/       /       /    JGNE 26650 LiFePO4 Batteries with 2300, 3000 and 3600 mAh Capacities
Support the project on Patreon


JGNE 26650 LiFePO4 Batteries with 2300, 3000 and 3600 mAh Capacities

3.25-3.75€ (без учета доставки)
Go to store
Continuing my look at JGNE batteries, this time I’m testing three larger LiFePO4 models with capacities of 2300, 3000 and 3600 mAh. They differ not only in capacity, but also in maximum discharge current.


While doing some more searching, I found what I assume is the JGNE manufacturer's website - link. In any case, this review will include datasheets for Enerpower batteries, since my investigation showed that they are actually one and the same. But I'm getting ahead of myself.

So, today I'm reviewing three batteries. They're all the same size, all LiFePO4, and apparently made by the same company, but they differ in both capacity and maximum discharge current. They also came in the same package, so I decided to cover all three in one review.


JGNE 26650 2300 mAh - 46 A.
A high-current model, priced at €3.75. There's a small discount for buying in quantity, but I didn't think it was significant - product link.


The product page lists the following specifications:
Chemistry: LiFePO4
Type: 26650
UL: MH48108
Name: HTCFR26650-2300mAh-3.2V
Nominal voltage: 3.2 V
Maximum charging current: 11.5 A
Capacity: 2300 mAh
Continuous discharge (in amps): 20C (approximately 46 A)
Internal resistance: <12 mΩ
Pulse load: 70 A / 10 seconds
Weight: 85 grams
Dimensions: diameter 26.15 mm / length 65.60 mm
Protection circuit: NO
Service life: 2000 full cycles (100% DOD) / 4000 full cycles (80% DOD) / 6000 full cycles (60% DOD)

Datasheet from Enerpower, with specifications that match those listed above.


Compared with the 18650 batteries shown earlier, these look different only in size and, of course, the markings :)
The production date is around early October 2019.



The manufacturer recommends charging the batteries at 0.5C. I decided to go against that and charge them at 1C, since these are high-current batteries and, in my opinion, the datasheet was simply made “from a template.”


At a 1C charging current, after discharging at 0.5C, charging took just over an hour.


Fast charging at 11.5 A is also claimed to be possible; in this mode, the battery can be charged in 15 minutes.


As before, I ran a conditioning cycle at 0.5C. Below are the results for the “zero” cycle (blue) and the measurement cycle (actually the third). All the batteries (both these and the higher-capacity ones) initially had a charge of around 75–80%.


The manufacturer provides test results at currents of 0.5, 5, 10, 15, 20, and even 30C, corresponding to currents of 1.15, 11.5, 23, 33.5, 46, and 69 A. Unfortunately, I can only test at currents up to 40 A.


I ran 8 tests at currents of 0.2, 0.5, 1, and 2C, and 10, 20, 30, and 40 A.
Based on the graphs, we can say that the curves are indeed quite good up to and including 20 A. At 30 and 40 A, there is a noticeable voltage drop.


Temperature at 20, 30, and 40 A.
Looking at the temperature, the battery handles 40 A without any problems. I think it would also work fine at higher currents, mainly because its low capacity means it simply won't have time to overheat.


The second sample



For high-current battery models, I run an additional test to see how much capacity they deliver after being discharged at the maximum current and allowed to cool completely. The lower this figure, the more efficiently the battery performs.
In this case, I got 91 mAh, or about 4%, which is pretty good.


The batteries showed fairly good consistency in their characteristics, with differences within the instruments' measurement error.


Internal resistance before testing, after “normalization,” and at the end. Looks good to me.


The datasheet also included data on battery performance at different temperatures and service life.



JGNE 26650 3000mah - 30A
A noticeably higher-capacity model, priced at €3.45, with small wholesale discounts available — product link.

The store's picture shows an Enerpower, not a JGNE, which again suggests that these are the same cells.


Specifications from the store page
Chemistry: LiFePo4
Type: 26650
UL: MH48108
Name: HTCFR26650-3000mAh-3.2V
Nominal voltage: 3.2 V
Cutoff discharge voltage: 2.5 V
Cutoff load voltage: 3.6 V
Maximum charging current: 9 A
Capacity: 3000 mAh
Continuous discharge (in amps): 10C (about 30 A)
Internal resistance: <15 mΩ
Pulse load: 45 A / 5 seconds
Weight: 85 grams
Dimensions: diameter 26.15 mm / length 65.60 mm
Protection circuit: NO
Service life: 2000 full cycles (100% DOD) / 4000 full cycles (80% DOD) / 6000 full cycles (60% DOD)

Back to the Enerpower website, where we find the corresponding datasheet
As far as I can tell, there's an error in the Capacity range column of the table: a range of 3300–3500 doesn't make sense when the nominal capacity is 3000. Most likely, the datasheet was copied from the manufacturer's 3400 mAh batteries, and this field wasn't updated.


The production date is the same as for the 2300 mAh model: week 39 of 2019, or early October.



The manufacturer specifies a charging current of 0.5C, or 1.5 A. In my tests, I used a charging current of 1C, or 3 A.


At 1C, after a preliminary discharge at 0.5C, charging took one hour.


As with the previous model, these batteries can also be charged faster, though in this case at 9 A. Charging then takes about 25 minutes.


The preliminary (blue) and main (red) discharge cycles at 0.5C.


I found data for different discharge rates—1, 2, 3, 5, and 10C—but in my opinion, at 10C (30 A) they are somewhat... strange.


In my case, the tests were expanded a little, since the battery was tested at 0.2, 0.5, 1, 2C and 10, 15, 20, and 30 A.
Judging by the graph, the battery works normally up to 20 A; above that, there is a noticeable voltage drop.


Temperatures at 15, 20, and 30 A—nothing unusual, all within the normal range.


The second sample performed slightly better, but the difference is very small.



As before, data on capacity versus temperature is provided. It shows that using the battery below -10 is inefficient, since its capacity drops by a third.
Data is also provided on service life at a discharge rate of 3C (9 A).


Comparison of the two batteries at 0.2C, 2C, 15, and 30 A.


Resistance before testing, after the "zero" cycle, and at the end.


As before, data on capacity versus temperature is provided. It shows that using the battery below -10 is inefficient, since its capacity drops by a third.
Data is also provided on service life at a discharge rate of 3C (9 A).



JGNE 26650 3600mah - 10.2A
A high-capacity model, priced at €3.25 each, product link.


Specifications from the store page
Chemistry: LiFePo4
Type: 26650
UL: MH48108
Name: HTCFR26650-3600mAh-3.2V
Nominal voltage: 3.2 V
End-of-discharge voltage: 2.5 V
End-of-charge voltage: 3.6 V
Maximum charging current: 3.4 A
Capacity: 3600 mAh
Continuous discharge (in amps): about 10.2 A
Internal resistance: <30 mΩ
Pulse load: 10.2 A / 5 seconds
Weight: 87 grams
Dimensions: diameter 26.15 mm / length 65.60 mm
Protection circuit: NO
Service life: 2000 full cycles (100% DOD) / 4000 full cycles (80% DOD) / 6000 full cycles (60% DOD)

I ran into a small snag finding the datasheet: Enerpower's website doesn't list any 26650 batteries with this capacity, only 3400 and 3800 mAh models.
I had to search a little longer and came across the goldencellbattery website, where I found at least some fairly detailed information, including graphs. I also found a similar description there for the LiFePO4 18650 1800mAh batteries from the previous review. As far as I can tell, it matches the Enerpower datasheet, although the photos don't show any markings at all.


The production date is mid-January 2020, matching the date on the 1800 mAh batteries from the previous review. As it turned out, of the five battery types I had, one had no date, while the others had dates from only two batches: early October 2019 and mid-January 2020.


Also, during inspection I found that the 26650 cells have different contact shapes: 2300 mAh on the left, and 3000 and 3600 mAh in the middle and on the right.


The dimensions and weight all match the stated specifications.


The recommended charging current here is also 0.5C, and in this case I completely agree with the manufacturer, since high-capacity batteries don't like high charging currents.


A full charge took 2 hours and 7 minutes after discharging at 0.5C.


Zero (blue) and measurement (red) cycles for both batteries.


The manufacturer provides capacity data for discharge rates of 0.1, 0.2, 0.5, 1, 2, and 3C. After testing quite a large number of batteries, the only ones I've seen tested at 0.1C were Enerpower (JGNE) batteries, which is very unusual. Of course, you could say that this used to be standard practice, but that was a long time ago and not for lithium batteries, which is exactly why it seems unusual.


Tests were conducted at 0.2, 0.5, 1, 2, and 3C, and at 15 and 20 A. Note that 10.8 A is the maximum current for these batteries. I tested them at 15 and 20 A just out of curiosity, since they performed normally at the rated 10.8 A.

You could say the batteries handle 10.8 A (3C) very well. They also handled 15/20 A, but with a noticeable voltage drop and, consequently, less energy delivered in Wh.


Temperature at currents of 10.8, 15, and 20 A.
Even when overloaded to almost twice their rated current, the batteries only heated up to 76 degrees, which is quite good. At the rated maximum current, the temperature was only about 50 degrees.


The second sample showed the same results.



The results from the two samples were also very consistent, with only a tiny difference. Below is a comparison at 0.2C, 2C, 15, and 20 A.


The internal resistance here is noticeably higher than in the previous batteries, but these are high-capacity cells. The results are shown before testing, after the “zero” cycle, and at the end.


On the same page of the goldencellbattery website, I found graphs showing capacity versus temperature and battery aging at a current of 1C (3.6 A).
You can see that capacity has already dropped by about 20% at 0 degrees, so using these batteries at lower temperatures is inefficient.



Conclusions.
Based on the test results, I can say the following:
All the batteries met the values specified by the manufacturer. However, although the 2300 and 3000 mAh models deliver their rated currents of 40 and 30 A, respectively, they have a noticeable voltage drop to around 2.8–2.9 V. The only model that avoids this voltage drop and, as testing showed, works normally even at 1.5 times its rated current is the 3600 mAh model.

Of course, each battery is intended for a particular application, but in terms of capacity/performance/price, I liked the 3600 mAh ones. The 2300 mAh model also turned out to be pretty good, since it didn't get too hot even at 40 A.

That's all for today. As always, I hope you found this useful.
3.25-3.75€ (без учета доставки)
Go to store
This page was found when searching for:
ifr-26650-4s1p, mz26650 как зарядить mc 3000, производитель ячеек jgne, максимальная емкость аккумулятора 26650, внутреннее сопротивление аккумулятора 26650 125mr, аккумулятор lfp 26650 3.2 вольта как заряжать, аккумулятор 26650 максимальная емкость, antbatt lifepo4 26650 mp, ячейки 26650 высокотоковые, 26650 аккумулятор высокотоковый ток разряда 40 а, описание аккумулятора 26650 3,2 м, 26650 lifepo4 характеристики, 26650 аккумулятор 3.2в, сколько весит аккумулятор 26650 в граммах, аккумуляторы 26650 характеристики, батарейки 26650 аккумулятор характеристики, даташит аккумулятора 26650, акб 26650 характеристики, характеристики 26650 аккумулятор, опту 26650 3600mah datasheet, 26650 аккумулятор характеристики, 26650 аккумулятор размеры, lifepo 26650 как варить аккумуляторы, jgne lifepo4

Questions and answers

What discharge currents did the JGNE 26650 2,300, 3,000 and 3,600 mAh batteries handle?

Their stated maximum currents are 46, 30 and 10.8 A, respectively. In testing, the 2,300 and 3,000 mAh models showed noticeable voltage sag at 40 and 30 A; the 3,600 mAh model worked normally at 10.8 A and handled a higher load with voltage sag.

Which tested JGNE 26650 battery performed best?

The author preferred the 3,600 mAh model: it showed no noticeable voltage sag at its rated current and worked well even under a 1.5-times overload. The 2,300 mAh model also performed well, including at 40 A.

How do JGNE 26650 batteries perform at low temperatures?

According to the data cited, the 3,000 mAh model loses about a third of its capacity below −10 °C. The 3,600 mAh model loses about 20% at 0 °C.

The figures from this review are in the measurement database: Batteries

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments1

Comments are published in their original language.

  1. 23 December 2022 02:03#1
    Здравствуйте!
    Что можете сказать спустя время про аккумуляторы JGNE 26650 3600mah ?
    Подумываю собрать из них сборку 4s8p или 4s10p, пользоваться при отключениях электричества.
    Стоит их рассматривать к покупке или посоветуете какие-то другие варианты по нормальной цене?
    0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister