Powerful Dual-Channel DC-DC Converter
Taobao often has sellers who dismantle all kinds of used equipment and sell the parts separately. In this case, I happened to find just such a seller. Judging by the comments, he has regular customers who are quite happy with his products, which was partly what prompted me to order several converters instead of just one. After the first tests, it was clear that I’d made the right call, especially since by the time my package arrived, he had already sold them all. I think these converters may turn up elsewhere, too; the reason should become clear from the review.
So, I ordered and received 6 converters.

The boards are very compact, not much larger than a matchbox.

They’re clearly used—or, more precisely, desoldered from some device. There are traces of potting compound and some bent leads, but all the components are intact, which is good to see.
The top side has a pair of inductors, several solid-state capacitors, and a few other small components. There’s an inductor on the input, protecting either the converter from power supply ripple or the power supply from converter ripple.

I found the marking G1208-20013120A on one side of the board.

This marking led me to the power supplies these converters were desoldered from. Here are a few links to reviews:
Cooler Master MWE 750 WHITE 230V V2 - link
Cooler Master MWE Bronze 650 - link
And also Chinese and Korean sites:
MWE 500 WHITE 230V V2 - link
Cooler Master New Thunder 500W - link
There I found not only photos, but also the specifications for these boards, including output voltages of 5 and 3.3 V.

It’s pretty clear that these are the same boards.

What’s curious, though, is that some power supplies list them as 16+16 A, or 110 W total, while others specify 20+20 A, or 120 W total.

But the board actually contains more than just voltage converters: it also has temperature sensors and a fan control circuit. One temperature sensor is mounted externally, and the fan speed is adjusted gradually based on its temperature. The second, an SMD sensor, is located between the inductors and protects the converter from overheating.

There are clearly more components on the underside, and only one board had no potting compound.

The converter is controlled by a dedicated dual-channel PWM controller, the APW7159C. Its output drives four switching transistors, FTD05N03NA, rated at 30 V, 100 A, 4 mΩ.

Key features:
The chip is powered from 12 V and has overvoltage and undervoltage protection. Its operating range is 6–14.4 V. It also has overtemperature and overload protection (by measuring the voltage drop across the high-side transistors), and an operating frequency of 50–400 kHz.

There’s also a typical application circuit. As you can see, the channels are almost identical, so it should be quite possible to change the output voltage and turn the 5+3.3 V version into the more useful-for-me 5+5 V version.
The example shown also has an output current of 30+30 A.

There are two more chips next to the converter that I couldn’t identify. I suspect one of them controls the fan.

The product comments also included photos showing where to connect the power and where to take the output voltages from.

I connect it to a power supply and apply 12 V. No-load power consumption is relatively high at 1.2 W.

The 5 V output is spot on, but the 3.3 V output is too high. I assume the extra “pin header” also has a remote-sense input for compensating for voltage drop in the wires. Without it connected, the converter outputs the maximum voltage of 3.4 V (limited in case the feedback wire breaks).

Since the currents are fairly high, I’ll test it with an electronic load rated for up to 30 A. The multimeter is connected to the output pads on the board.

Voltage regulation is simply excellent: across load currents from 0 to 25 A, the voltage changed by just 11 mV!

But that’s not all—the converter also delivered 30 A. To do that, though, I had to raise the input voltage to 14.3 V; otherwise, the power supply went into current limiting.
Unfortunately, in this mode the converter shuts down after about 10 seconds due to overload protection. The protection latches, so the output stays at 0 until I disconnect the input voltage.

I measured the board’s efficiency at the 5 V output in two modes, with input voltages of 12 and 14.3 V.
The graph shows higher efficiency with a 12 V input, peaking at an output current of 10 A. I’m planning to reconfigure the board for a 5+5 V setup. I need 40 A total, so I could use two of these boards to create four 10 A channels, giving me maximum efficiency and, accordingly, minimal heating.

Speaking of heating, I ran a quick test. I supplied 12 V to the input, loaded the 5 V channel to 10 A, and watched how it performed.
1. Temperature at the start of the test.
2, 3. Temperatures on both sides of the board after 20 minutes.

Then I raised the current to 15 A and ran it for another 20 minutes.
Yes, without active cooling, things don’t look great: the top of the board got almost 11 degrees hotter, and the inductor reached the highest temperature. That’s exactly why I thought of using two 10 A channels. With a little airflow, the board should run with plenty of headroom.

And the output looks great, too: here are the ripple waveforms with no load (first screenshot) and at 8, 16, and 24 A. Even at 24 A, the ripple was no more than 30–35 mV. It almost feels like overkill to power an ordinary battery charger with a converter this good :)

I did run into a small snag with the fan. As intended, I connected it to the board’s built-in connector, applied power, and started heating the temperature sensor. But nothing happened. A quick look at the circuit led me to conclude that the fan control is a bit unusual: both leads are switched. The positive lead is switched by a large transistor next to the connector on the top of the board, and the negative lead by a small SMD transistor. As far as I can tell, the large transistor provides linear speed control, while the small one simply switches the fan on and off.
By “scientific trial and error,” I found that one of the pins on the “header” carries a fan-enable signal. To turn the fan on, I fed 5 V from the converter’s output through a 680 Ω resistor. In practice, it’s better to use voltage from another source, such as the 12 V input, so the board won’t be left without cooling if the 5 V input shuts off. You can use a higher-value resistor instead of 680 Ω; this was simply the one I had on hand, and it worked for the test.
After soldering in the resistor, the fan began to ramp up smoothly as the temperature sensor heated up. Once the sensor cooled, the fan didn’t stop completely; it kept spinning very slowly. The review of a power supply with this board said that the fan shuts off completely.

At first, I thought I’d leave the modification for later, but curiosity got the better of me.
It’s all very straightforward: the board has two voltage dividers. R47 (12 kΩ) and R50 (3 kΩ) are for the 5 V channel, while R2 (12 kΩ), R46 (100 Ω), and R5 (5.1 kΩ) are for the 3.3 V channel. R50 and R5 are in the lower legs of their dividers, while R47 and R2+R46 are in the upper legs. In the second case, two resistors are connected in series—12 kΩ and 100 Ω—presumably to provide a small upward voltage adjustment for the 3.3 V channel.
To raise the voltage on the 3.3 V channel, either replace resistor R5 with a 3 kΩ one or solder a 7.5 kΩ resistor in parallel with it. I went with the first option because I didn’t have a 7.5 kΩ resistor on hand, but I did have some 3 kΩ ones—though they were a little larger.

The output voltage rose to the required value, and even a little higher.

Since this divider has a 100 Ω resistor in the upper leg, in series with the 12 kΩ resistor, I simply bridged it with a jumper.
By the way, on some boards the divider resistors are soldered in a “sandwich,” so the adjustment is done manually.

The 3.3 V channel now has exactly the same output voltage as the 5 V channel. I may adjust it down a little later, but first I’ll need to experiment to find out how far it can be lowered.

I’ll keep the conclusions brief: I really like these converters. If I find them at a reasonable price, they’re a “must buy”—compact, powerful, with decent efficiency, two channels, fan control, and protection against overheating and overload.
If anyone has seen them on AliExpress, I’d be glad to get a link.
As you’ve probably figured out by now, I need these converters to modify a multichannel battery tester. That’s why I need 40 A at 5 V, with an input voltage in the 10–14 V range. It helps a lot that the channels can be split up: I don’t need a single 5 V, 40 A converter; two 20 A units or four 10 A units will do. I may lower the output voltage to 4.7–4.8 V to reduce the total power required even further, since it will be powered by a UPS.
I just need to make a few more modifications for my application, and then it’ll be ready to use.
apw 7159 c, apw7159c datasheet на русском, taobao apw7159, apw 7159c fyfjhy, u6215 схема включения, https://www.kirich.blog/obzory/preobrazovateli/924-moschnyy-dvuhkanalnyy-dc-dc-preobrazovatel, dc dc доработка двойная питание, apw7159 подключение, apw7120 zamena, apw7159a отличия от apw7159c, apw7120 чем заменить, apw7159c datasheet, apw7159 dc-dc 5 3.3, u6215a схема включения, apw7065 характеристики, микросхема рт7120а, a7159, apw7159c схема включения, 7120 схема включения преобразователя, apw7089 datasheet на русском, apw7159 datasheet на русском, apw7089 чем заменить, apw7159 аналог, характеристики микросхемы apw7065, apw7159c за что отвечает
Questions and answers
How much current can the G1208-20013120A converter deliver?
It delivered 30 A in testing, but shut down after about 10 seconds due to overload protection. From 0 to 25 A, the output voltage changed by just 11 mV.
What is the ripple on the G1208-20013120A converter?
At a 24 A load, ripple was no more than 30–35 mV peak-to-peak.
Can the G1208-20013120A channels be changed to 5+5 V?
The author says the channels are nearly identical and can be reconfigured. To raise the 3.3 V channel, he changed resistor R5 and bridged a 100 Ohm resistor; its output then matched the 5 V channel.
This model is included in the summary table: Comparison of DC-DC modules: step-down, step-up, and universal
The figures from this review are in the measurement database: Converters
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments3
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister

Comments are published in their original language.