/       /       /       /    A good discount on the DL24MP electronic load
Support the project on Patreon


A good discount on the DL24MP electronic load

$23.16
Go to store
We all know that sellers often pull a fast one during sales, but sometimes there are genuine discounts. Since I know the prices of some products pretty well, I can tell right away whether a discount is real. Anyway, if you’ve been looking for a DL24MP electronic load at a good price, this is the place to go.

To stay up to date with new posts on the blog, I recommend following me on Instagram. I’ll post notifications about every new post there, and might also write about something interesting from time to time: link to my account

You can also subscribe to updates and new articles on the Telegram channel - https://t.me/KirichBlog


First, this electronic load is sold in two official stores, Atorch and Hidance. Both are official stores, and you can even see in the screenshot that the Hidance store, which the link takes you to, uses an image with the Atorch name on it.
I should point out that this load is always $5 more expensive in the Atorch store, though there are also products that are cheaper at Atorch than at Hidance.

So, it currently costs $23.16 when you use coins, and you can get it even cheaper with coupons. You’re unlikely to find a better price.


But I didn’t write this post just to share the discount. I order these loads very often, so I notice the differences and little details.
I ordered some just recently, though only a couple of them.


Here’s the first detail: I’d seen this in this store before, and it’s turned up again. The manufacturer usually uses a ribbon cable to connect the power board to the controller, but this one has separate wires. I can say for sure that if you use the load outside a fixed installation—in other words, not mounted in an enclosure—the wired version is definitely more reliable.


The second detail showed up in a load I bought for the first time. They used to install IRFP264 transistors. I can’t say whether they were genuine, but these transistors don’t have a safe operating area graph for linear operation. Yes, they’re used well within their limits here—four of them for 150 W—which is great. But experience shows that even in this configuration, reliability depends heavily on voltage and temperature.


Recently, someone asked me for help after burning out their regular DL24, which has a single transistor. It had a CS50N20, and I was surprised at the time.
But both of my last two orders came with boards that also use CS50N20s. These transistors are more interesting, though a little unusual.




A quick search turns up a datasheet for this transistor in a TO-220 package, but if you dig around the internet a little more, you can also find a datasheet for the TO-247 version.


The important thing they have in common is that both have a DC region on their SoA graphs. Yes, you can forget about the 200 V mentioned in the load’s description. The transistors are rated for 200 V, but I definitely wouldn’t use them in linear mode anywhere near the upper voltage limit. I’d stick to 100 V.
By the way, these transistors are also sold on AliExpress by themselves: link

Note. Of course, nobody can guarantee that you’ll get a load with wires and these transistors too, but the chances are very good. My two recent orders show that, and loads with wires have occasionally arrived from this store before, while I’ve never seen one from the Atorch store.



If you want to increase the power, the store has two power board options: one for the DL24MP/DL24EW and one for the DL24M. As far as I can tell, they’re not compatible. Since the DL24M doesn’t seem to be sold anymore, go with the first option: link.
By the way, I have three of these boards for the DL24MP at home. If anyone needs one, I can sell it at a good price.

One more thing: the original switching boards for the DL24EW are pretty much useless. They’re only worth buying if you’re planning to charge at a very low current, say up to 5 A. And even then, their design is pretty poor.



I may add some good deals on other products from this company later, if any come up. For now, that’s about it. Hope you found this useful.
$23.16
Go to store
This page was found when searching for:
1

Questions and answers

How much does the DL24MP cost with the discount?

According to the article, it costs $23.16 when using coins; coupons may reduce the price further.

Which transistors may be fitted in the DL24MP, and what voltage does the author recommend?

The boards in two recent orders had CS50N20 transistors. Although the transistors are rated for 200 V, the author recommends limiting voltage to 100 V in linear operation.

How do DL24MP versions with wires differ from those with a ribbon cable?

The wires connect the power board to the controller instead of a ribbon cable. The author considers the wired version more reliable when the load is used outside a fixed installation.

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments11

Comments are published in their original language.

  1. 21 November 2024 23:53#1
    Сегодня получил заказанную 11.11 нагрузку. Таки да, приехала с соединением сделанным проводами, а не шлейфом
    +2
    1. 22 November 2024 12:50#2
      Спасибо за комментарий, а транзисторы как на фотке у меня или старые IRFP264?
      +1
      1. 22 November 2024 13:32#3
        CS50N20, тоесть как у Вас
        +2
  2. 24 November 2024 23:11#4
    Тоже получил с проводами и CS50N20

    Попутно вопросы, если будет время ответьте, пожалуйста:
    1) Сравнивая со старой версией (https://www.kirich.blog/obzory/izmeritelnoe/1230-horoshaya-cena-na-nagruzku-dl
    24mp-i-ee-ekspress-obzor.html)  заметил отсутствие диода и резистора справа от надписи "input" (левый нижний угол). Это хорошо/плохо/без разницы?
    2) из обзора старой версии
     "...на плате появился третий резистор на 2мОм... Рекомендую увеличить номинал этого резистора хотя бы раз в 100."
    x100 оптимально? на что повлияет?
    0
    1. 27 November 2024 03:39#5
      1. Это просто добавляет неудобств, потому как с ним можно не ставить перемычку между А+ и V+ если используется двухпроводное подключение
      2. Видимо из-за неаккуратного использования при применении с четырехпроводным подключением часто палили входной АЦП, потому разработчики превратили четырехпроводное подключение в трехпроводное, потому как резистор на 2мОм почти то же самое что ноль. В итоге измерительный провод V- превратился в силовой. Если увеличить номинал резистора, то начнет работать четырепроводное подключение, если оно не сильно критично, можно оставить как  есть.

      +1
  3. 25 December 2024 13:58#6
    Вышла новая версия нагрузки BW150 WiFi Tuya 150W 25A 4-Wires Battery Load Capacity Meter Battery Smart Electronic Charger Discharge USB Resistance Teste
    https://vi.aliexpress.com/item/1005008237096946.html
    Что можно сказать про нее по описанию и фото?
    0
    1. 25 December 2024 14:11#7
      Пока скорее всего это та же CL24, неделю назад заказал, жду.
      0
  4. 25 February 2025 20:49#8
    Доброго времени суток. Помогите идентифицировать моего "франкинштейна". Приобрёл на Али в этом году как DL24, работает, в принципе устраивает. Вопрос как обновлять прошивки(при случае) так как модель мне не понятна. Плата как у BW150, интерфейс точно DL24, на телефоне подключился как DL24_SPP(гугл ответа не даёт), версия прошивки 1.0.5 По какой модели этому чуду искать прошивку? К сожалению только одна фотка влезла( 
    0
  5. 7 June 2025 02:29#9
     Вопрос такого плана. Когда измерял мощность понижающего модуля , пока подключал случайно провод торкнулся нижней части нагрузки DL24MP-FX 150W и она потухла, что  там коротнуло, без понятия. Но разобрав и методом тыка выявил не исправную деталь, которая была закорочена. И вот проблема , я не знаю что это за деталь, может Вы подскажите? У вас на плате на ней написано 43, а у меня 169 / 250.  
    0
    1. 7 June 2025 03:43#10
      Это коммутатор, я покупал здесь  - ссылка.
      +2
      1. 7 June 2025 14:46#11
        Спасибо большое.
        0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister