurement modules, but I'll get to that toward the end of the review—that makes more sense.
So, here's an explanation of what's where in the software. Some of it was clear right away, some became clear during testing, and the rest only after translating it from Chinese.
1. Parameter input window.
2. Buttons for setting the parameter value, with increments of 100, 10, 1, 0.1, and 0.01, respectively. The first and last are generally not used. The top buttons increase the value, the bottom ones decrease it—pretty straightforward.
3. Buttons for entering calibration mode. I figured out what they do by accident; I'll explain below.
4. Operating mode selection - CC, CV, CW, CR
5. Select the COM port and device number on that port (RS485 supports multiple devices on one line).
6. Turn the load on/off.
7. Here I had to ask some Chinese managers I know, who also speak a language I understand better :). This is where you save the results to a file.


When I ran the software on my computer, everything was even more confusing. This is the software I had to figure out, to understand what everything did and why.
Exactly the same thing happened on all the computers and tablets at home.
I was especially baffled when I saw a current reading of 655 A.



But let's not dwell on the bad stuff. I'll explain the main operating modes.
1. CC: constant-current load. Set the current up to 20 A (the actual maximum is 20.1 A). If the power does not exceed 150 W, the load enters operating mode. If it does, it beeps and shuts off.
2. CV: the same thing, but you set the voltage limit. When you switch to this mode, the display shows a maximum of 151 V, which makes sense since you usually lower it rather than raise it.
3. CW: a fairly common mode, constant power. Set the power in watts, and the load will maintain that power draw from the source.
4. CR: a very rare mode in cheap devices, but fairly common in industrial ones. Here you can set the resistance of the “virtual resistor” represented by the load. In other words, the load current will depend directly on the source voltage. Unfortunately, this mode is very coarse and only lets you select resistance in 1 Ω increments.


I also found that the load starts up very gently, which can sometimes get annoying. For example, when you set the current to 3 A, it first jumps to about 2.3–2.3 A, then rises very gradually to the set value. It takes about 30 seconds in total.


Another problem I ran into was that the current reading wasn't calibrated. But every cloud has a silver lining. The voltage calibration was excellent. I was puzzled, though, by the two buttons to the right of the parameter-setting buttons. Clicking them brought up some incomprehensible numbers, like 4556 and 65432—clearly two different values. At first I thought they might enable simulated interference or ripple; the Greek letter mu threw me off. But at one “wonderful” moment, I realized the load had also started giving wildly inaccurate voltage readings.
Then I remembered that I'd pressed those buttons earlier and tried selecting something with the value-setting buttons. After that, it was just a matter of figuring it out.
So, about calibration. To the right of the value-setting buttons there are two more: the top one is for voltage, the bottom one for current.
I'll show you how to calibrate the current.
Connect an ammeter in series with the load.
1. Select CC mode and set a current, say 4.5 A (the higher, the better).
2. Press the lower-right button (next to the -0.01 button). A constant will appear on the screen, with a large value, for example 52435 or 65432. Use the value-setting buttons until the actual current matches the set value.
3. Switch back to CC mode and set a low current, say 0.5–1 A.
4. Press the same calibration button twice. A constant with a lower value will appear, for example 3452 or 4321. Use the same value-setting buttons until the actual current matches the set value.
5. Repeat until you get tired of it :) Each time, the readings at both the higher and lower current will get closer to the actual values—or rather, the actual values will get closer to the set ones.

Voltage calibration is roughly the same, but there are two ways to do it: the right way and the wrong way:
1. The wrong way: apply a regulated voltage and adjust the constants until the load's display shows the correct value. This method is very quick, but less accurate because the display has coarse resolution.
2. The right way: apply a voltage to the input with current limiting, for example from a power supply connected through a light bulb, though a power supply with current limiting is better.
Connect a voltmeter to the load terminals.
Switch the load to CV mode, apply some voltage to the input, say 20–60 V (the higher, the better), and set the voltage, for example, 5 V below the input voltage. The input voltage should now match the set value, since the electronic load is controlling it.
Press the upper-right calibration button (to the right of +0.01) to enter calibration mode, then use the value-setting buttons to adjust it until the external voltmeter shows the set value.
After that, switch back to CV mode, set, say, 5 V (2–5), and repeat the process with the second constant, as in the current calibration example.
I think the rest is clear: by making successive adjustments, you can get both the upper and lower values set accurately.



I didn't take many measurements specifically for the review, but at least one informative photo is still around.
On the left is an example of how it worked before calibration. You can see that the current reading was clearly too high. I was increasing it in 1 A increments, i.e. 0-1-2-3-4.
Besides setting the current incorrectly, the whole setup process took a long time—about 1 minute 40 seconds.
On the right is an example after calibration. I increased it to 5 A, 0-1-2-3-4-5, and the current was set accurately; the whole process took about one minute.


In addition to the basic parameters, you can measure (calculate) values such as mAh and Wh. There are three windows at the bottom showing the corresponding measurements. The timer keeps running as long as the load is switched on, regardless of the operating mode. I don't know how to reset these values, since the unit itself remembers them. I tried not only restarting the software but also launching a second copy of the program from another folder, so to reset them you have to disconnect and reconnect power to the load itself. Inconvenient.
But the Chinese wouldn't be the Chinese if they hadn't messed this up too.

Remembering how the USB tester worked, I decided to run a similar experiment here. I set the current to 4 A and started taking screenshots every 6 minutes, so the readings should have been 400 mAh, 4 Wh / 800 mAh, 8 Wh, and so on.
But it turned out that the mAh readings were exactly 10 times too low. I had actually noticed this earlier while experimenting, but decided to double-check.
How does that even happen?
It even reminded me of a passage from the book False Mirrors.

A little box sits in his palm. We crowd around, trying to make out what it is.
“Warlock-9300,” Shurka replies. “At last, it turned out just the way I planned…”
The box is a tiny elevator car. An ordinary one, brown, with sliding doors and a piece of cable sticking out at the top.
Except the elevator is ten centimeters tall.
“The most convenient shape,” says Maniac. “The ‘Nine-Thousander’ was supposed to work like that too, but it never came together…”
“Sasha… dear little Sasha,” Padla says hoarsely. “Are you sure you didn't get the size wrong? Huh?”
“I somehow didn't think about the size,” Maniac says self-critically, and I realize Padla is in for another round of punishment for that little joke.
“Looks like I misplaced the decimal point somewhere…”



Above, I mentioned that I had to ask for help with one thing from people whose native language is Chinese. The program has an option in the lower-right corner of its main window to record a log of its operation. This creates a CSV file in the program folder with values that are impossible to make sense of.


There are actually a lot of tools for working with the load, and that's partly why there won't be a follow-up showing the finished device. I have a feeling there's still more to come.
For example, there's supposedly a way to plot graphs -


As far as I can tell, the graphs are generated from data in another program. I downloaded it, and it even tries to work, though the output is nonsense, so here's a screenshot from the developer.


But an even bigger reason for putting the build on hold was that, while searching for information, I came across a module that can measure, display, and control the device.


The implementation is a bit odd, though. The module has its own current and voltage measurement circuits. On the left you can see the wires going to the current-sense resistor (a very proper four-terminal one), but the module is also connected to the RS-485 interface.
In addition to the basic features, this add-on is said to offer:
Optional Bluetooth control.
Load cutoff thresholds, such as minimum voltage or current, as well as a time limit.
Mode memory.
Compensation for voltage drop in the wires
Current up to 50 A
Coulomb counter
18-bit ADC.
Language selection - Chinese or English.

There is one downside, though: even on Taobao this module costs about 28 bucks :( But I may well splash out.


Another reason for considering this kind of control is the software glitches.
1. Random values occasionally flash on the screen. Fortunately, only briefly, and they don't get in the way.
2. The controls. Guys, this is ridiculous. I understand that this is a test version of the software, but this bad.....
Even when you're just selecting a current, voltage, or other value, changing each parameter takes about 3 seconds.
Say you need to set 1.2 A. It goes like this -
press 1,
wait 3 seconds,
press 0.1
wait 3 seconds
press 0.1
wait 3 seconds.

Now imagine how long it takes to set, say, 5.55 A....

But honestly, I haven't given up hope that they'll finish polishing the software. And I can also say that I have no real complaints about the loads themselves (the hardware): they work pretty well, and they're reasonably priced for both their features and build quality.
So here's my question: perhaps one of the programmers who also wants a device like this could help with the software. Maybe we could add an Arduino with a decent display, buttons, and an encoder. In that case, I can work on the hardware side by redrawing the schematic so others can build it, and we could put together a pretty good device.

For the high-power load, I'm taking my time looking for a good ammeter and voltmeter, as well as a multiturn potentiometer, an enclosure, and a power supply. But I may consider switching it to digital control. Either way, I have at least one more review planned, showing it in use.

That's probably all for now. I ordered the load through the agent yoybuy.com . This was my first time buying on Taobao. I can say I was completely satisfied with the agent's service: fast and efficient. Though now I owe them a little money :)
While I was at it, I worked out the total cost, and it came to - 31.27 + 23.49 (the items themselves) + 1.9 (shipping within China) + 5.67 (agent's fee) + 27.82 (shipping to me) - 10 (first-purchase bonus) = $80.15. I actually paid about 78.76, so I still owe 1.39.
The price was mostly high because the package was heavy, and the modules have also come down a bit in price since then.

As a bonus, here's the story of my purchase, along with instructions on how to buy through yoybuy.com. It's a bit spontaneous in places, but this is the best I could do.
First, of course, register on yoybuy.com. You can just follow the direct link, or use mine. It won't cost you anything, and I might get a point for putting together the guide :)
Along the way, you'll see a list of stores you can order from.





After I received the parcels, one of my readers sent me a link to the same products on AliExpress. The total for the same set there comes to $93, about $13 more than I paid a month ago. But even if the price had been the same, I still gained a little experience buying from Taobao, and that's worthwhile in itself :)
High-power version
150 W version.

That's definitely everything now. As always, I'm looking forward to your comments, advice, questions, and feedback :)
$22.49+29.93 (без учета накладных расходов)
Go to store
This page was found when searching for:
9, 6, 2, 4, нагрузка кт825, активеая нагрузка mysku, купить набор электронной нагрузки, xhdz-fz-2e, электронная нагрузка 150w 100v 10a, электронная нагрузка на кт825 своими руками схема, электронной нагрузка до 480w форму, тест обзоры электронных нагрузок, diy kit электронная нагрузка 4 точечное подключение, et5410 компенсация, электронная нагрузка с алиэкспресс просаживается напряжение, электронная нагрузка с алиэкспресс, обзор активных нагрузок с алиэкспресса, электронная нагрузка 60 вт. версия 3, электронная нагрузка et 5410 обзор, шим электронная нагрузка kitaj, xhdz fz 2g схема, xhdz-fz-2g схема, нагрузка 60 ватт доработка, настройка электронной нагрузки из китая, https://www.kirich.blog/obzory/radiolyubitelskoe/480-para-elektronnyh-nagruzok-ili-moy-opyt-pokupki-s-taobao

Questions and answers

What are the stated specifications of the 300 W electronic load?

The selected model is rated for up to 300 W, 150 V and 40 A, with CCCV modes.

How is the 300 W electronic load built?

It consists of two connected modules and is cooled by two fans and an aluminum heatsink. Four IRFP460A transistors serve as the load.

What did the author learn from buying electronic loads on Taobao?

The purchase through the yoybuy.com agent went smoothly, but shipping the heavy parcel worked out to about $22 per kilogram. The author also describes paying for shipping and tracking the parcel.

The figures from this review are in the measurement database: Electronic loads


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments16

Comments are published in their original language.

  1. Leon
    5 November 2017 22:13#1
    Также есть место под разъем 74HC. Вообще это обычно обозначение серии логических микросхем, но что в данном случае, я не знаю. Один контакт идет на землю, четыре - к микроконтроллеру.
    Возможно экран, подключенный через 74HCxxx
    -1
    1. 6 November 2017 00:40#2
      Очень маловероятно.
      0
  2. 11 November 2017 22:42#3
    Хорошая нагрузка! Жаль, что ПО подводит пока.
    0
    1. 11 November 2017 22:59#4
      Да, на видео наглядно видно, насколько оно глючное.
      Но больше даже не глючное, с этим еще можно смириться, скорее неудобное. Очень надеюсь что будет новая версия.
      0
      1. 12 November 2017 00:24#5
        Очень надеюсь, что будет новая версия электронной нагрузки от Kirich )))
        +1
        1. 14 November 2017 16:57#6
          Да я тоже надеюсь на это, но вообще все потихоньку думаю над своим вариантом, с мощностью 800-1200 Ватт.
          +1
  3. Даниил
    20 December 2017 18:47#7
    SWIM - интерфейс для прошивки контроллеров STM, у контроллера соответствующая нога также обозначается
    0
    1. 23 December 2017 03:39#8
      Спасибо, тоже встречал эту информацию. Получается, что смысла осоого в данном случае он не имеет, жаль :(
      0
  4. 18 March 2018 17:27#9
    А не пробовали покупать на Taobao самостоятельно? Может без посредника получится дешевле. Нужно только подобрать склад в Китае.
    0
    1. 19 March 2018 13:49#10
      Возможно, надо будет попробовать. Мне по сути Юбей удобен тем, что там принимают вебмани.

      +1
  5. 19 March 2018 14:12#11
    Я платил на Taobao с карты ВТБ Visa. Складом пользовался Youcanbuy.
    0
    1. 19 March 2018 14:43#12
      У меня нет карт, потому я ползуюсь вемани :)
      0
  6. Дмитрий
    18 December 2018 23:39#13
    Доброго.И какую из этих двух нагрузок посоветуете приобрести?подумываю себе собрать в лабораторию,а вот что ещё не определился.
    0
    1. 19 December 2018 01:49#14
      Ту, которая с резистором, а не с цифровым управлением
      0
  7. 1 January 2020 15:25#15
    hei!
    подключил первый вариант SOUSIM к modbus analyser (там serial ttl). ничего информативного сходу не увидел, а данных из него сыплется валом.
    Можно выложить куда-нибудь весть этот комплект софта (я не смог его найти на baidu, да и скачивать оттуда целая эпопея).
    Спасибо!

    0
    1. 2 January 2020 12:16#16
      Странно, вроде выкладывал как-то ссылку.
      А, все, понял. Там какая-то проблема с гугл диском была, он не хочет давать другим файл на скачивание, напишите мне на почту, скину архив, он небольшой.
      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister