CPS-6011 Adjustable Power Supply, or Another GOPHERT
$180.44
About a year ago, I did a review of the very interesting and fairly well-made GOPHERT CPS-3205 adjustable power supply. Not long ago, I came across a more powerful version of this PSU. I couldn't resist, so I bought it.
As always, I'll take a look, run some tests, take it apart, and share my conclusions.
First, a note: since I already have a fairly detailed review of the less powerful version, which is very similar to the one covered here, I'll be referring to it often throughout this review.
The design and circuitry are very similar, so this review will follow the same format as the previous one.
Let's start, as usual, with the packaging. There's not much difference from the previous one, apart from the size.
This time, the manufacturer decided not to include its cheap load cables. In my opinion, that was the right call: better no cable at all than one with 0.5 mm² conductors.
So the box contains only:
1. Power supply
2. Manual
3. Power cord.
A few key specs from the manual.
I won't translate everything, but in short: it's a microprocessor-controlled power supply with efficiency up to 90% and ripple of up to 30 mV (peak-to-peak).
The rated output voltage and current are clear from the model name: 60 V, 11 A.
This time, the included power cord is the right kind, with a plug that fits our outlets. These cords are very common, but it's still nice to have one included. The cord is fairly flexible, too.
That's all there is to say about the accessories. Let's move on to the star of the review.
It looks exactly like the previous model, except it's a little larger.
The previous model measured 192 × 120 × 58 mm; the new one measures 265 × 160 × 82 mm, including all protruding parts.
The weight, however, is about the same, which was partly a drawback—but more on that later.
At first glance, the front panel shows a few differences, though they are fairly minor.
The display uses a 4+4 format rather than 4+3 as on the previous model (although that one was also available with this type of display).
There are more significant changes to the controls. The most noticeable is that the power switch is now on the front rather than the back, which is much more convenient.
The Voltage/Current mode selector has been replaced with a button. This is less convenient because the button is quite stiff.
A button and indicator for displaying output power have been added. Pressing the button switches the display from output current to output power. The reading is shown for a few seconds, then the power supply returns to the previous mode. This is why the photo came out so blurry, so it won't be included in the review; I don't see much point in showing it anyway. The display format is _000.
Everything else is the same: the output and control-lock buttons, and the same push-button encoder.
Pressing the encoder selects the corresponding display digit, which is then adjusted. By default, the smallest digit is adjusted; pressing the encoder cycles through the adjustment increments. One advantage is that the power supply remembers the last set value.
There have also been a few changes at the back.
The output terminals are larger, which makes sense: the output current is now 11 A (there is also a 20 A version), up from 5 A. There's also a fan, which is what makes this compact size possible. It's quite noisy, but its speed is automatically controlled by temperature. When switched on, it runs at full speed for a few seconds, then gradually slows to a stop. The control is very sensitive, though, and even a 100 W load makes it run at about 30–40% speed.
There are also some empty spaces, presumably for the remote-sensing terminals and the external/internal regulation mode switch.
The power inlet is combined with the fuse, and there is no input-voltage selector.
The design is familiar by now: a heatsink-style case, even in the same color as before.
The same checkerboard-style feet are on the bottom, but this time the manufacturer placed them less conveniently, closer to the center.
As I mentioned above, the power supply is fairly light. The feet's placement and material cause a couple of problems:
1. Pressing the front or back of the power supply makes it want to tip forward or backward. Moving the feet closer to the front and rear panels fixes this.
2. The buttons are stiff, and since the power supply is light and the feet are slippery, you have to hold it with one hand while operating it, or it just slides across the table. Replacing the feet with rubber ones would help, though I'd also add some weight to the case :)
You can also see the ventilation openings at the front. The cooling system is well designed, with air flowing through the entire case.
1. When switched on, the power supply starts in the Off mode, but you can set it to turn on automatically. To do this, hold down the on/off button and turn the encoder until dON appears (it takes a moment). To switch back, do the same until dOF appears.
2. The maximum output voltage is 63 V, not 60 V as the model name suggests.
3. The maximum output current can be set to 11 A, as specified in the specs.
4. As before, you can lock the controls, and the corresponding indicator lights up.
5. The minimum settings are 0.01 V and 0.01 A.
6. With no load on the output, however, the display reads 0.09 V.
I apologize in advance for the poor photo quality here and throughout the rest of the review. As with the previous model, the film over the display is quite light, and it took some effort to get readings that were legible. Under artificial lighting, there's no problem and everything is easy to see. In bright sunlight (or with the flash), the display becomes washed out and hard to read, so a light filter is needed.
As in the previous review, the first test checks how accurately the output voltage is set with no load. Or rather, with a light load from a 1.5 kΩ resistor.
No complaints here. Up to the maximum output voltage, the difference was no more than 0.07 V, and that only in the middle of the range. I’d call that a good result.
The next standard test measures ripple under load. It also lets us check voltage regulation under load, rather than with no load.
A quick note: I set the maximum load current to 10.5 A because my electronic load doesn’t have a CV mode. Pairing a current regulator with a load operating in the same mode doesn’t end well, so the power supply was set to CV (constant voltage) and the load to CC (constant current).
The test was also limited to 50 V because that’s the maximum voltage for my electronic load.
1. At an output voltage of 5 V and a load current of 10.5 A, ripple was no more than 10 mV. Excellent.
2. This was the only test where ripple exceeded the specified 30 mV, reaching about 37–40 mV.
1. At 20 V and 10.5 A, ripple was about 30 mV, within the specified limit.
2. At 30 V and 10.5 A, the result was the same.
1. At 40 V and 10.5 A, ripple was still 30 mV.
2. At 50 V and 10 A. For this test I reduced the output current because the load is rated for 400 W, and this would have been about 500 W. Ripple was still 30 mV.
I should also note the good voltage regulation: in every test, the output voltage was practically the same as it was with no load.
I ran this test after talking with one of my regular readers. He said that his previous model has elevated ripple at maximum current and low output voltage. That conversation is what prompted me to run another test.
1. Output voltage: 3.3 V; current: 10 A. Ripple is barely distinguishable.
2. Seeing that everything was fine, I made the test more demanding: 2 V and a load current of 10.5 A. Ripple was minimal.
And, as in the previous review, the final test measures the accuracy of the output current reading.
Since the load can’t operate in CV mode (as mentioned above), I tested the power supply’s built-in ammeter against the output current. Since the current setting is based on the same readings, we can consider the test reasonably valid.
As before, the test was run at a mid-range output voltage, which this time was 30 V.
1. Load current: 67 mA. This is the lower threshold at which the power supply displays the output current; at a load current of 60 mA, the display reads 0.
2. Load current: 92 mA (limited by the electronic load’s adjustment resolution).
3. 191 mA
4. 499 mA. So far, so good.
I won't go through everything point by point. In short, as the current increases, the power supply starts to read slightly high, reaching an error of about 0.8% by the end, which is still pretty good.
The test also shows that the power supply maintains a stable output voltage: as the load current changes from 67 mA to 11 A, the output voltage changes by just 0.01 V.
That's the end of the tests. Let's open it up—I was very interested to compare this power supply with the previous one.
The disassembly process is the same as before: I unscrew the rear panel and slide out the bottom.
I really enjoy taking things apart, especially power supplies, so I've hidden the rest of the teardown under a spoiler. There are a lot of photos, even after I went through and picked them out.
Unfortunately, my electronic load is limited to 400 W of continuous power, so I ran the one-hour test at that level only. A new one is still in the works, and it's planned to handle considerably more power, but you make do with what you've got.
At this power level, the power supply's case warmed up to about 35 degrees in roughly 20 minutes, then the temperature stopped rising. The photo shows that the edges of the case are hotter, with more heat coming from the area where the output diodes are located. The test was run at 10 A and 40 V.
The red area to the right of the power supply is the table, warmed by the heat from the electronic load.

At the same time, the air coming out of the power supply is only slightly warmer than the ambient air. At least, the temperature of the table barely changed, which is more than I can say for the load (second overall photo)—everything that could get hot did :)

Before listing the pros and cons, as I did last time, I'll share my personal impressions.
The power switch is a clear improvement. It's much more convenient when it's on the front panel.
The output terminals are noticeably better than last time, but the terminals on my cable don't fit snugly, so I'd use it in the clamping configuration.
Heat: everything is within normal limits. Then again, I had no complaints about this last time either.
Display: the red display was easier to read than the green one, but the lack of a filter spoils the overall look. It was the same last time.
I have exactly the same reservations about the control logic as last time. In my opinion, a second encoder would have been better than using a toggle function.
A quote from the previous review:
The advantage is that in practice you usually adjust only one parameter, so one encoder is enough, and switching between modes is no problem.
The downside is that if the power supply exits adjustment mode, you have to turn the encoder one extra click to get back (switching to display mode for the set parameter); the next click adjusts it.
Also, while adjusting, both displays switch to showing the set value. But there's no getting around that—it's a minor trade-off for the minimalist design.
The most inconvenient thing, though, was that after switching to the output parameter display and then trying to adjust the settings again, the power supply enters adjustment mode with the finest step size.
For example, I was adjusting in tenths of a volt, then let go of the knob and the power supply returned to normal mode. If I then decided to increase or decrease the voltage again, I'd be adjusting in hundredths of a volt—or I'd have to press the encoder. It annoyed me, though I could get used to it. I think the developers could easily have added a memory for the last operating mode; that would have been more convenient.
Pros
Well-thought-out design and fairly high-quality construction.
The circuit design may be “from the '90s,” but it's quite reliable.
Quality components with plenty of headroom.
Ripple is within normal limits (except at 10 V and maximum current).
As I said last time, it's clear they didn't cut many corners, if any.
Output power measurement mode added.
Active power factor correction.
Cons.
Stiff buttons, combined with the low weight, make it harder to operate.
No output fuse.
Active cooling.
The large output capacitor means you shouldn't connect a device under test to the power supply while voltage is present at its output (for example, low-power LEDs and the like). This is a drawback of almost all switching power supplies, though.
My opinion hasn't changed. Like the previous version, this one has decent specs, fairly low ripple even at maximum current, excellent output voltage regulation, and high setting accuracy. The design is still just as well thought out; only two things are disappointing: the stiff buttons and the lack of a display filter.
The sloppy soldering on the control board could also be counted as a drawback, though I'll allow that it may be an isolated case. I did have a few complaints about this last time, too.
In short, it's the same power supply, just a higher-power version: 700 W instead of 160 W, with active power factor correction and active cooling added. The ergonomics have been improved a little by moving the power switch to the front panel, and a wattmeter mode has been added.
I bought this power supply to replace the previous one, which I sold. I used a coupon, since this is a new product in the store, and they gave me a discount as a new-product promotion. The coupon code is Supply; with it, the price is $151. It's valid until November 30.
I can already guess the first question: why do I need it? I have more than one adjustable power supply at home, including one with an output current of 22 A. So I bought this one mainly to satisfy my curiosity about the new GOPHERT power supply series. My curiosity has been fully satisfied. I still don't know what I'll do with this power supply next; everything I learned about it, I've covered and shown in this review.
In any case, I don't regret it. I liked the power supply, even with its drawbacks.
By the way, more powerful versions are available, too.
That's all for now. As always, I look forward to your questions in the comments :)
$180.44
This page was found when searching for:
https://www.kirich.blog/obzory/bloki-pitaniya/216-reguliruemyy-blok-pitaniya-cps-6011-ili-esche-odin-gophert, гоферт, gophert cps 1610 схема, схема gopher cps 6017, блок питания 6010e распаковка, gophert gpc 6011, cps6011, matrix лабораторный блок gopher cps 6011, gophert 1001, gps6011 блок питания thermaltake, gophert cps 6011 инструкция на русском, gophert cps 6011 manual, отзывы gophert cps 1660, cps8706, gophert cps 1610 отзывы, gophert cps-1610 отзывы, gopher 6017 цена, cps 1600, источник питания цифровой cps 1610 для чего нужна, gophert cps 6017 форум, gophert nps-1600 инструкция, gopher cps 6011 инструкция по эксплуатации на русском языке, лабораторный блок питания gophert cps 1001 купить, лабораторный блок питания gophert cps-1001 купить, gophert качество
https://www.kirich.blog/obzory/bloki-pitaniya/216-reguliruemyy-blok-pitaniya-cps-6011-ili-esche-odin-gophert, гоферт, gophert cps 1610 схема, схема gopher cps 6017, блок питания 6010e распаковка, gophert gpc 6011, cps6011, matrix лабораторный блок gopher cps 6011, gophert 1001, gps6011 блок питания thermaltake, gophert cps 6011 инструкция на русском, gophert cps 6011 manual, отзывы gophert cps 1660, cps8706, gophert cps 1610 отзывы, gophert cps-1610 отзывы, gopher 6017 цена, cps 1600, источник питания цифровой cps 1610 для чего нужна, gophert cps 6017 форум, gophert nps-1600 инструкция, gopher cps 6011 инструкция по эксплуатации на русском языке, лабораторный блок питания gophert cps 1001 купить, лабораторный блок питания gophert cps-1001 купить, gophert качество
Questions and answers
What is the maximum output voltage of the GOPHERT CPS-6011?
The author measured a maximum of 63 V, above the 60 V stated in the model name.
What is the maximum current of the GOPHERT CPS-6011?
The output current can be set up to 11 A, as specified.
What drawbacks did the CPS-6011 review find?
The buttons are stiff, and the fan is noisy and starts running at loads of around 100 W. The light unit can also slide on the table when buttons are pressed.
The figures from this review are in the measurement database: Power supplies
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments6
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister





















































Comments are published in their original language.