/       /       /    Worx Cordless Rotary Hammer, or When All You Have Is a Hammer, Everything Looks Like a Nail
Support the project on Patreon


Worx Cordless Rotary Hammer, or When All You Have Is a Hammer, Everything Looks Like a Nail

$152.59
Go to store
I use power tools often, and as it happens, quite a few of them are battery-powered. But this is the first time I’ve tested a cordless rotary hammer, so I’m doubly curious to see what it’s like.
As usual, I’ll take a look, take it apart, and test it.


I already own a rotary hammer, the well-known and popular Makita 2470. I showed it in one of my reviews a while back, and I can say it definitely doesn’t sit around unused.
But the nature of my work means that every now and then I find myself thinking about a cordless version of such a popular tool. Of course, I should say right away that most DIYers get along just fine with corded tools, and will probably wonder why anyone would need a cordless rotary hammer when you can just use an extension cord and get the job done much more cheaply.
I’ll answer that right away: I can think of at least two real-world situations where a corded tool simply isn’t an option:
1. Working far from an outlet, or, as people often say, out in the middle of nowhere. A typical example I ran into just the other day was installing cable in a conduit along a fence with a perimeter of about 160x120 m, with the nearest outlet roughly 70–90 m away. On top of that, various construction workers are constantly moving around the site with their shovels, vehicles, and so on.
2. A room where people are working almost all the time, and which isn’t just damp but practically wet. Power tools are only allowed to be used there when nobody else is around, which means you have to wait. With a cordless tool, that’s not a problem.

There’s also a third, less common use case: drilling a small number of holes in difficult conditions, such as at height—for example, installing security cameras around a building. You could use a regular rotary hammer, but you’d spend ages running around with an extension cord looking for outlets....

Some time ago, I was eyeing the small Bosch Uneo rotary hammer. It’s light and compact, but apart from its low impact energy, it has one major drawback: it uses SDS Quick shank bits instead of the standard SDS+, so you can forget about cheap consumables.


I’d basically given up on this kind of tool once again, when I came across the Work rotary hammer. I was able to get one for review, and this time I couldn’t resist.

I placed the order and, some time later, received a large branded box from the JD store. Inside were a carrying case, a small white box, a manual, and air-filled packing bags for protection.


First off, I’ll point out that it comes with a pretty decent case for storing the rotary hammer, charger, and chuck. For example, my Makita angle grinder didn’t come with a case, so I have to keep it in a cardboard box—although lately the box has been living separately from the grinder. Either way, it’s very inconvenient.


There’s a cardboard insert on top, apparently just for decoration, since the pictures on it don’t tell you much.


There’s another insert at the bottom. It lists the specifications and package contents in several languages (but not Russian).


The actual package contents differ from what’s listed, but more on that later. The specifications are here too, though the only things you can make out are:
Impact energy: 1.5 J
Speed: up to 1100 rpm
Impact rate: 5300 per minute (88 per second)
Power supply: 20 V
Weight: 1.6 kg.

One of the key specifications for a rotary hammer is its impact energy. This one is rated at 1.5 J. For comparison, the Makita 2470 is rated at 2.4 J, with the same rotational speed and a lower impact rate (4500 versus 5300), so the difference isn’t all that great.


Later, I found all the specifications in Russian, but they differ slightly from those listed on the box.
There are also three versions:
WU380.3 — case, rotary hammer, charger, two 20 V 2 Ah batteries.
WU380.2 — case, rotary hammer, charger, one 20 V 2 Ah battery.
WU380.9 — rotary hammer only, without a case, charger, or battery.

The version I got is highlighted.


But there’s actually a little-known fourth package option:
WU380.4 — bag, rotary hammer, charger, one 2 Ah battery, and one 4 Ah battery.

I stumbled across it while watching reviews.


The case was both a pleasant surprise and a disappointment. I liked that it has proper hinges, a comfortable handle, and a compact size, but the latches are quite stiff. Most importantly, it only has room for 2 Ah batteries, even though the tool is compatible with 2, 4, and 6 Ah batteries, and higher-capacity batteries are more useful under heavy load.
That is, You can keep one battery attached to the tool and the other in the dedicated compartment, but the compartment is only big enough for the smallest battery.


So, the complete kit includes:
1. Worx WU380 rotary hammer
2. One 20 (18) V, 2 Ah battery
3. Charger
4. Case
5. Quick-release chuck
6. Two SDS+ drill bits, 6 and 8 mm
7. Two metal drill bits, 4 and 5 mm
8. One drill bit for ceramic tile or similar materials
9. Four screwdriver bits: PZ1, PZ2, PH2, and one flathead bit
10. Two manuals, one for the rotary hammer and one for the charger

It's a very decent kit. The only thing missing is a second battery, but you can buy one separately if needed.


There are two manuals. They followed Milwaukee's approach, where the second manual is for the charger, which makes perfect sense. But the manuals aren't much use: both are in Chinese. Still, I don't think it's difficult to figure things out without them.


Besides the rotary hammer, the kit also includes a chuck and various drill bits.


The drill bits are more of a bonus, since they were even packed separately from the rotary hammer.
3, 4. Two SDS+ drill bits, 6 and 8 mm in diameter. In my experience, these are the most popular sizes.
5. Two regular drill bits, 4 and 5 mm, plus a tile drill bit, 6.5 mm in diameter, with a hex shank.
6. Four screwdriver bits: PZ1, PZ2, PH2, and one flathead bit.

I can't say anything bad about the drill bits. I haven't tested the screwdriver bits, since I doubt anyone would use a rotary hammer as a drill/driver.


The chuck was packed in the case with the tool and is part of the standard kit.


The chuck is quick-release and has an SDS+ shank, just like the drill bits. There's a screw inside for replacing the chuck, but I couldn't undo it, even though I applied a lot of force.
This chuck can hold drill bits from 0.8 to 10 mm in diameter. I can't vouch for the 0.8 mm minimum, but a maximum diameter of 13 mm would definitely have looked better.


A charger is also included. It's very light, though that's not surprising since practically all chargers these days use a switching power supply.


All the status indication is handled by a single LED. It flashes green while charging and stays on continuously once charging is complete. I never saw it light up red.
The stated charging time for the 2 Ah battery is one hour. In practice, it took about that long, give or take a couple of minutes. So 4 and 6 Ah batteries should take around 2 and 3 hours to charge. The charger barely gets warm during use.
The battery connects via four contacts.


Naturally, I took the charger apart. It's very easy to do; all you need is a screwdriver with a hex tip that has a hole in the center.


I didn't look into why the battery has four wires, but they all connect to the charger. I assume two are power terminals, one is for temperature monitoring, and the last one is for some kind of service function.


The rest of the teardown is hidden under a spoiler, since I got a little carried away with the number of photos.


Putting it back together and charging the battery.



Now we get to the actual subject of this review.


In terms of size, this rotary hammer is roughly comparable to Milwaukee's cordless hammer drill. The shape is noticeably different because the Worx's motor is below the chuck rather than in line with it, but the overall size isn't much different.


One description listed the weight as 1.5 kg, another as 1.6 kg, but the actual figures don't really match either of those:
1. The bare tool weighs 1.36 kg
2. With the battery, it weighs 1.76 kg
3. The chuck is heavy, over 200 g, which is a good thing
4. The complete tool with battery and chuck weighs just 3 g under 2 kg.

As you can see, there's no sign of either 1.5 or 1.6 kg here. The actual weight is about 1.76 kg, which is even better for a rotary hammer.


My first impression when I picked it up was that it's compact—not just compact, but also very comfortable to hold. The balance with a 2 Ah battery is good. I think it'll be about the same with a 4 Ah battery, but I can't say about a 6 Ah one; with light drill bits, it might become rear-heavy.


1. The trigger controls power and speed. The handle is coated with a thin, slightly soft material.
2. The forward/reverse switch is on top. In the middle position, it locks the trigger.
3. The third control is the mode selector: drilling or hammer drilling. It has a lock to prevent accidental switching. To change modes, you first have to press the lower part (in this position).
4. There are air outlets at the bottom of the motor. In forward rotation, air blows out toward the front; in reverse, it blows toward your hand. The motor doesn't get particularly hot during use.
5. There are holes on both sides near the battery for attaching hooks—for example, to hang the tool from your belt or hold an unused bit. The hooks themselves aren't included. Interestingly, Milwaukee does exactly the same thing.
6. There's a place to attach a wrist strap at the bottom rear, but that wasn't included either.

As you've probably noticed, there aren't many controls. There's no speed selector like on a drill/driver, and no torque limiter either. That's exactly why I wouldn't recommend using it as a drill/driver: there's a good chance of stripping the screw head—or breaking the bit.
The rotary hammer does have a protective ratchet, of course, but it's only there for protection and is set to a fairly high torque. Mine only kicked in occasionally when drilling wood with a 35 mm Forstner bit.


The chuck, sometimes called the barrel on rotary hammers, looks to have the same design and locking mechanism as any other tool that takes SDS shank bits. Insert the bit with a slight twist until it seats. To remove it, first pull back the part of the chuck sleeve closest to you.


There's a rubber seal inside, and the bit fits very snugly. I'll compare this rotary hammer with a Makita again: with that one, the bit moves very freely after insertion until you press it against the wall, but the hammer mechanism doesn't engage. This one doesn't work that way—the hammer action starts immediately, and the bit itself barely moves relative to the front of the tool. So I expect the seal to last a long time. The seal is needed when drilling overhead, to keep debris from falling into the chuck, which would otherwise be bad for it.


When installed, the chuck partly covers the plastic section of the barrel. It's easy to install and remove, even with one hand. But it's a two-sleeve chuck, and the mechanism doesn't lock the spindle, so you'll still need both hands to tighten a bit.
The chuck is tight out of the box, with practically no play. But based on my experience with a Makita (someone else's in this case; I don't have a chuck for mine), it will loosen up over time anyway.


There's an LED to light the work area. It works well and shines where it should. You can also turn it on without starting the motor by pressing the trigger lightly. But there's no delay before it switches off. Milwaukee spoiled me with that feature, so I'll be modifying this one.


There are no dials or switches on the right side, just a nameplate with a few specs. The only things that are clear are the battery voltage and rotational speed.


Unlike the charger, the battery connection here has three contacts. The fourth contact is clearly only used when charging. The battery fits snugly with no play, and is easy to remove and install—actually a little easier than on the Milwaukee.


And of course, I had to see what was inside. They really went to town with the screws, and they’re pretty tight too, so it’s best to take it apart with a power screwdriver.
They clearly didn’t skimp on the grease either.


Taking the rotary hammer apart isn’t actually that easy. First you have to literally pry off the front part of the “chuck”—it’s rubber—then remove the retaining washer, and only then can you remove most of the “chuck.” You can’t take it apart without doing these steps.


Everything inside is compact and, in a way, even simple, but the difference from the familiar mechanics of a drill/driver is obvious even at a glance. The difference is that this doesn’t use the usual planetary gearbox. In fact, the design is not particularly different from corded rotary hammers that work on the same principle.


The control switch has a heatsink. Maximum current is 25.1 A, voltage is 24 V. The heatsink gets a little warm during operation.


The motor is connected through a small interference-suppression filter.


As with my Milwaukee, it has a motor with four brushes. This is because of the high current flowing through the windings, which is noticeably higher than in most drill/drivers.


The motor itself is wound with wire of a very respectable gauge, too.


Gearbox with impact mechanism.


The rotary hammer barrel—sometimes called the chuck, though I’m more used to the first term, since the bit isn’t clamped in it; it’s simply inserted and held in place by a spring-loaded ball.


Depending on the position of the mode selector, the lower part of the mechanism moves, which in turn engages or disengages the drive to the “wobble bearing.”
The impact mechanism is off on the left and on on the right.


The design is essentially the same as that of its “full-size” counterparts. The only difference is that their motor is usually on the same axis as the drill bit, while here the motor is angled. But don’t confuse this design with so-called “barrel” rotary hammers: those have a crank-and-connecting-rod assembly in the impact mechanism, while this one uses a “wobble” bearing. There used to be rotary hammers where a powerful electromagnet delivered the impact, but they’re no longer made.


As the motor shaft (5) rotates, it turns the “wobble” bearing (1), which moves the piston (2). The piston in turn drives the ram (3), which is connected to the striker (4) that hits the end of the drill bit.
There’s another gear visible underneath, which transmits torque to the drill bit.


The whole process in motion.


And without impact



And last but not least, the tool’s battery.
This is the smallest model, with a capacity of 2 Ah and a stated voltage of 20 V, although 18 V would be a more accurate figure for the actual voltage. Incidentally, the capacity in watt-hours is given for 18 V (18 × 2 = 36 Wh).
There’s a charge indicator on the end, consisting of three LEDs. Press the button to activate it; it stays lit while you hold the button down.


I took the battery apart too, and its design vaguely reminded me of the battery pack from my Milwaukee, though mine are 1.5 and 2.0 Ah.

Batteries with capacities of 2, 4, 6, and apparently 5 Ah are available, but the higher-capacity ones are quite expensive—about as much as the branded DeWalt, Milwaukee, and Hilti batteries.


Inside are five 2 Ah cells made by Samsung—datasheet. It's very strange that the manufacturer chose these batteries, since there's a higher-capacity option, the 25R, rated at 2500 mAh rather than 2000 mAh, with the same discharge current characteristics.


The battery pack is a kind of cassette, already enclosed in a common housing.



An indicator board is mounted on the end. It's coated with protective varnish on top and sealant underneath, while the wires are routed through special grooves so they don't get pinched.


As far as I can tell, there's no cell balancer here. The electronics are covered with a substantial layer of sealant, so I got the impression that protection against over-discharge is handled by the tool's electronics, not the battery pack, although you can make out some components on the board.


I still plan to work on the backlight shutoff delay, but I added a delay to the charge-level indicator right away by installing a pair of 3.3 µF capacitors in parallel with the button. After that, I applied another coat of varnish to the board.


Just to be safe, I measured the battery capacity. First, I charged it with the supplied charger, then discharged it and charged it again using an electronic load.


I discharged the battery to 2.5 V per cell and got 1912 mAh, or 35.15 Wh. The subsequent charge took 2062 mAh. In this case, I suspect the original charger doesn't fully charge the battery, since charging with the electronic load took 2.062 Ah, and the actual capacity of lithium batteries tends to differ only slightly from the rated capacity.


The protection never cut in; the battery discharged normally down to 12.5 V, or 2.5 V per cell.



Since a static demonstration isn't particularly useful, here's the video version of the review, showing it drilling wood, brick, and concrete.
The demonstration itself starts at 8:44, so if that's all you're interested in, you can skip the introduction.
I should clarify something here: at the end of the concrete drilling test, the video shows the drilling speed and time. After making the video, I realized I'd made a major mistake during the test. When drilling, the hammer drill knocks some concrete off the back of the wall, making it slightly thinner, which skews the results for the next drill bits. In practice, the most accurate results were for the first and last bits.
Even so, the hammer drill is quite fast and comes close to matching its corded counterparts.


In the video review, I mention that the 10 and 12 mm drill bits are old, which significantly increased their drilling time. As promised, here are photos of those bits.
The 10 and 12 mm bits are on the left; the supplied ones after testing are on the right.


For comparison, here's the same wall drilled with a Milwaukee hammer drill - review.


And here's a photo with a 16 mm bit. The specs list a maximum of 18 mm, but I didn't have one that size at home.


A few words about estimating runtime. The results aren't great.
I didn't run a full runtime test because I didn't want to scare the neighbors, but I can give a rough estimate. After each of the first and second parts of the test, I fully charged the battery and timed how long it took to restore the charge. I wanted to measure the capacity used to recharge it, but for some unknown reason the electronic load wouldn't top up the battery, so the result is approximate.
First test: six 10 mm through-holes in a 50 mm-thick board, plus two nearly through 35 mm holes, plus two through-holes in a sand-lime brick. Recharging took 15–17 minutes.
Second test: five through-holes in a concrete wall using 6, 8, 10, 12, and 16 mm bits. Total drilling time was about 1 minute 40 seconds, and a full recharge took 25 minutes.

In the video, I said the battery was 25–30% and 40–45% discharged after the tests. That estimate isn't quite accurate, since the charger spends the last 5 minutes or so charging at a low current. In practice, recharging took closer to 10–12 and 20 minutes. So, for the concrete test, the battery discharged by about 33% in 1 minute 40 seconds, or 100% in 5.5–6 minutes of actual drilling.
Drilling a 75 mm-thick wall all the way through (as shown in the video) with 6–8 mm bits takes about 10 seconds, so the battery should last for at least 30–36 such holes. But in the video I was drilling with a 16 mm bit, and not only does each hole take longer, the load while drilling is also much more noticeable. So I’d estimate the runtime at around 35–40 through-holes with 6–8 mm bits, or 60–65 holes 40 mm deep.

Yes, that’s not much. It’s better to have two batteries and swap them out, or use a 4–6 Ah battery. But the calculation showed that the rotary hammer’s actual power is around 300–360 W, based on the battery capacity, its voltage, and the runtime (i.e. the current draw). The Makita 2470 is rated at up to 780 W, roughly twice as much.


And now, the conclusions.
The rotary hammer itself works perfectly well. It drills without any problems through anything short of a load-bearing wall, and certainly through interior walls—although I still don’t know where to find heavy concrete walls in the middle of nowhere. In fact, the rotary hammer is heading off to its first job in just a few days, where it’ll be used to install a pipe along a fence over 550 m long. The plan is to drill as many holes as the battery will allow, then put it on charge and attach the pipe while it’s charging. Fortunately, a full charge doesn’t take that long. In any case, a corded tool wouldn’t be much use there, and an impact drill wouldn’t last long enough.

I’d point out two drawbacks: the capacity of the included battery and the rather inconvenient case, which can’t fit a battery larger than 2 Ah. I could probably also complain that there’s no room in the case to store drill bits, but I think I’ve already found a workaround for that.

Overall, a cordless rotary hammer isn’t really necessary for most jobs, but when you do need one, it’s hard to find a substitute, and it can really save the day.


That’s all. I hope you found the review useful, and as always, I’m looking forward to your questions and comments. The current price is $152.59, and there seems to be a $5 coupon available.
$152.59
Go to store
This page was found when searching for:
конструкция цилиндра и поршня на ручном перфораторе, как работает перфоратор принцип действия, схема китайского аккумуляторного перфоратора bosch, перфоратор toua dblh180 как разобрать и смазать, ремонт качающегося подшипника перфоратора, не работает удар на перфораторе перфоратор причина, перфоратор с поперечным двигателем устройство ударного механизма, устройство перфоратора, иллюстрация механизма осевого удара в ударном шуруповерте, разобрал перфоратор теперь работает только на ударном режиме, как снять патрон с перфоратора worx, устройство перфоратора анимация, как вставить сверло в перфоратор, разборка китайского аккумуляторного перфоратора, www.kirich.blog, 5, 1, 6, https://www.kirich.blog/obzory/instrumenty/654-akkumulyatornyy-perforator-worx-ili-kogda-pod-rukoy-net-nichego-krome-molotka-vse-vokrug-kazhetsya-gvozdyami, 2, перфоратор worx 12 volt, 3, подходят ли зеленые аккумуляторы worx к оранжевому инструменту, bosch uneo, аккумуляторный перфоратор worx обзор, инструмент Worx, перфоратор Worx, аккумуляторный перфоратор, перфоратор на аккумуляторе, аккумуляторный инструмент

Questions and answers

How many holes can the Worx WU380 drill on one battery?

The author estimates about 35–40 through-holes with 6–8 mm bits, or 60–65 holes 40 mm deep.

What are the stated specifications of the Worx WU380?

The listed figures are 1.5 J impact energy, 20 V, up to 1100 rpm, up to 5300 impacts per minute, and a weight of 1.6 kg.

When does the author find the cordless Worx WU380 useful?

It can help when working far from an outlet, such as installing cable along a fence, or in wet rooms where corded tools cannot be used. The author says a corded rotary hammer is enough for most ordinary home jobs.

The figures from this review are in the measurement database: Tools

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments16

Comments are published in their original language.

  1. Иван
    20 October 2019 16:02#1
    Очень хороший  обзор, спасибо большое  для меня  информация  оказалось  очень  полезной! 
    0
  2. 30 November 2019 10:40#2
    kirich:
    2. Помещение в котором почти постоянно работают люди, но при этом это помещение не просто влажное, а можно сказать что мокрое. Работать электроинструментов в таком помещении разрешают только если в нем никого больше нет, а значит надо ждать.

    Это монтаж видеонаблюдения в бане, что ли?  blush 
    --------------------
    Не шалю, никого не трогаю, починяю примус ....
    0
    1. 1 December 2019 11:59#3
      Не, на мясокомбинате.
      0
  3. 27 August 2021 13:25#4
    Как он через 2 года?
    Сейчас можно по акции купить WORX WX390 за 5000 руб.
    Думаю брать или не брать.
    0
    1. 5 September 2021 01:44#5
      Пользуюсь нечасто, но в общем доволен.
      Сейчас вот хочу их аккумуляторную циркулярку купить, сразу в комплекте с 4Ач батареей, будет и для циркулярки и для перфоратора.
      Изначально хотел только циркулярку, а аккумулятор потом, но когда увидел что практически все батареи Worx что продают на Али подделки, передумал.
      0
  4. 5 September 2021 09:38#6
    Заказал вариант перфоратора попроще WORX WX390 (5490 руб.)
    Механика думаю, что та же, но двигатель “шуруповерточный”

    Так же купил:
    УШМ WX800.9 (5090 руб.)
    Пилу дисковую WX530 (8955 руб.)
    Прожектор WX026.9 (3085 руб.)
    Аккумулятор WA3553.3 20V 4Ah (5045 руб.)

    Дня через 4 приедет. Все купил в Москве у официальных дилеров, с гарантией и чеком.
    Плюс/минус - это “китайская” цена на Али.

    Наиболее выгодный вариант – это заказать на ТАОБАО.
    Например, более новая модель перфоратора, с бесщеточным двигателем и амортизатором стоит 600 RMB. С учетом доставки в Россию получится что-то около 110$
    Доставка из Китая сейчас стоит примерно 300 руб. за 1 кг, курс 10 руб. за 1 RMB + 5% услуги посредника.

    На TMALL есть флагманский магазин KRESS, тот же WORX https://kress.tmall.com/
    Там часто бывают акции. Например, по акции бесщеточная УШМ KRESS KU800 стоит всего 379 RMB, с доставкой выйдет тысяч 6. Если комплектом зарядка + аккумуляторы, то 769RMB (11700 руб.) В России такой набор немного дороже https://bit.ly/3BJodkp

    Вообще в Китае есть более авторитетный производитель DEVON https://devon.tmall.com/
    DEVON классифицируется как промышленный. Стоит дороже. В США, Европе и России он продается под торговой маркой FLEX https://www.flex-tools.com/ru-ru/

    Если опасаетесь подделок, то всегда можно купить во флагманском магазине на TMALL. Но там, конечно, как правило дороже.

    Если вдруг интересно погрузится в китайский мир инструмента:
    Обзорщик из Гонконга https://www.youtube.com/c/MASTERALLEY/videos
    Его же блог на местной платформе https://www.ixigua.com/home/3768758033715891/
    Местное сообщество https://www.mydigit.cn/forum-71-1.html
    Местное сообщество https://search.smzdm.com/?c=post&s=DEVON&v=b
    Аналогично https://www.ixigua.com/
    0
    1. 6 September 2021 03:42#7
      Я нашел комплект пила WU533, батарея 4Ач, сумка и прочая мелочь, на таобао, на Али дорого получается, а у нас по моему особо никто и не продает.
       
      0
  5. 7 September 2021 22:30#8
    На складах в России только "желтые" версии. А зеленые бесщеточные практически не продают.
    Туша WU533 стоит 530RMB
    0
    1. 7 September 2021 22:51#9
      Не, я по старинке, с Тао :)
      У нас в Украине нет никаких, ни зеленых, ни желтых, да и вообще к сожалению почти отсутствует такое понятие - отправка со склада в Украине :(
      0
  6. 8 September 2021 00:46#10
    Почти все крупные китайские поставщики переехали на склады в Москве.
    Для меня заказ на АлиЭкспресс - это почти всегда отправка из России с доставкой в течение недели.
    В России АлиЭкспресс - это российская компания  ООО "АЛИБАБА.КОМ (РУ)"
    https://companies.rbc.ru/id/1157746446747-ooo-alibabakom-ru/
    https://www.rusprofile.ru/id/7673224
    У меня магазин на АлиЭкспрессее. Я зарегистрирован как продавец.

    Но многие вещи выгоднее купить в Китае на ТАОБАО. Тот же инструмент, например. Но ждать долго.
    0
    1. 8 September 2021 00:57#11
      Увы, у нас такое практически не встречается, к примеру осциллограф покупал со склада в Украине, но это было редкое исключение, сам был удивлен.
      А так да, мелочевку проще купить на Али, что-то чуть подороже, уже на Тао.
      0
  7. 8 September 2021 09:05#12
    Доставка с ТАОБАО постепенно теряет смысл. Карго из Китая стоит от 5 до 15$ за 1 кг. Плюс расходы на страховку, посредника и т.п.
    Китайские продавцы, завозят и таможат товары контейнерами дешевле 1$ за кг. При этом доставка по России субсидируется. Доставка по России через логистику ЦАЙНЯО стоит менее 1,5$.

    Таким образом, все издержки на доставку перфоратора весом 3 кг от фабрики до дверей покупателя обойдется в 4-5$. Самостоятельная покупка на ТАОБАО раза в 3-4 дороже.
    0
    1. 8 September 2021 10:58#13
      У нас Мист возит по моему по 6-8 долларов за 1кг (заказы делаю не я) до ближайшего отделения, ну плюс еще стандартная пересылка по Китаю, иногда платная, иногда бесплатная.

      Вы не забывайте, что у России есть граница с Китаем, у нас нет, соответственно и расценки на "контейнерную перевозку" могут быть разными.

      0
      1. 10 September 2021 09:46#14
        Вы не забывайте, что у России есть граница с Китаем, у нас нет
         Это часто не имеет значения. Посылки, например, в Сибирь везут через "Москву".
         То есть юридически и фактически посылки едут по маршруту Китай-Москва-Сибирь. И расстояние от Москвы обратно до Сибири просто огромное и больше чем до Украины. Хотя расстояние Сибирь-Китай совсем небольшое (зависит от региона Сибири). Так устроена логистика.
        0
      2. 13 September 2021 09:57#15
        Mist не самый лучший и не самый быстрый вариант. На ТАОБАО форуме есть посредники, которые доставляют дешевле и быстрее.
        0
        1. 13 September 2021 10:11#16
          Здесь следует разделять, Мист Украина или Мист Россия, хоть это и одна и та же компания, но цены/сроки могут заметно отличаться.
          Насколько мне известно, у нас Мист возит по 6-8 долларов за 1кг.
          0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister