/       /       /    Full-extension stainless steel telescopic slides
Support the project on Patreon


Full-extension stainless steel telescopic slides

$12.88
Go to store
For one of my projects, I needed full-extension drawer slides. They’re used all the time in ordinary furniture, and of course I could simply have gone to a store and bought some, especially since they cost around $2–5 there. But there was a catch: I needed stainless steel slides. More on that in the review.


Not long ago, I posted a video about the end of the saga of renovating my apartment. At the time, I also said that it wasn’t actually all finished yet, and one of the things still left to do was the bathroom mirror. I’d been trying to figure out how to install it for probably a year and a half or two, but the solution came completely unexpectedly while I was assembling kitchen furniture. That’s when I remembered a line from the movie “Guest from the Future”: “All you need is a push.” I’d considered all sorts of options before that, but came up with this very simple one completely by accident.

That’s why I needed stainless steel slides in the first place. But, unexpectedly, it turned out that either they weren’t available here at all, or they cost completely unreasonable amounts of money. For reference, the ones I found cost anywhere from $60–70 to $100–300 per set, and some were only available by special order.

But when I went to AliExpress, I was surprised all over again. Not only are there a huge number of them, but there’s also a decent choice of sizes at much more reasonable prices.

In the end, I ordered a set for $12.88. The smallest size, 10 inches. There’s also a version with soft-close and one without; I got the one without. For my project, soft-close wasn’t just unnecessary—it would have been inconvenient.

Shipping took a long time, possibly because it coincided with the sales. I placed the order on November 22 and received it in early January.
Inside the package are two slides and a set of mounting hardware.


I had no use for the mounting hardware, but I’ll go into more detail about the slides themselves and how I used them.


I doubt anyone who came to read this review needs an explanation of what full-extension ball-bearing slides are, or how they differ from partial-extension ball-bearing and roller slides. Besides, the photo already answers some of that.


The store page has diagrams to help you choose the right slides, complete with explanations in Russian!



One slide (there are two in the set) weighs almost a quarter of a kilogram. It’s 44 mm wide, 250 mm long when collapsed, and almost 500 mm when extended.


The metal was difficult to measure, but I got about 0.8 mm. The mechanism is almost 13 mm thick overall; the ones sold here are usually around 12.7 mm.
I also found a minor issue: there’s noticeable side-to-side play. In other words, if you push the sliding section to one side or the other, the thickness at the edges varies from 12.27 to 13.63 mm. In this case, it’s an unavoidable trade-off because the section with the ball bearings is short. But if you use them as intended—that is, in furniture—you won’t notice it at all.


The store listed completely different figures for the metal thickness and the overall slide thickness. It didn’t matter at all in my case, but it was still disappointing.


Overall, though, they move very smoothly, and all the moving parts are generously coated with thick grease.



The latch has just the right amount of give. With ordinary slides, the latch can be so tight that I sometimes have to spread the “fork” that locks onto it a little. I liked this one better: it holds securely, but I didn’t have to bend anything.


There’s a plastic stop at the end. Nothing different from ordinary slides here.


One of the linear bearings, with its cage and balls.


The balls are, of course, quite strongly attracted to a magnet. The slide material is magnetic too, but noticeably less so. Someone will probably point out that stainless steel should be nonmagnetic. That’s a common misconception: stainless steel comes in different grades, some magnetic and some nonmagnetic. This one is somewhere in between—a regular magnet barely reacts to it, but a neodymium magnet sticks.


As you can see, I didn’t choose the slide length at random. First, I drew up a scale plan of the area where they would be installed. I used the tile layout drawing I’d made for this bathroom, then overlaid the furniture, the niche, the curtain rod, and so on. After trying out different options, I settled on the slide length and worked out the dimensions for the mirror.


I ordered the mirror from Apex-Mdf, a company in Kharkiv. I think it used to be called Apex-Style. Overall, it turned out to be inexpensive: at 480×780 mm, it cost about 650 UAH ($25). But it took a looong time to make, possibly because of the New Year holidays.
The only thing that surprised them was that I wanted a mirror, not glass in an aluminum frame.


Since this is a bathroom, it gets damp, so to keep everything from rusting, the mirror came in a frame made from aluminum profile. There were several options to choose from, and I picked F1 as a compromise between durability and appearance.


I was a little surprised to notice that the mirror wasn't just installed as is; it had a white protective film on the back. I hope this will extend its service life, since the regular mirror in our home has already been damaged by moisture.


Using the drawings and photos of the installation area, I worked out where to mount the rails on the mirror frame. As it turned out, the end of each rail landed right on the inner part of the frame's flat surface.


The mirror mounting principle is very simple: it hangs on the rails. At first I wanted to screw it to them somehow, but there was a “catch”: I could screw it on, and even install it afterward, but since the rail catches would then be behind the mirror, I wouldn't be able to remove it again.
One option would have been to install the rails “backward”—the narrow side against the wall and the wide side against the mirror—but even then, there was no guarantee it would work.

So I started by preparing the slots for hanging it. To avoid breaking the mirror, I first removed the top section, marked it out, and marked the possible hole locations. I also noted where the steel angle ended so I wouldn't drill into it.


These are the slots I ended up with. I could have bought steel hangers, but I would have had to track them down, and besides, there's no guarantee they would have been any easier to work with.
I cut away the bottom of the top rail so the guide wouldn't stick up.


At first, I planned to drill holes in the rails, tap them M4, and screw bolts into them. Then I would take two M4 nuts and lock them against each other, 2–3 mm from the surface, making pins that would fit into the slots in the mirror frame. But the most I could do was drill the holes, and the thin metal wouldn't hold a strong thread. I also couldn't make a die to deform the metal and give the thread more material, so I had to “try another approach.”

I ground down four M4 nuts on the bench grinder, then threaded them onto the installed bolts, followed by a washer and a regular nut. I ground them down so I wouldn't have to drill larger holes; 6.5 mm was enough. I used nuts to keep things simple, though I could have used some tubing, but I would have had to find some.


I did the same thing with the bottom section, with one difference: the hanger holes were shifted upward, and I drilled a hole for the pin to enter instead of cutting a slot.
Unfortunately, there wasn't enough room to use a step drill, so I had to use a 16 mm hole saw. In the end, not only did I use a whole bunch of tools, I also had to finish it with a needle file :)


It came out pretty neat, but because the hole saw was so large, the hole was an extremely tight fit. The same went for the pilot drill; in the end, I had to remove it altogether so it wouldn't drill right through.


The final preparation step also took a bit of head-scratching. I needed a way to keep the mirror from accidentally coming off the hangers—something secure, but also invisible.
The solution was simple: screw in two bolts from underneath. Their length also factored into calculating where to drill the holes for the hangers.


Everything is prepared and ready to be taken to the installation site.


And here's where it will go. The whole problem was that this turned out to be a very awkward spot for a mirror. The door to the pipe access niche can't be moved, nor can the niche itself, and the same goes for the sink. If the door were farther to the right, I could hang the mirror on the wall; if it were farther left, I could hang it on the door itself. But as it is, it's “neither here nor there.”


After that, it's all standard: marking, drilling, and installing the rails. The only thing was that I had to use long 8×65 mm wall plugs because there’s also drywall between the tile and the brick, as far as I remember.
Before installing the rails, I applied double-sided tape. It makes them easier to install and also makes it harder to crack the tile, since I tightened the screws with quite a bit of force.


The rails are installed.


Then I installed the removable section with the hinge pins. I think it’s now clear why I did everything this way. By the way, in this configuration you can remove them without any trouble, either with some kind of hook to release the latch or simply by unscrewing the screws.


Hang the mirror, and that’s basically it. The final step was almost anticlimactic: I picked up the mirror and simply hung it on the wall. Not very exciting—I didn’t have to adjust anything, trim anything, and so on.
After hanging it, I screwed in two screws at the bottom, so now the mirror can only be removed after unscrewing them.


I chose the installation height so the mirror wouldn’t get in the way of anything, including opening and closing the sink’s drain stopper. And, as usual, there’ll probably be something sitting on the sink itself.
The gap between the mirror and the tile came out to about 15 mm. I was worried it would be very noticeable, but in practice it’s barely visible.


Now, to access the meters and taps, all I have to do is slide the mirror to the left and open the door. When closed, the rails are held in place by catches, so the mirror won’t slide open accidentally.


That brings the penultimate stage to a close. It may not have turned out as aesthetically pleasing as I’d hoped; some things should have been planned from the start, but you can’t think of everything, unfortunately. Still, I now have a solution to this kind of problem, and maybe it’ll come in handy for someone.


The last stage is connecting the intercom, and I’m still “in the process,” even though you’d think it would be straightforward. Turns out it’s not that simple.
What does an ordinary person do when they want to connect an intercom? They call the company that services them and ask for a technician to come out, draw up a contract, and connect it. But things didn’t work that way here.
I found the phone number of the company that installed the building’s intercom, called them, and some time later a technician called me back. We talked, and he said he’d spoken to the building manager, who told him that when the original contract was signed, we hadn’t paid for installing a floor-level switch for this apartment. Well, if that’s the case, I said, just work out the total cost.
He worked it out, called back, and gave me the figure... about $70, of which roughly $30 was for the switch and $40 for the callout and “programming” the switch. And I hadn’t even checked whether that included running the cable (12 meters) and the cable itself.

That price put me off a bit, so I went online to see what kind of switch it was. I know a little about this field, after all. It turned out to be a standard BK-4MV made by Vizit, which costs closer to $20 than $30—so they’d marked that up by 50% too.
Anyway, when I went to hang the mirror, I also checked which switch was installed. There were two possibilities: the old 4MV or the new 4AV, which has a jumper for connecting the video line’s terminating resistor and a ground wire. The new version costs $22; the old one is about $18, but it’s no longer in stock.
I opened the cabinet and saw what I expected: a BK-4MV, with one apartment connected out of four possible, and six apartments on the floor. In any case, I’ll have to install a separate switch.
I asked the building manager about installing it without the “company.” She said that in this case the intercom is common property, so I can buy the switch myself and hire another technician—or install it myself.


What’s more, you can build this kind of switch yourself if you want; the circuit is online. This is a slightly outdated version, but it would work just fine for my needs.


I’m not cheap, of course, but I get a little annoyed when they quote me a fee for “programming” the switch that’s only half the cost of installing, say, an air conditioner, while also marking up the switch itself by 50%. Especially since the “programming” is extremely simple and described in detail in the Russian-language manual. In the end, I arranged with a friend that we’d install it together: he’ll run the cable, and I’ll connect and “program” the switch.
There’s also an adapter here for connecting to a video intercom, but that’s still to come. I might even write it up if anyone’s interested :)


That’s all from me. I hope this was useful.
$12.88
Go to store
This page was found when searching for:
26, 7, направляющие,двигать,двери,на,мебели,из,нерживейки, 1, https://www.kirich.blog/obzory/drugie-obzory/835-teleskopicheskie-napravlyayuschie-polnogo-vydvizheniya-iz-nerzhaveyuschey-stali, 21, направляющие из нержавеющей стали, шариковые направляющие firemax выдерживающие нагрузку 50 кг купить во владивостоке не дорого ., Шариковые направляющие "Firemax" выдерживающие нагрузку 50 кг купить во Владивостоке не дорого ., направляющие полное выдвижение из нержавеющей стали, телескопические направляющие electrolux tr2

Questions and answers

What are the dimensions of the stainless-steel full-extension slides?

Each slide is 250 mm long when closed and almost 500 mm when extended, and is 44 mm wide. One slide weighs almost a quarter of a kilogram.

How do the telescopic slides in the review work?

They move very smoothly, with the moving parts generously coated in viscous grease. The latch holds securely without being too stiff, though there is noticeable side play.

Can these slides be used to hang a bathroom mirror?

The author chose them to hang a mirror because stainless-steel slides were needed. Their length helped determine the mirror dimensions and mounting position.


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister