ZY1276, a universal USB meter from YZXstudio
This is far from the first review of this device, but perhaps someone will still find something new here, especially since this is actually a review not only of the USB tester, but also of its accessories.

As you may have noticed, I ordered more than just the tester itself—I also got a few odds and ends. So the complete set includes:
1. ZY1276 tester
2. Metal top and bottom covers.
3. Bluetooth module
4. Programmer

I'll start with the protective cover set. It cost $1.31, excluding shipping.
Originally, the top and bottom of the tester are covered with fiberglass panels. This is simple and convenient, but in my opinion it looks very cheap—though, of course, that comparison isn't entirely fair.
This kind of enclosure is more typical of hobbyist projects, not a reasonably serious device, since the enclosure is effectively open.
The covers won't fix the design's shortcomings, of course, but at least they'll look better.
The covers are metal, and the markings appear to have been laser-etched. I drilled them during the project: they're made of ordinary steel, fairly hard, but relatively easy to drill. The edges are roughly finished, with no chamfer.
The second accessory is an ST-Link programmer. It also came with spring-loaded contacts, though for some reason they were in the bag with the covers. The set cost $3.41.

I actually needed the programmer less for updating the tester's firmware than simply to have one on hand, since I'm increasingly coming across devices based on these microcontrollers. Maybe this will give me at least a little incentive to try learning how to program STM controllers.
The case is aluminum, with USB on one end and a 10-pin IDC connector on the other. The programmer's case has the connector pinout printed on it, which is very convenient.
There are six spring-loaded contacts, although in practice you need no more than four, and probably only three. The contacts are convenient, but very difficult to insert into the connector the first time.

The USB tester under review can't connect to a computer out of the box, but you can add a Bluetooth adapter.
It's sold as a board and costs $4.59.
But there was a mix-up in my case: I received the required board, but the Bluetooth module itself was missing :( I even started checking the reviews on the product page to figure out whether the seller was at fault or I'd misunderstood the description. One review included a photo that clearly showed the module should have been included.

And, of course, the USB tester itself, which cost $32.46, excluding shipping. By the way, shipping within China doesn't depend on the number of items from the same seller, so the cost was split across the four orders.
The tester comes in a tin box with a window covered by clear film. It's cheap and simple, but given that the tester itself has no screen protection, the packaging may actually be useful.

Before installing the metal covers.

The short ends have the usual USB-A connectors: male and female, respectively.
The sides have:
1 - microUSB and USB Type-C inputs, as well as the control button.
2 - USB Type-C output.
I have no particular complaints about the number or types of connectors, but having just one control button is a drawback. I got pretty good at operating the tester, but at times it was very inconvenient. Even one more button would have made things much easier.
Also, the tester has no separate power input and is always powered only by the source being tested. Why they didn't add a separate connector is a mystery.

The device is extremely easy to take apart: you just need to remove eight screws. By the way, the screws are small and non-magnetic, so be careful not to let them "run away" across the table. There are no spares :(

The manufacturer fitted some decent connectors. At least one of them is made by Molex, and in general I noticed that the connections are noticeably better than on cheap knockoffs, although I didn't specifically measure the contact resistance.

Although the tester is a decent size, the electronics inside are quite compact. The display is what determines its overall size, really.

But in fact, the circuit design also has some notable differences from the simple, inexpensive models.
A 32F030F4P6 microcontroller controls the entire measurement process and displays the results. Nothing new there, I'd say.
What's good, though, is the fairly decent Dale shunt, with a resistance of just 12 mΩ, 1% accuracy, and 75 PPM. Better still, the shunt signal goes not directly to the microcontroller, nor even through an intermediate op-amp, but through a dedicated INA226 chip.
There's an RC16 FRAM chip nearby.
The whole thing is powered by a low-dropout linear regulator, the SE8533-HF.
The chip marked PBAB H1B presumably handles the Power Delivery function.
It's worth noting that all the power traces are a decent width, and that the current-sense shunt is on the positive supply rail, not the negative one.
Compared with the circuit design of its closest equivalent, the UM24C, this one is much better thought out. The UM24C may be quite a capable device, but its circuit design isn't much different from that of ordinary USB testers.

But back to Bluetooth. As I already mentioned, the adapter board was missing the most important part: the Bluetooth module itself. The boards are also noticeably different, which seems rather strange to me. The new board has room for another connector and a switch (presumably). It also has connection pads that are probably intended for a battery. All in all, a complete mystery.

I found a photo of the board on the product page, showing how it was originally intended to look.

I didn't look for it on AliExpress; first I checked whether it was available locally and how much it cost. The result was a pleasant surprise: not only did I find it without any trouble, but the price—less than two dollars—was more than reasonable.

Of course, I could have tried using any other module, even one I had lying around at home, but I wanted to install the one the board was designed for, since the PCB layout is specifically made for it.

The module's full name is HC-05-SPP-C, in case that's useful to anyone.

I soldered the module in place, but only soldered the pins that were actually used, just to be safe. It connected without any problems. The password is 1234. I was a little surprised that the LED on the board didn't react to the connection at all. I took a look and realized I'd forgotten to solder its contact to the module. But the LED still didn't work after that. It turned out I'd soldered it in backwards!
I had to desolder and resolder the LED too; it's to the left of the contact group in the photo.
Speaking of the contact group, the manufacturer used three spring-loaded contacts. That would be fine, except the ground connection runs through the mounting posts, even though the board was originally designed for four contacts. That's a fail on this point; don't do it this way.

It does look better in the metal "case", at least in my opinion.

Now there's also a Bluetooth switch on one of the long sides.

And here's the tester next to its younger "sibling".

The screen is pretty good: quite bright and sharp, though the color scheme seems a little harsh to me. It looks a bit washed out under the flash, but overall I have no complaints.

The device has 7 main operating modes, which you cycle through by briefly pressing the control button. Since the tester starts up in the last mode used, I don't even remember which one came first, so I'll start with what seems to me to be the clearest.
1. Voltage, current, power, capacity in Ah and Wh are measured. Temperature measurement is also available, but in my opinion, this last feature is pointless.
2. Voltage, current, power, equivalent load resistance, and runtime measurement. This mode, like the previous one, can save measured values to memory cells. There are six cells; switch between them by holding the button, and clear all values in a cell by holding it even longer, for about 5–6 seconds.
3. Displays voltage, current, power, and data from the data lines, along with the corresponding charger operating mode.
4. Virtual "oscilloscope". Displays the dynamic characteristics of the power lines and data lines.

1, 2. Cable resistance measurement modes: standard and four-wire.
3, 4. Simplified mode. It displays only voltage, current, and power, but lets you rotate the display in 90-degree increments. I don't find this mode very convenient: in the name of marketing, the manufacturer decided to update the readings as quickly as possible, resulting in a refresh rate of around 10 Hz. Not only is that not particularly useful, it's also annoying.
The last mode turns the screen off.

Now for the settings—there are a lot of them.
1. Hold down the control button, then connect the power, and the tester will enter settings mode.
2, 3. All the modes. The firmware version is also shown here: 3.35F
4, 5. Screen brightness in normal (1–20) and power-saving (0–19) modes; the defaults are 10 and 1, respectively.
6. Time before switching to reduced brightness: 0–255 minutes; the default is 3 minutes. Up to 10 minutes, the setting changes in 1-minute increments; above that, in 5-minute increments.
7, 8. Select the font and language (English or Chinese).
9, 10. Output format for an external device: ASCII or HEX. Transmission interval: 0.36–60 seconds. The function is disabled by default.
11. Current threshold for the tester to start counting capacity in Ah and Wh: 0–5.1 A. Up to 100 mA, the setting changes in 10 mA increments; above that, in 100 mA increments.
12. With no load, the tester may sometimes display small, random current readings, usually in the last digit. You can calibrate the zero to eliminate them.
13, 14. Background logging of results, up to 48 hours.
15. Refresh interval for the virtual "oscilloscope" display: 0.1 to 20 seconds per division; the default is 3.6 seconds.
16. Clear measurement memory.
17. Calibrate the built-in thermometer. This is generally a useful feature, but since the thermometer itself is pointless, it is pointless here too.
18. Voltage calibration. Apply 10 V to the input and start calibration mode. The voltage must be set very accurately, so I don't recommend doing this unless you have the appropriate instruments.
19. Current calibration. As in the previous step, but connect a load drawing a stable 2 A to the output.
20. Save calibration settings. While calibrating the voltage, I accidentally started the process at 5 V, and the tester ended up reading twice as high. Resetting to the defaults restored everything. But I don't know what would happen if I chose Save.

Operating mode that detects voltage on the USB data lines.
1, 2, 3. The same power supply, but two different outputs, so the charging modes are different.
4, 5, 6. A power supply with QC support. Interestingly, it first displays QC 12V mode, then after a while USB 2.0 Full. The voltage stays the same. Photos 5 and 6 show the same setup, but connected through an extension cable and directly to the power supply, respectively.

USB cable resistance measurement function.
For this test, I used two cables, one long and one short, as well as an electronic load.

1. Set the load current to 2 A. The tester measures the voltage at its input and uses it as the reference.
2. Connect the tester's input to the power supply through the cable being tested, rather than directly. The tester measures the voltage drop relative to the reference and calculates the cable resistance. The photo shows the long cable.
3. The same test, but with the short cable. Yes, that's a strange result. I repeated the test several times, and the result was quite consistent.
4. There's also a four-wire test option. In this mode, the data lines are used as the measurement pair. I tried running this test without the additional board, but apparently I connected something incorrectly and couldn't get a result. I'll have to experiment some more.

1. In data-line mode, press and hold the control button, and the tester will prompt you to enable the "fast" charger function test mode. In this mode, it can emulate commands from a device so the charger can output a higher voltage. Be careful not to use this mode with devices that don't support a high input voltage.
2, 3. Supported emulation modes.
4. For the sake of experimentation, I ran the auto test with the power supply from a Lenovo P2. Interestingly, the test didn’t show that the power supply can output up to 12 V—9 V was the maximum, even though the tests above showed that it outputs 12 V without any problems.
This is a very useful feature, especially because it works with a large number of devices and, in particular, because PD support is listed.

Virtual “oscilloscope.” Another very interesting feature that lets you monitor voltage and current on the power lines, or voltage on the signal lines, in real time.
1, 2, 3. Voltage and current with a regular 5 V power supply. While it’s running, the automatic mode selection adjusts the display so the signal is as visible as possible. If the signal’s amplitude takes up a large part of the screen, it selects 1–2 V per division; if it’s small, it selects a lower value, such as 0.05 V.
4, 5, 6. The same thing happens when monitoring the data lines. By the way, on the right you can see the voltage on these lines change as QC negotiates when charging starts. In reality, the lines are different colors, but they came out the same in the photo.
7. The most sensitive setting: 0.01 V per division.
8. Automatic adjustment of the current and voltage scales works independently.
9. If you press and hold the control button, the tester switches between monitoring the power and data lines. There’s also a third mode: it briefly displays READ, then DONE. I assume it’s supposed to receive some data and then confirm that it was received. But since there’s no manual, that’s just a guess.

I didn’t record my own video of it in action; I just found the closest one I could.
Here, someone measures the current drawn by a fan using the fastest display mode.
<video>https://www.youtube.com/watch?v=BkaZe3HjkhE</video>
And, of course, a few tests.
First, the tester’s own current consumption.
1. At a supply voltage of 5 V
2. At 25 V
3. Power-saving mode.
4. Screen completely off
In my opinion, its power consumption is fairly high. It isn’t included in the measurement results, but if you’re testing battery capacity, for example, it will add some measurement error.

Checking voltage measurement accuracy. At one point I accidentally forgot that the maximum input voltage is 24 V and tested it up to 27 V. It survived :)
The accuracy is quite good, although there is some nonlinearity. For example, this particular unit reads low by more at 5 V than it does at 25 V.

The current measurement accuracy test took longer, so I’ll just show how it went and put the results in a table.
Up to 2 A, I used a small homemade load; for currents up to 5.1 A, I used a more powerful one. Since I don’t have any USB connectors of suitable quality, I simply soldered wires to the circuit board. Though, to be honest, I’m skeptical of currents this high through a USB tester in general.

During the test, I just wrote down the readings and only looked closely at the results after filling in the table. Overall, the accuracy is decent, but in my opinion it could be better. Above 0.5 A, the ZY1276 starts to read a little high. I’d also say that all those digits after the decimal point are more for show than any practical need. In reality, the last digit could easily be dropped, just as on the voltmeter. It serves no purpose at all, and removing it would improve readability.

Another important test: checking whether the capacity calculation is correct, especially after my review of a tester with “Chinese math.”
There were no particular problems here either. After half an hour, it had accumulated 2.5057 Ah; my calculations said it should have been 2.502 Ah.
The timer is also quite accurate. Over the half-hour test, it gained 1 second, so at most 2 seconds per hour.

But the data transfer capabilities were a big disappointment. The RD UM24C I mentioned above has fairly capable software, but this one offers almost nothing. All you can get is voltage and current data. I really hope the manufacturer will eventually get around to making their own software.

While searching for documentation, I also found a new firmware version, 335H. Mine is running 335F, so of course I wanted to update it, if only as an experiment.
Unfortunately, the programmer can't see the board. I updated the programmer's firmware,
I connected it via the GND, SWDIO, SWCLK, and 3.3 V contacts, which are brought out to the pads.
If anyone knows what I'm doing wrong, please let me know and I'll try to check it.

With a little help from everyone, I figured out how to update the firmware, so I wrote up the instructions below.
Enthusiasts wrote some simple software themselves; you can download it here.
It displays the current processes—or, more precisely, simply measures current and voltage and plots them as it goes.

You can

Right at the very end, I finally installed the lower metal cover. To keep the Bluetooth board in place too, though, I had to literally “file it down.”
I slightly enlarged the holes in the Bluetooth adapter board and the metal cover so the original screws would be long enough. This was the modification I was worried might cause problems, since the mounting posts also serve as the common connection to the Bluetooth board, but everything worked out fine. It also had virtually no effect on Bluetooth performance; at least, everything works from a few meters away from the computer.

Video version of the review
To sum up.
On the plus side, I have to mention the device's well-designed circuitry, quality components, extensive functionality, high accuracy, and even a degree of ease of use—though that last point may seem a little odd given that it has just one button.
On the downside, the remote-control options are poor, and the display updates too quickly, sometimes becoming distracting. In my opinion, removing the last digit from the display would only have made the device better.
And then there's the case. Honestly, this “country style” seems more appropriate for inexpensive DIY projects, or simply for original devices. On a fairly high-end measuring instrument, it not only looks strange but is also somewhat unsafe, since something conductive could get inside and simply destroy an otherwise good instrument.
After writing the review, I finally found the manual: firmware version 335 in Chinese and 333 in English.
I’m not counting the missing Bluetooth module as an issue, since it’s clearly an isolated case and has nothing to do with the instrument’s specifications, but it’s still disappointing.
I bought it through the agent yoybuy.com; the whole set cost about 42 dollars, and shipping costs depend on the country.
вeken bk 3513, usb тестер zy1276 купить, 32f030f4p6 arduino, usb-тестер, цифровой мультиметр с передачей данных usb, по для тестера zx1276, zy 1276 pd, yzxstudio usb тестер, yzx studio, yzxstudio diy, yzx studio usb тестер, usb измеритель тока и напряжения кнопки, прибор для измерения напряжения с передачей его на плату через usb, can not connect to target! if you re trying to connect to an stm32w1xx device, please select normal or hotplug mode from target >settings menu. if you re trying to connect to a low frequency application , please select a lower swd frequency mode from targe, измерители тока с usb, измерение напряжений через usb, ztx studio usb тестер zy1276, измерители тока c передачей на компьютер, usb тестер подключение компьютеру, измерители напряжения и тока usb, тестер zy1276, измеритель напряжения с передачей данных на пк по usb, usb тестер 1280, usb tester zy1260, измеритель напряжения с передачей данных на пк по usb., USB измеритель, USB тестер, измеритель напряжения и тока, тестер напряжения, измерительные устройства
Questions and answers
What measurement components does the ZY1276 use?
It has a 12 mOhm Dale shunt with 1% accuracy and an INA226 chip that measures the shunt signal.
Can the ZY1276 USB meter connect to a computer?
The meter cannot connect to a computer on its own, but it can be fitted with a Bluetooth adapter. The adapter package the author received was missing its Bluetooth module, which he bought separately.
What drawbacks does the author find in the ZY1276?
The author criticizes its open case, single-button operation, limited remote-monitoring options and overly rapid display updates.
This model is included in the summary table: Comparison of measuring instruments reviewed on the blog
The figures from this review are in the measurement database: Measuring instruments
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister











