/       /       /    LED panels, controllers, or how to build an LED screen, part two
Support the project on Patreon


LED panels, controllers, or how to build an LED screen, part two

$40.69
Go to store
In the previous part of the review, I talked about the LED panels and controllers. In this second part, I’ll focus more on the software, testing and demonstrations. I’ll also talk about the problems I ran into—because of course there were some.

After playing around with the panels and controllers, it’s time to install them. But first, let’s look at how it’s done properly on an industrial scale.
Since the panels are relatively fragile, they’re assembled into modules using what are called “cabinets”—or simply, chassis.


These structures range from relatively compact to quite large. They can also be square or rectangular, depending on their intended use.
The chassis hold not only the panels, but also the control boards, power supplies and fans to cool the whole assembly, since its power consumption can be around a kilowatt.


Cabinets often have mechanisms for joining them together, as well as sealed connectors for assembling them into a wall.
The photo shows the assembly sequence and the finished structure from the back.


In general, this kind of construction is useful not only for easier installation, but also for easier transport. The wall can be taken apart into modules again, packed into special crates and moved from place to place in pieces.


Then it can be assembled into a new wall, whose dimensions may be dictated not only by the required aspect ratio, but also by whatever size is needed.


These chassis are quite expensive—more than the entire budget I mentioned at the beginning of the review. Since we’re not exactly rolling in money, we had to build our own structure.
As I’ve already mentioned, a friend built it. The materials used were drywall framing profiles, metal-plastic composite (a plastic sheet with metal on both sides), glass, small brackets and rivets. Standoffs were then screwed in to secure the rear cover.
There were two panels: 256×128 and 256×64 pixels.


The photo shows an intermediate version, as it arrived at my place. After I debugged the software and configured it, it went back to my friend, who then finished the job: aligned the panels, tidied up the wires and secured the boards (for now, just one board).


So, the panels are all set up. Now it’s time to wrestle with the software, describe it and run some tests. This section will be quite long too.
Software was a major factor when choosing a controller, since so much depends on it, and not all software works with different controllers. In other words, the software is tied to the controller model.

First, I wanted to see how it worked at all. I started with the D10 controller, but ran into some difficulties, so I set it aside for a while and moved on to the D30.
Launch the program, select the controller version and enter the panel’s resolution. All the operations are performed in the window shown here. Below the resolution settings, there’s also an option to rotate the image by 0, 90, 180 or 270 degrees. The button is tiny and easy to miss.
I connected over the local network, and the software really surprised me: it found the panel and connected to it automatically. Five stars.


For the test, I used an image of a clock and turned on the “running fire” border effect.


To make things easier, I started experimenting with the smaller panel, since it fit on the table just fine.
In the end, I could see only two rows—the first and the third—if you divide the panel into four sections. I saw exactly the same thing when I tested the D10 controller.


I won’t say how long I spent experimenting, or how many developers’ relatives I thought of before I figured out what I’m about to show you.
The discs originally came with documentation, but it didn’t match the program. There were also two programs: HDplayer (the one in the screenshots) and HD2016. I spent a long time wrestling with the second one, but it’s very difficult to configure, and its functionality is noticeably worse. One came on one CD, the other on another, but I could read only one disc, so I ended up downloading everything from the internet.

So.
In the settings, I found an option to select the panel type, but 64×64 isn’t there. Not at all. As in, absolutely nowhere. Fine—after some trial and error, I found an option that displays all the rows and even gives a normal-looking image. The catch is that only three of the four panels work properly.



I found it, but I can’t save it. The program says something is missing. What’s missing is the horizontal resolution. It turned out that it (and not just it) depends on a whole bunch of factors.


Once again, through a no less scientific process of trial and error, I found that increasing the bus frequency also increases the maximum horizontal width. It was initially set to 20 MHz; at 25 MHz, four panels are enough, and at 31.5 you can use five panels.


Now that's more like it.


Next, I change the resolution from 256x64 to 256x128, since this controller was intended for a large panel.
The “Use hardware settings” tab lets you retrieve all the settings from the controller board.


Of course, the image no longer fits, since it now effectively takes up half the screen.


Assembling the rest is straightforward. The main thing is to arrange the panels so that the output of one is next to the input of the next. It doesn't matter which row is on top or bottom in this case, since the software lets you flip the image any way you like.


It's impossible to plug the data cables in the wrong way. If in doubt, use the red wire and the notch in the connector as a guide.
You'd have to be pretty strong to get the power wiring wrong, because it's really hard to mix up here. One cable can power two panels.


When connecting to the power supply, you'll probably find that it has fewer terminals than there are wires. Just put two wires in each terminal. You also need to power the controller; it's best to use separate terminals for that. Positive is red (VCC or +V), negative is black (GND). Sometimes a cable for powering the controller is included, but more often it isn't. Just use any cable with a cross-sectional area of 0.5 mm².


The controller is temporarily connected for testing, so it's just lying there—or rather, hanging there, since the panel is normally mounted vertically.
The first pin on the controller connector is marked; it connects to the panel connector pin marked with the red wire.
In my setup, the top panel ended up connected to connector number two, and the bottom one to number one. But even if you connect them the wrong way around, the worst that can happen is that nothing will display, so don't worry.


The temporary setup is ready for more experiments.


You probably think my adventures ended there? Not even close. You may remember that I initially had problems with the blue and green colors being swapped. Well, the same problem showed up on the large panel, since it turned out that panels from different shipments were mixed together in it.
Yes, the controller can change the colors any way you like, but... only for the entire screen at once!


After browsing the internet for a while, I realized things weren't quite so hopeless. The supplementary materials will include a file with everything I found.
The panels have an interface connector that carries all the necessary information. Most likely, you'll have the first version, but the second and third versions are also possible; they have minor differences that won't affect us. The pinout is usually printed on the panel's circuit board.
There's also a chance you'll get the fourth version. Fortunately, it's easy to recognize: it has two input connectors and two output connectors. This version is quite rare, though. In any case, after reading what I did next, I think you'll have no trouble figuring out what to do.


To make things easier, here's the location of the cable's first pin. By the way, there's also an image below explaining that no matter how you connect the cable, the pins will always be in the same positions.


This image shows how the cable pins map to the signal lines.


Yes, the letters RGB simply indicate the corresponding colors. The panels receive synchronization signals, panel section selection, and color information.
In our case, there are two lines for each color.


Obviously, nobody's going to solder the panels, but changing the wires in the cable is quite easy.
Take the cable. We need wires numbered 2, 3, 6, and 7.
Identify these wires (you can mark them with a marker) and cut them
Strip and tin them.
Solder them crosswise (2 to 3, 3 to 2, 6 to 7, 7 to 6) and insulate them with heat-shrink tubing.


As an experiment, I first resoldered just one ribbon cable. The result was immediate: one section of the panel started working properly.
Just in case, here's what to do if this happens: you don't need to resolder all the ribbon cables. Simply arrange the incompatible panels in a row and modify only the cable between them and the compatible panels; the others will also display correctly.
In this case, the signal went to the left pair of panels (top/bottom), followed by the modified ribbon cable.


We modify the second ribbon cable, and enjoy the result.


Someone once wrote to me that you could use a monitor with an IPS panel instead of an LED panel: it's cheaper and just as bright.
This photo clearly shows how an LED panel at about 66% brightness compares with a tablet at 100% brightness.
And P3 panels are a little less bright than P4 panels, at least the ones in this review. That's not even taking the contrast level into account.


But my adventures didn't end there. While playing around with the test modes, I noticed an image defect on the second type of panel. Not only is the white not pure white but has a greenish tint, there are also visible squares. This appears in the 50% fill mode, i.e. when every other LED is lit.
The first type of panel, meanwhile, displays perfectly.


The squares aren't visible in an actual image, but the difference in tint is noticeable, especially against white and blue backgrounds.


The software lets you adjust the color temperature and correct the colors, but again, only for the entire screen...
In this case, you'll have to settle for something in between.


Above, I said the panel was running at 66%. The thing is, brightness is limited not only by the "brightness" slider in the settings, but also by the panel's own operating modes. For example, brightness is affected by the clock frequency, the number of brightness levels, the refresh rate, and so on. Changing some parameters can bring it up to 91%. I got 95 or 96, but used 91 as an example.


Since I had two types of panels, I tested the power consumption of both in different modes: at the standard brightness of 66% and at the increased setting of 91%.
The thing is, the second mode degrades the image—or rather, the quality of video and photo playback. If you use the panel as a scrolling display, there's no difference.
Each test measured the current draw of four panels. The controller was powered separately and draws about 0.5-0.7 A, depending on the operating mode.

First, the first type, which was used in the smaller display.
1-4. Brightness at 66%. Three colors and white.
5. 50% white fill
6. Maximum current during the test video.
7-10. Brightness at 91%, increased with performance limited.
11. 50% white fill
12. Maximum current during the test video.


1. Current draw of the panels themselves. A reminder: the test used four panels.
2. Minimum current during the test video.
3. Average current during the test video.


Everything I tested the first time, in the same order, but for the second type of panel.
So, at normal brightness (66%), each panel draws 16 W, and at maximum brightness (100%), up to 24 W. The whole display (8 panels) draws up to 133 or 200 W. I think it's now clear why it's so much brighter than a monitor.


Now I can describe the software and how to use it.
I used HDPlayer version 5.3.98.0. The workspace is a virtual screen that shows everything we do in real time, but isn't linked to what's currently displayed on the actual screen.


Basic device information and a few settings, such as whether to play a program once or repeatedly.
As I mentioned, not all programs are equally versatile. For example, HD2016 is more flexible, but less convenient to use.


1. Brightness adjustment: manual, automatic (if a sensor is connected), or scheduled.
2. Time
3. Schedule for automatically switching programs.
4. Local network.


All other settings are accessible only after entering a password. The password is the same everywhere: 168. The previous software used the same password, too.


Data transmission settings for the panel. There are a lot of them, and some depend on each other. For example, increasing the number of brightness levels reduces the range over which the refresh rate can be adjusted.


Selecting the type of connected panels. For some reason, my 64x64 panels worked with the 64x32 option, and even with the wrong hub type.


In “preset” mode, you can try to configure the panel mapping manually, though I couldn't get it to work.
First, select the controller type, then choose the panel's actual brightness as it is currently displayed.


Next, select the color output order and change it if necessary.
Then specify how many pixels light up in the first and second cases.
Finally, a black area with a blinking pixel appears, and you have to select it on the virtual screen. Then select all the pixels in sequence, first horizontally and then vertically. It's pretty quick, but it didn't help me.


Color correction mode and changing the pin assignments on the output connectors.


If the program can't identify your controller, it will offer to do it manually. It should be possible, but in my case the program identified the controller.


1. System settings menu.
2. Menu for accessing the “cloud.”
3. Test mode. You can also start a test by pressing the button on the controller itself, but this is the extended version.
4. Firmware update. The firmware is downloaded directly from the HDplayer software.
5, 6. Various additional options and the program's language selection. The translation is pretty rough, that's for sure.


Now let's take a brief look at the main features for working with images and text.
The main advantage isn't just video playback, but also the ability to freely overlay one thing on another. There's one catch, though: when displaying the temperature, the letter C doesn't appear. To make it show up, you need to change the font. You can use a different font for each zone.
The temperature can be displayed as XX or XX.X, but in the latter format it always showed 0 for me.


In video playback mode, you can add several clips, but they will play one after another; you can't display two clips at the same time.
You also can't resize the area after adding a video to the screen. In other words, select video mode, choose the layout and the position of the window, then add the video. If you want to change the size, repeat the process. You can move the selected area without any problem. The video plays in the software, complete with sound. There's also an option to adjust transparency.


There are also plenty of fonts and effects to choose from, and many effects have various options, such as display time, fade-in and fade-out time, and independent effect selection.


The controller can get weather data from the internet on its own, but Russia is the only CIS country available, and the translation leaves a lot to be desired. Cities aren't listed alphabetically, but pressing a letter on the keyboard automatically searches for names starting with that letter.


A huge advantage of working over a local network is that after clicking the Send button, you can see the result on the screen in 10-15 seconds.


Panel temperatures after an hour of operation.
1. Front
2. Back
3. Control board


Encouraged by this success, I decided to go back to the first controller, which was intended for use with the small panel.
I connect it and start it up.


And I get everything except what I need. I tried every mode and every panel option, but in the end I could only get two of the four rows to work. And sometimes it looked absolutely awful...


Remembering that there was an option to update the controller software, I went there and updated it. But even though I got a message saying the update was successful, the firmware version hadn't changed, so the result hadn't changed either.
After exhausting myself with unsuccessful attempts, I resorted to the last measure and wrote to the seller, saying I had a problem.
He replied with a question: what panels and scan mode was I using?
I sent a photo and said the panels were 64x64 with 1/32 scan.

The astonishing reply: this controller can't work in 1/32 mode, only up to 1/16.

I said, how can that be? Your page says 1/32, and what's more, you specifically recommend the HD-D10 for panels like these. There's even a photo.

In the end, the seller changed the recommendation on the product page, but I wasn't satisfied and got an offer of a $5 refund.
I replied that this wasn't acceptable and made two counteroffers: 1. Open a dispute and refund $20. 2. No dispute, but sell me an HD-D30 with a $20 discount.
The seller agreed to the second option without any questions. The controller is already on its way.


Things are more complicated with the panel seller. A remarkably strange person. He replies once a day with a short sentence, and the whole conversation feels like a dialogue between a blind person and a deaf person.
In the end, I offered him three options: 1. Explain how I can solve the problem. 2. Open a dispute and refund the cost of two panels. 3. Send two replacement panels.
He says nothing. I opened a dispute, and now he wants me to send six! panels back. The whole story is actually more complicated, but it would take too long to recount. I don't know what to do with him yet.


Anyway, I'll deal with the sellers later. On to the add-on.
The controller supports connecting a temperature sensor, for example a DS12B20 in this case.


There are connector pads on the board. You can connect things like a temperature sensor, an IR remote receiver, a light sensor, or a humidity sensor. I only needed the temperature sensor, so that's all I'll cover here, but I'll add the information I found about various sensors and controllers to the archive.


I sketched a diagram as a guide; I think it's clear enough.


I connected the sensor with ordinary, unshielded wire. It's about three meters long, and it works fine. But for reliability, I'd recommend using a cable; I'll probably do the same here.


Since the controller is sometimes hidden inside an enclosure, it's convenient to bring the USB connector outside using a short extension cable. You can do something similar with the Ethernet cable: run a patch cable inside and bring out a female-to-female coupler that can be mounted on the enclosure.


As an add-on and a brief demonstration, I made a video showing the connection process and the screen in operation.
Unfortunately, the camera can't even come close to capturing the brightness, vividness, and contrast, especially in the part with the two scrolling test lines, but I did my best.


For comparison, the first version


And the second.



While preparing the review, I remembered that there are also very small LED panels, known as badges. They have their own software, called HDsmart, which is also available in Russian. These panels cost about $9, excluding shipping.


It probably makes sense to show the largest screen, too. It's 353 meters long and installed on the facade of a building in Jakarta, Indonesia.


So, what can I say in conclusion? Basically, we got what we wanted, but there are a few caveats.
The image quality, and especially the functionality, are a huge step up from the previous version.
The previous panel struggled even with fast text scrolling; here, everything flies. It's easy to control, and I liked the software, but while I was preparing the project, near the end, it unexpectedly crashed with an error. So I strongly recommend using the Save button.

The downsides are some difficulty with setup and the panel seller's truly appalling attitude.
The first time I bought panels, one had a dead pixel (see the first review), and the seller offered a reasonable refund himself.
The controller seller was also accommodating, replied quickly, and was easy to reach an agreement with.
But the seller of the panels reviewed here is something else. He replies once a day and is completely clueless, both on AliExpress and on Skype. Before ordering, I wrote to him twice saying I needed 12 panels and would order them in two batches at the same time, but he sent different ones. On top of that, one batch had mixed-up colors and a defect. Fine, I asked for a $41 refund (the price of two panels, excluding shipping). They want 6 pieces back, even though they previously said they had no replacement panels.
In my opinion, the compensation amount is quite fair (41 out of 300) for the time I spent investigating the problem and fixing it myself.

As promised, here are the extras: software, instructions for connecting to Arduino, connecting sensors, panel manuals, setup instructions, and so on — Google Drive and Yandex.

And here are the links:
1. 12 LED 64x64 panels cost $300 including shipping ($20.5 per panel plus shipping)
2. HD-D10 controller (about $30, excluding shipping)
3. HD-D30 controller (about $40, excluding shipping)
4. Power supplies on AliExpress — one, two.
5. Panels from the controller seller — link.

That's all. I really hope this information was useful.
$40.69
Go to store
This page was found when searching for:
aboled что это, датчик температуры для hd u62, экранчик из электронки подключение, лед панель белый текст какой контроллер, управление светодиодными панелями, работа с mr playre для лед панелей, принимающа якарта и контроллер лед панелелй в чем разиличия, подключение контроллера hd c35, схема подключния светодиодного дисплея evershine es-p2-i, как подобрать контроллер для лед экрана, самодельный монитор из светодиодных панелей, настройка лед экрана, типы электрических разъемов лед панели, 5, управление светодиодными панелями 2.5 мм, монтаж датчика на контроллер hd схема, разработка контроллеров управления led панели, как подобрать контроллер lcd, hdplayer led экран программа, как работает led panel, светодиодный экран контроллер, подключение датчика освещенности к контроллеру hd, какой контроллер выбрать для светодиодного модуля q4y20, лед полоска из дисплея подключение без контроллера, с35 с19 а239а видео панель лед

Questions and answers

How did the author assemble a screen from 64×64 LED panels?

Instead of expensive industrial cabinets, he used a homemade frame made from drywall profile, metal-plastic sheet, glass, brackets, and rivets. The resulting panels had resolutions of 256×128 and 256×64 pixels.

How do you configure the HD-D30 for four panels?

Select the controller version and panel resolution in the software. The author found that a 25 MHz bus frequency provided enough horizontal width for four panels, while 31.5 MHz allowed five.

What problems came up while testing the LED panels and software?

Configuration was difficult because settings depended on several factors, and the software unexpectedly crashed, so the author recommends saving the project regularly. Some panels arrived with swapped colors and a defect, and the seller was slow to respond.

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments8

Comments are published in their original language.

  1. Арсен
    21 September 2017 21:36#1
    Привет Андрей!
    Мало того что с тобой общаюсь по скайпу, все ровно хочу оставить отзыв и тут.
    Хороший обзор, ну можно даже сказать суперский. ТАК ДЕРЖАТЬ!!!!
    Все понятно и внятно рассказанно.
    С твоей помощью собрал бегущую строку. Большой тебе РЕСПЕКТ.
    Спасибо тебе за твое терпение и помощь.
    Уважаемые читатели этого блога, просьба к вам всем, таких людей как Андрей, который сидит ночами после работы и делает обзоры для вас и нас всех взятых, надо уважать и поддерживать этот блог.
    С уважением к автору обзора от Арсена. Израиль!!!!
    P.s Процветания и в дальнейшем тебе дружише!!!!!!!!
    +2
    1. 22 September 2017 21:52#2
      Спасибо, неожиданно, но очень приятно, надеюсь что у Вас все будет работать нормално :)
      +1
  2. Андрей
    25 January 2018 18:35#3
    Спасибо!
    Очень доступно написано. Спасибо за информацию. Я тоже хочу сделать полноцвет для своего магазина.
    0
    1. 1 February 2018 22:10#4
      Те, кто видел полноцветную нормальную рекламу, обычно к простым возвращаться уже не хотят :)
      +1
  3. Дмитрий
    3 September 2018 14:23#5
    Добрый день. Вопрос появился. У нас панели с контроллером HD-D30, показывают часы и температуру. Часы отстают в среднем на 2-3 секунды в сутки. Это нормально, может можно как то подкорректировать?
    0
    1. 4 September 2018 00:23#6
      Формально - нормально, но реально, я бы был недоволен. Подкорректировать вроде нельзя, по крайней мере я не вижу на плате отдельного RTC и кварца :(
      0
  4. 17 February 2020 21:01#7
    Здравствуйте!
    Столкнулся с проблемой выбора контроллера, остановился на модели Huidu HD-C35C и тут возник вопрос, а для чего нужны принимающие карты ? Обязательны ли они вообще ? Как я понимаю они нужны только в том случае, если вы собираете экран большого размера из раздельных кабинетов ? Буду очень признателен если поможете с этим разобраться.  confused 
    0
    1. 20 February 2020 04:46#8
      Как именно принимающие карты Вы имеете в виду? 
      0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister