/       /       /       /    Various products for electronics hobbyists and more, part 15
Support the project on Patreon


Various products for electronics hobbyists and more, part 15

$1.30
Go to store
Today's roundup is about materials and tools for assembling battery packs, though I may add a few other things as well.

As a reminder, to stay up to date with new posts on the blog, I recommend following me on Instagram. I'll post notifications about all new posts there, and might also write about something interesting now and then - link to account

Most of what I'll show is used for building large battery packs, but there's nothing to stop you using it for smaller builds too, for example, power tools. By the way, I have a calculator for calculating battery packs.

I'll start with various strips, which can be roughly divided into several types:
1. By material
Nickel-plated steel: easy to weld and cheaper, but prone to corrosion and has higher resistance.
Pure nickel: I haven't seen it rust. It's not exactly cheap, has lower resistance, but is harder to weld.
Copper: it only appeared on the market fairly recently. It's even harder to weld and expensive, but has the lowest resistance and doesn't corrode.

2. By shape
Strips in various widths and thicknesses. Choose what suits the job, but it's better to go thicker and wider if you can :)
A wide strip for several batteries at once. It's fairly expensive and not always convenient, but can be a real help sometimes.
Pre-formed contact strips for 2, 3, or 4 cells. They let you build packs with minimal waste and are usually sold in lots of 50 or 100.

Some useful accessories and tools:
1. Holders that make it easier to spot-weld batteries without cell holders.
2. Cell holders make assembly easier and maintain spacing between cells, but cost extra.
3. Adhesive-backed electrical cardboard insulators, available for the positive end or in general-purpose shapes.
4. Spacers to keep cells apart in a battery pack. They're needed to prevent short circuits if the cell insulation is damaged.

Next, I'll post links to listings that I think might be interesting. When choosing them, I picked ones with lots of orders and reviews, but it's best to double-check, since sellers sometimes change things on the fly...

Of course, I'll start with a link to my review of nickel strips, where I tested their quality. I can also say that I've ordered from this seller several times, and the only downside is that they sell by the kilogram.

Nickel-plated steel, lots of orders and positive reviews, 10 m long, 5 and 8 mm wide, 0.1-0.2 mm thick - link


Also nickel-plated steel, with a relatively high number of orders, sold in 10 m lengths. This strip is only one thickness (0.1 mm), but comes in different widths, from 3 to 10 mm - link.
A good choice for building battery packs with low discharge currents.


Pure nickel strip, 8 mm wide, 5 m long, with several thickness options from 0.1 to 0.2 mm - link.


Lately, I'm also seeing more and more listings for wide strips. The Chinese sellers usually call them "belts". They're the same thickness as the narrow strips, but up to 45 mm wide - link to nickel-plated steel strip.


Strips of nickel-plated steel. Personally, I think they're a questionable option because there could be a lot of waste, but why not - link and another one


A couple of wide-strip options, advertised as pure nickel.
The first comes in one width, for 2P packs, and is 0.15 mm thick, but is available in different lengths (2, 5, and 10 m) - link
The second is more complicated: two thickness options, but more interestingly, it's available not only for 2P packs, but also for 3P and even 4P - link.


Pre-formed nickel plates (that's what they're advertised as, anyway) for small packs, for example, power tools. Here are three listings:
1. Thin strips for 3-4 cells - link.
2. Pre-formed strips, which are usually included in housing + circuit board kits, but can also be useful on their own, especially when repairing these batteries - link, but the price is astronomical :(
3. Some more thin strips, but this listing has more buyers, so I think these are probably more useful - link.


As I mentioned at the beginning, copper strips are available too, but in my opinion those are really only for perfectionists - link :)


I won't mention the small holders; I've shown them many times. But here's an option for larger battery packs - link


There are various fixtures to make assembling battery packs easier, but they all do the same thing: hold the pack in place while it's being spot-welded. If you have a 3D printer, it's easier to print your own version.
1. A universal option that works with almost all types of battery packs - link and another one.
2. An option for 2-pack assemblies - link
3. An option for single-pack assemblies - link


An unusual option with built-in magnets. In theory, it should make the job easier, but I haven't tried it, so I can't say for sure - link.


Fish paper is most commonly sold as tape or as die-cut rings for cylindrical cells. You should always use it to insulate the positive terminal, since the tape can easily melt through the heat-shrink tubing.
1. In tape form - link
2. As rings for the positive terminal - link


In some cases, though, group ring insulators are more convenient, especially if you're assembling large battery packs - link.


That seems to be everything for now. I—and I think the other readers too—would appreciate links to similar products that you've tried and can recommend. I also couldn't find battery spacers on AliExpress.
$1.30
Go to store

Questions and answers

Which strips are suitable for assembling battery packs?

The article compares nickel-plated steel, pure nickel and copper. Steel is cheaper and easier to weld, pure nickel has lower resistance, and copper has the lowest resistance but costs more and is harder to weld.

What tools are useful for assembling a battery pack?

Useful items include welding fixtures, cell holders, insulating-paper insulators and spacers. They help secure the pack, maintain spacing between cells and reduce the risk of a short circuit if cell insulation is damaged.

Why use insulators on a battery cell’s positive terminal?

Insulators made from electrical insulating paper protect the positive terminal. The author warns that the strip can melt through the heat-shrink sleeve, so this insulation should be used.


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister