/       /       /    Reolink C1 Pro mains-powered pan-and-tilt camera with 2560x1440 resolution
Support the project on Patreon


Reolink C1 Pro mains-powered pan-and-tilt camera with 2560x1440 resolution

$79.89 ($67.99)
Go to store
Some time ago, I posted a review of an inexpensive Escam pan-and-tilt camera. Today’s review is also about a pan-and-tilt camera, but a higher-end model. To get straight to the point, I’d say the main differences are at least two: resolution and build quality. In fact, there are more differences
For those who want the details, this review includes an inspection, a look at the software, some tests, and, of course, a teardown “down to the last screw.”




First, here are the main technical specifications:
Hardware
Image Sensor 1/3" CMOS Sensor
Resolution 2560 x 1440 (4.0 Megapixels)
Lens f=4.0mm Fixed, F=2.0, with IR-Cut
Viewing Angle Horizontal: 80° Vertical: 42°
Pan/Tilt Range Horizontal: 355° Vertical: 105°
Minimum Illumination 0 Lux (with IR Illuminator)
IR Range 10-12 m
Power 5.0V/2A, <6W
Connectors One 10M/100Mbps RJ45, microUSB (power), microSD slot
Wireless Standard IEEE 802.11a/b/g/n
Operating Frequency 2.4GHz / 5GHz
Built-in microphone and speaker

Software
Protocols & Standards HTTPS, SSL, TCP/IP, UDP, UPNP, RTSP, SMTP, NTP, DHCP, DNS, DDNS, FTP, ONVIF, P2P
Image Compression H.264
Maximal Frame Rate PAL: 25fps, NTSC: 30fps
Code rate 1024Kbps ~ 8192Kbps
Audio Two-way Audio
Maximal User Access 20 Users
Browser Supported IE, Edge, Chrome, Firefox, Safari
OS Supported PC: Windows; Mac OS; Smart Phone: iOS, Android
Record Mode Motion Record/Schedule Record (default: Motion Record)
Wireless Security WPA-PSK/WPA2-PSK

Additional specifications
Operating Temperature : -10~+55
Dimensions 103х 95 х 117mm
Weight 300g

To be fair, I actually wanted a different camera, one that was more interesting to me, but this is the one they sent.
The camera comes in a fairly large box, with a small sticker on the side listing the main specifications. I have one minor quibble at this point. The listed resolution is 2560 x 1440 (4.0 Megapixels), but to be fair, 2560 x 1440 is not 4 megapixels, but only 3.7. They rounded up. For example, Hikvision’s model, advertised as 4 MP, has a resolution of 2688 x 1520 = 4.08 MP.


Inside the box, I found another box with accessories, a bag with the documentation, and the camera itself in a large protective package.


Besides the manual, the package includes a CD with software, a sticker warning that video surveillance is in progress, and a mounting template sticker.
The cables, power supply, and everything else are packed tightly inside the little box.


“Everything else” means:
1. Power supply
2. Bracket
3. Mounting hardware
4. Ethernet patch cable
5. USB-to-microUSB cable


1. USB cable, about three meters long, quite thick and substantial. This is the first time I’ve received a device with a cable like this included. Nice.
2. Patch cable for connecting to a local network. Since Ethernet wall jacks aren’t very common in our apartments, and the cable itself is about a meter long, it’s not very useful in this case.
3. 5 V, 2 A power supply. No complaints; it works great.


The package also includes a bracket for mounting the camera on a wall or ceiling, mounting hardware, and a paper clip for accessing the reset button.


As I said, the camera’s packaging gets top marks. It would be very difficult to damage it in transit.


When I first saw this camera, it reminded me of a cross between a matryoshka doll and a robot :)
I’d put it in the “nice to hold” category. It doesn’t give you that feeling that you’re holding something cheap—not inexpensive, but shoddy.


Views from all four sides. The only thing worth noting is that there are two grilles on the sides. The speaker is behind just one of them; the other is purely decorative.


There’s a fairly significant feature that I didn’t understand at first. At the very beginning of testing, I turned the camera on and everything was fine. Then I panned it back and forth, and at some point the image flipped 180 degrees. I thought, “That’s it, a software glitch,” especially since I’d been poking around in various settings.
It turned out that the camera can look behind itself not only by panning horizontally, but also by tilting vertically. In other words, the tilt range is quite large. In the photo, the camera is facing forward horizontally, but backward vertically. The image doesn't flip automatically, which is what confused me.
The manual says the vertical rotation angle is 105 degrees, but in reality it's at least 170.


The horizontal rotation angle is slightly less than specified: about 350 degrees versus the stated 355. The photo shows the camera in its two extreme positions.


The lens looks very much like the one on the Escam pan-and-tilt camera. I remember trying to adjust it on that one. There were no problems with it here—or, more precisely, there was no need to adjust anything.
An IR illuminator is installed around the lens, under the trim, and the light sensor is visible above it.


There's a status indicator at the bottom of the front, though at first I thought it was a button :)
Blue on the left, red on the right. The blue light is always on; the red one indicates activity during startup/connection.
It's dim, so it won't draw attention.


The connectors and memory card slot are on the back of the housing.


I also noticed a couple of issues. There's a decorative ridge in the housing above the connectors that gets in the way when unplugging the Ethernet cable, since it overhangs the clip you need to press.
The memory card slot is awkward too: the spring is quite strong, and the card sits deep inside. Once, when I was inserting it, the memory card nearly flew out the window—luckily, the camera was turned slightly to one side. So, that's a minus.


There are rubber feet on the bottom, as well as a threaded hole for mounting the camera on a bracket. In this case, I used it to mount the camera on a tripod. The hole isn't very deep, about 6 mm, and you can also see the unprotected circuit board inside. That led to a separate story.

Right at the start of my experiments, I ran into an unusual problem. At first, I blamed the shallow hole.
I powered it up on my desk from a USB hub. Everything was fine; it connected to WiFi, and I checked it.
I moved it somewhere else, powered it from a different power supply, checked it, and it was fine.
Next, I needed to install the camera on the balcony, and I had a perfectly decent 5 V, 1 A power supply lying around.
I took it to the balcony, put it on the tripod, and switched it on. The camera turned around, moved into position, and that was it—it was no longer on the network.
I thought that was it: maybe I'd cut through the traces with the tripod screw when mounting it. I took it off the tripod, brought it to my desk, powered it from the hub, and it worked.
I took it back to the balcony and mounted it on the tripod. WiFi didn't work, but everything was fine when I connected it by cable.
I took it off again and carefully inspected the board through the hole. Everything looked fine.

It turned out that when the camera has power problems, its WiFi drops out. It works perfectly with the supplied power supply. But it did make me nervous while I was figuring it out.


To avoid interrupting the flow, I'll show you how I took the camera apart now, although I did that after all the tests. I'll say right away that it still worked after I put it back together :)
There are seven self-tapping screws on the bottom. I first removed three, but nothing changed, so I just removed all of them.
The bottom is aluminum, surprisingly, not plastic. By the way, the bottom of the camera gets noticeably warm during operation.


Once I'd removed the lower section, it was clear that three screws hold the bottom panel in place, but you can only remove it completely by undoing all seven.
The four larger screws hold the lower part of the camera housing together with the bottom panel. If I hadn't needed to remove the panel, I could have undone just those four.




My first impression of the board was that it looked pretty good, but there was a strange white residue. The WiFi module is visible at the top; there's also room for a similar module at the bottom, but in a simpler configuration with a single antenna.


The specifications and advertising both claimed dual-band WiFi and support for 2T2R MIMO.
The module is based on the Atheros Ar1021X and does indeed support all the advertised modes. I can also say that, in setup mode, the camera not only detected my router through several reinforced-concrete walls and from a distance of about 12 m, but connected to it on both bands and worked. The only problem was that the connection speed left a lot to be desired: it started lagging, and I had to lower the video recording bitrate.
Overall, though, I can say that the WiFi is a pleasant surprise and should work reliably under more normal conditions. The camera also spent several days recording continuously over WiFi and worked perfectly.


There is also a motor driver IC on the underside, along with a UART connector and flash memory for storing the camera firmware.


Now let's see what's under the board, although it's already clear that it's just a tangle of wires.


My hunch was right: the underside is a complete mess. As they say, "you'd need a bottle to make sense of it."
Most of the wires are twisted together, and they're fairly flexible, too.


There are far more components on this side of the board, not to mention the number of connectors. During disassembly, I unplugged almost all of them, but decided to leave the larger ones in place because they were so tight. In fact, I did break one of the small connectors and had to repair it.


This side also has 256 MB of Samsung RAM, an Ethernet chip, a real-time clock with a battery, and a whole bunch of voltage regulators.
A battery for the internal clock may seem like a small detail, but it raises the camera's overall standing a little after the microUSB connector had lowered it.
Let me explain. Any halfway decent digital surveillance camera has an onboard battery to power its clock, because synchronization isn't always possible. But all surveillance systems are designed around 12 V DC or 24 V AC power, or, more commonly these days, 48 V PoE.
5 V power is for webcams and systems that have little to do with proper video surveillance, since a camera like this needs either a power supply installed next to it or a converter from the standard 12 V supply.
So, having a battery is a plus; being able to power it only from 5 V is a minus. The only advantage of 5 V power is that it's convenient to use a power bank.


The SoC has a heatsink on it, covered with foil on top. This is to protect the wires from the heatsink's sharp edges. It's a thoughtful touch, though a bit makeshift; a plastic frame would have looked much better.


The heatsink was glued on with something silicone-like and was difficult to pry off. But curiosity got the better of me, especially since this can sometimes help determine whether the claimed resolution is even possible.
The SoC used is a GM8138SF-BA made by Grain Media.




And this is where things get a little strange, especially considering that by the time I took the camera apart, I already knew it produced pretty good footage.
The specs say the camera's codec supports up to 1080p at 45 fps. But the actual video looks noticeably better than 1920×1080, and its resolution does match the stated specs.


The gears for horizontal rotation are just visible between the housing halves: one large and one small.


They're driven by a small motor, with the indicator board located next to it. Motor connection: four-wire.
During testing, I noticed that while horizontal panning is excellent and the camera moves very smoothly, vertical movement has a few small jerks.


We remove four more screws and take off the top section, which itself consists of two halves held together by clips and adhesive tape stuck underneath.
The tape has grease on it to protect the wires from chafing—a thoughtful touch, no complaints there.


Once the top section is separated, the camera practically falls apart into its component pieces. Separating the whole assembly in the first place was quite difficult, and putting it back together afterward was even harder.


The camera module contains a board with the image sensor and a geared motor for vertical panning.


The IR LED board has an aluminum base to improve LED cooling. Oddly, there are only eight LEDs, even though there is room for four more; jumper wires are soldered in their place.


It took some effort, but I finally got to the image sensor board. Wires kept getting in the way the whole time.


The only active components here, essentially, are the image sensor itself and the driver for the IR-cut filter shutter.
There are also a few small components near the connector, most likely voltage regulators.


And here is the final destination of my teardown: the image sensor with the lens. The board kept trying to slip away, so I had to hold it with tweezers :)


The specifications say the image sensor is 1/3 inch. Its actual size is about 6x3 mm, which roughly matches the stated figure. In any case, during testing the camera performed quite well in low light, so it was already clear that the sensor wasn't 1.4 inches.
Some dust got onto the sensor during disassembly, so I had to clean it too.

By the way, you can see the threads left by the screws in the lens mounting holes. On the previous cameras, the screws had some play; here they fit perfectly, so the lens is very unlikely to shift after disassembly.


Final photo: the camera is completely disassembled.
Well, not quite—I didn't take apart the gearbox, but otherwise that's pretty much everything :)


The description claimed support for various browsers, which is good, but first I need to find the camera's address so I can connect to it from a browser.
I open my router's menu and check which address it assigned via DHCP. In this case, it's 100.127


I launch my old Opera 12, enter the address, and the camera prompts me for a username and password.


Unfortunately, I ended up getting an error.


I do the same thing in Chrome. It works much better here; the browser only asks whether I want to enable Flash support.
Cameras usually ask you to install ActiveX, but that wasn't the case here, which is great.


A few seconds later, I see the camera feed on the screen.
At the bottom of the main window is a button for selecting the stream: main, secondary, or balanced (automatic, depending on network conditions). There is also a volume control for the camera's microphone on the right.
One nice bonus is that you can select the stream even on the login screen, which can be useful when the connection is poor.


On the right is a menu for adjusting the main settings. Interestingly, Opera had an option to adjust the panning speed, but this one doesn't. In any case, the speed is always the same, unfortunately.


The camera's web interface has a lot of settings, though personally, I still find a few things missing.
Settings for the OSD display mode and its position.


Video encoding settings. Two modes are supported: main and secondary. Mostly, the camera supports resolutions up to the maximum advertised, at 25 fps (even at the maximum resolution), with a bitrate of 1 to 8 Mbps.
The camera doesn't choke, even at the maximum settings.


There are a lot of settings, so I'll hide the rest under a spoiler. I think that's for the best.


Besides the web interface, there's also video surveillance and recording software. I didn't bother digging out a CD drive and simply downloaded it from the manufacturer's website.
The software installed without any problems and automatically found the camera. The whole process went like this: connect the camera to the local network, install the software, launch it, and watch the video. I think that's excellent, especially for users who aren't very tech-savvy.



There's no freely resizable window mode, but you can choose the size of the program window. This is common practice in video surveillance software, though the implementation here is a little different from the usual approach.


Windows software



If you insert the flash drive into a computer, you'll see a directory structure like this. The camera records the main and substreams separately, along with an index file.
This is quite handy when viewing footage over a slow internet connection.
When recording with the computer software, it only records the main stream (I'm not entirely sure about this), and there's no index file, so it seems to record for no reason.
In both cases, the video is split into 5-minute segments. The screenshot shows recording with motion detection disabled and the maximum bitrate on both channels. At that rate, one hour of main-channel footage takes about 3.6 GB, while the substream takes 240 MB. Naturally, enabling motion detection and reducing the bitrate to 2–4 Mbps will bring the file size down considerably.


The recorded video files are arranged as follows:
1, 2, 3 — main channel: day, day, night.
4, 5, 6 — substream: day, day, night.


There's also an Android app, which I downloaded from their website.

Android app


And finally, a few tests.
Daytime footage. It was overcast, so the brightness is somewhat reduced.


Video comparison with and without image processing.
1. Original
2. BLC mode enabled (backlight compensation)
3. Wide dynamic range enabled.


Although the camera is essentially an advanced version of a “video baby monitor,” it offers plenty of image adjustment and processing options.
1. Basic image
2. Color mode in the evening
3. IR illumination disabled. A useful feature that few Chinese cameras offer.
4. BLC mode (50%)
5. DNR (wide dynamic range)
6. RD-NR function (noise reduction) off, DNR off
7. RD-NR off, DNR on.
8. DNR on and set to maximum.
9. Original settings, but with outdoor mode enabled.

Of course, the outdoor lights were on in every shot, but the camera isn't marketed as an outdoor model, so its illumination probably wouldn't be useful in these conditions anyway. Still, I should point out that the camera holds a normal color image for quite a long time, even though the street already looks pretty dark to the naked eye.


The back of the house, while there were still plenty of leaves :) A pretty tough scene for the camera, with lots of small objects.


Room, standard mode.


BLC enabled


Same sequence, but in complete darkness.




This test gives a better idea of the actual resolution. The camera is about 2.5 m from the wall.


Image corners. The geometry is clearly off, but there don't seem to be any particular problems with lens alignment.


Now this is a much more interesting test, which in my opinion tells us more than many of the previous ones.
A comparison of image sharpness, and therefore resolution (albeit indirectly). For all tests like this, I always position the cameras so they capture the same section of the wall, then crop a portion of the image. This way, the test image always takes up the same area of the frame.

In terms of sharpness, it's slightly better than the Hikvision with its 3.2 MP resolution, and noticeably better than the Escam 4 MP. At the very beginning, I wrote that the sensor's actual resolution is not 4 MP, but only 3.7 MP. Compared with the 3.2 MP Hikvision, that seems quite believable; the image is worse because of the lower-quality lens.
In any case, it's definitely better than 1920x1080, which settles the question of whether the resolution is higher than FullHD, as I mentioned when discussing the processor used in the camera.


Although the camera has many features borrowed from its more advanced “colleagues,” the lack of an option to automatically invert the OSD text color was a real disappointment. When installing it at home, you have to find a spot for it so you don't end up with this.
By the way, these photos show the same view, but the bottom one has BLC enabled, so it doesn't always help.


As promised, here's a link to a video sample. I couldn't cut it without re-encoding, so I just uploaded a clip “as is.” From about halfway through, you can hear people talking about 20 m from the camera. In my opinion, that's excellent. The camera also picks up what's happening inside the apartment just fine, which is why I give the audio a solid 5. For the video, it's better to judge for yourself. Just keep in mind that when viewing it on monitors with a FullHD resolution or lower, the image will look worse than it does in reality.
Google Drive, Yandex Disk.


After spending quite a while playing around with the camera, I can say that it has more advantages than drawbacks.
Its advantages include fairly high build quality and a good set of accessories, a reliable WiFi connection with support for two bands, and decent image quality, especially in the dark. The audio is excellent, and it can tilt up to 170 degrees vertically. The software is reasonably well thought out and offers a ton of settings. I was pleased with both the decent included power supply and the long cable and bracket.
Unfortunately, there are drawbacks too: the image is quite dark, so you need to adjust the brightness. The camera is picky about the quality of its power supply. But what surprised me most was that there was no way to play back video recorded on a computer using the camera's own software. Maybe it's some kind of tricky bug; I won't argue the point.

In my opinion, the camera falls somewhere in the middle. It doesn't measure up to proper video surveillance systems, although it has plenty of options and settings, but it has clearly outgrown its counterparts in the “baby monitor” category. I'd be more inclined to classify it as a surveillance camera, if it weren't for the microUSB power input and lack of PoE.

Now for the price. Yes, $80 is a bit steep. That's basically what a full-fledged 4 MP Hikvision camera costs, though that one isn't a pan-tilt model. Here, for the same money, we get slightly worse image quality (there's no getting around that), fewer software features (for example, no ROI), probably no full-fledged support, but we do get pan and tilt, a microphone and speaker, dual-band Wi-Fi, a power supply, and a cable.

Before the review was published, the manager told me they were planning to drop the price to $67.99 for 11.11, which is much more appealing than the current $80. I didn't track the price before, but about a month to a month and a half ago it was also $80.

There are also $5 off $50 and $5 off $20 coupons on the seller's page, though I don't know whether they apply to this item. If they do, the final price could be pretty good.

That's all for now. As always, I'll be glad to answer questions, read your comments, or just chat.
$79.89 ($67.99)
Go to store
This page was found when searching for:
обзор reolink, https://www.kirich.blog/obzory/kamery/485-setevaya-povorotnaya-kamera-reolink-c1-pro-s-razresheniem-2560h1440, регистратор для камер reolink, reolink 1c pro, настройка reolink e1 outdoor, reolink e1 outdoor отзывы, reolink c1 pro poe, реолинк тест обзор, reolink e1 pro подключение к usb, камера reolink e1 pro работает ли без интернета, reolink e1 pro автономная настройка питания, reolink е1 pro питание от повербанка, 4pda reolink c1, reolink c1 как прошить, камера реолинк с1 про пароль по умолчанию, камеры видеонаблюдения reolink отзывы, reolink c1 pro firmware, reolink e1 pro сохраняет видео в низком качестве, reolink c1 pro прошивка, видеокамера reolink c1 pro, reolink c2 pro отзывы, может ли камера реолинк передавать звук, reolink sravnit misecu, reolink c1 pro 4pda, reolink разборка

Questions and answers

What is the pan range of the Reolink C1 Pro?

The author measured about 350° horizontally, compared with the stated 355°. Vertically, it turns at least 170°, although the manual specifies 105°.

What power supply does the Reolink C1 Pro need?

It is rated for 5 V/2 A and is sensitive to power-supply quality. The author encountered problems with a 5 V/1 A supply.

What drawbacks did the author find with the Reolink C1 Pro?

The image looked rather dark and needed brightness adjustment. The author also could not play back video recorded to a computer using the camera’s own software.


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister