/       /       /    Beelink Gemini X45 Premium with a Celeron J4105 processor, 6 GB of RAM and a 128 GB SSD
Support the project on Patreon


Beelink Gemini X45 Premium with a Celeron J4105 processor, 6 GB of RAM and a 128 GB SSD

$198.99
Go to store
It wasn’t all that long ago that computers with Gemini Lake (SoC) processors started appearing on the market (I’ve already covered one), and other manufacturers soon followed with their own models. Today I’m taking a look at one of them. Its key differences are 6 GB of RAM and an SSD rather than eMMC flash storage, along with a few other minor details.
As always, I’ll take a look inside, tear it down, run some tests, and share my conclusions.


I’ve been asked about this computer model several times, so I really hope this review will be useful.
First, a quick note about the configurations this computer is available in.

First up, the X45:
1. Intel Gemini Lake Celeron J4105 / Intel UHD Graphics 600 / 4GB DDR4 + 64GB mSATA SSD - $189.99 - link
2. Intel Gemini Lake Celeron J4105 / Intel UHD Graphics 600 / 6GB DDR4 + 128GB mSATA SSD - $198.99 - link

There’s also a model with a more powerful processor and 8 GB of RAM, the X55:
Intel Gemini Lake Pentium J5005 / Intel UHD Graphics 605 / 8GB DDR4 + 128GB SSD - $245.99 - link


In my opinion, the model featured in this review offers the best balance of price and specs: a Celeron J4105, 6 GB of RAM, and a 128 GB SSD. The entry-level X45 has just 4 GB of RAM and a smaller SSD, yet it isn’t much cheaper. The X55, on the other hand, has a more powerful processor but costs considerably more. That said, if there are any promotions or sales, the X55 could turn out to be the better deal.

Computer specifications:
Operating system: Windows 10
Processor: Intel Celeron J4105 1.5 GHz (2.5 GHz in turbo mode)
Graphics: Intel® Intel® UHD Graphics 600
Memory: 6GB DDR4 RAM + 128GB SSD + SATA
Slot for an SD card up to 128 GB.
LAN — Gigabit LAN
WiFi — 2.4/5 GHz
Bluetooth 4.0
Display: 2x HDMI
External interfaces: 4x USB 3.0
Audio output — 3.5 mm jack
Dimensions: 115 x 102 x 43
Weight: 308 g

In essence, it’s not all that different from the Alfawise T1:
6 GB of RAM instead of 4
128 GB SSD instead of 64 GB eMMC
Intel Celeron J4105 instead of N4100.

Still, taken as a whole, this Beelink looks more appealing thanks to these little improvements. But let’s take things in order and get on with the review.

This time, the manufacturer decided to move away from the familiar cube-shaped boxes that look a lot like Intel processor packaging, and went with a fairly large rectangular box instead.
Everything inside is packed quite tightly, so no complaints about the packaging from this company.


The package contents are pretty standard for Beelink products and include:
1. Computer.
2. Power supply
3. Short HDMI cable
4. Long HDMI cable
5. VESA mount
6. Power supply
7. Assorted mounting hardware.
8. Manual and other printed documentation.

A little more detail about what’s included:
1, 2. Along with the manual, there’s a quick guide explaining how to activate Windows. The main manual also includes Russian, which I’d like to thank the manufacturer for. It’s a small thing, but a nice touch.
3. Two HDMI cables, about 20 and 80 cm long. Each cable comes with a hook-and-loop strap bearing the company logo.
4. The VESA mount is simple but quite convenient. They also included plenty of different screws,
for attaching the computer to a display, securing the computer, and installing a hard drive. There’s one more screw of each type than needed.
5, 6. A 12 V, 2 A power supply. It’s enough for the computer, even with a hard drive installed later on. But if you also plan to charge a smartphone from the computer’s USB ports or power something demanding, the power supply may not be up to the task.


The appearance is also a little different from previous models, although the signature red button is still there. It even lights up nicely when the computer is running, in the shape of the standard power symbol.


The main difference in its appearance is that the computer is about one and a half to two times taller than previous models.


The top of the case is plastic; everything else is metal. The plastic shows fingerprints easily, and there’s no protective film.


1. The front has two USB 3.0 ports, a 3.5 mm jack for analog audio output, and the power button.
2. The rear has the other two USB 3.0 ports, Ethernet, two HDMI video outputs, and the power supply input.
3. The left side has only ventilation holes.
4. Besides ventilation, the right side also hides a microSD card slot—you might not notice it at first.


The bottom is metal too. And finally, Beelink’s engineers figured out how to make proper feet that don’t need to be peeled off to open the case or install a hard drive.


There is still one annoying flaw: after unscrewing the bottom, you have to pry it off (push it out) with something thin through the ventilation holes :) Naturally, it's best to turn off the power first.
There is room inside for a hard drive, and the metal case effectively acts as a small heatsink. The SATA connector is stuck to the side with cloth tape, so you'll need to peel it off before connecting it.


It looks like they unlocked just about everything in the BIOS. There are a lot of settings, but let me remind you once again that changing some of them can brick your device. Be careful: you can't reset the settings by disconnecting the battery, since it only powers the clock.


I'm glad they didn't remove the option to automatically turn on the computer when power is applied, as some other manufacturers sometimes do.
I won't list all the settings; there are too many. If there's anything specific you're interested in, let me know and I'll take a look.


When you turn it on, the familiar Beelink logo appears, along with a message saying you can enter the BIOS by pressing Escape or Delete. In my case, though, only Delete worked.


The desktop is almost empty; the system is installed with the default settings.


Windows 10 Home is preinstalled, and the system was already activated.


While preparing this review, I noticed that the screenshot doesn't show the available space. It's about 102 GB out of 118.


Windows is installed in English. Since people often ask me how to "Russify" it, I put together a short guide. Not everyone needs it, though, so I'll tuck it under a spoiler.


Basic information from CPU-Z. Some fields have been left at their default values by the manufacturer, such as the motherboard name and manufacturer.
Here are the first benchmark results. Compared with the Celeron J4100, the difference is barely noticeable—at most 5%, and only in one test.


The computer has a 128 GB SSD from an unknown manufacturer; at least, it’s simply identified as SSD 128G. It had no hours on it initially; this screenshot was taken after some testing.


Performance is pretty good, which was also apparent from the system’s boot time. The third screenshot shows a different SSD connected to the SATA port intended for a 2.5-inch hard drive.


USB 3.0 performance was also fine, although of course it’s still slower than a direct connection to the SATA port. The microSD card, on the other hand, is rather slow. Atom processors used to have a built-in card reader controller, and performance was very high: with fast cards, I got up to 90 MB/s. Here, with the same card, it’s only around 23–25 MB/s.


The graph in HD Tune looks a little odd, though.


The results are about the same in the 45 GB file test, although write speed never dropped below 200–250 MB/s.


From here on, I’ll periodically compare this computer’s results with those of its younger “sibling,” based on the Celeron J4100 processor, which I’ve already covered.
First, Cinebench.
In both tests, the computer under review is about 15–20% faster, which makes sense: it runs at 1.5 GHz, compared with 1.1 GHz for the Celeron J4100.


The same performance gain holds in PassMark, although here the SSD also helps, since it’s faster than the eMMC in the Alfawise T1.



In PassMark 8, the difference was about 10%.


But then things got strange. I suspect the thermal protection thresholds aren’t configured quite right—or, more specifically, the hysteresis. Apparently, the cooling system doesn’t have enough thermal capacity to compensate for the rapid temperature rise, so the processor throttles. The fan then spins up and the temperature drops, but not enough to switch out of this mode.
As a result, instead of the Alfawise T1’s 3117 points, we get just 2422 in 3DMark 2006.

What’s more, the results varied by as much as a factor of 1.5—not within the test’s margin of error (say, +/- 20–30 points).


The picture is even worse in the newer version of 3DMark. There, the score was consistently over 300 points; here, it’s just 116. The test results also varied considerably from run to run.


Geekbench was more or less fine: the computer under review was about 5–6% faster in the math tests and 15–17% faster in graphics.


The same problems showed up in LinX. The first run scored around 20 Gflops, compared with 17 for the Alfawise T1, but subsequent runs managed only about 14–15, versus 16. The temperature initially spiked above 90 degrees, then fluctuated between 65 and 70 degrees.


The OCCT tests ran without problems, and even the average temperature wasn’t high, but there were still occasional sharp spikes to around 90–92 degrees.



Like the vast majority of modern mini PCs, this model has a gigabit network card based on a Realtek chip and an Intel Wi-Fi module. I don’t know why, but this combination has become something of an unofficial standard and is genuinely very common.


As is often the case—and as I mention in almost every review—Intel’s Wi-Fi modules usually aren’t particularly sensitive. For example, a recent mini PC with a module from another manufacturer “saw” 66 access points in the same spot; this one found only 28.


The speed test results are also fairly predictable: around 10–40 Mbps in the 2.4 GHz band within a large room—10–15 in the corner opposite the router, and up to 40 a meter away.
The 5 GHz band is clearly better, at around 100–115 Mbps; with a gigabit connection, it was about 800–850 Mbps.


Now we can take a look at how it’s all put together and, along the way, try to figure out how the cooling system works.
Let’s disconnect the SATA connector so it won’t get in the way while we take this whole thing apart.


The assembly is reasonably neat and relatively compact.


As I mentioned above, the SSD is from an unknown manufacturer and is based on an SM2246XT controller and two Toshiba flash memory chips.


This was a bit of a surprise: it turns out there’s an mPCIe slot hidden under the mSATA connector. I hadn’t seen it mentioned in the specs, and only later spotted it in one of the photos on the store page.


The WiFi module cables are glued in place with hot glue. To remove the board from the case, you’ll have to carefully peel them off the board.


As I expected, the antennas are glued to the top cover of the case and positioned as far apart as possible.


A closer look at the board.


The heatsink and fan are on the underside.


Hot air is blown toward the back of the case and then exits through the ventilation slots. In my opinion, this isn’t ideal when mounting it to a monitor with the connectors facing down. I’d probably mount the computer on its side or with the connectors facing up instead.


The fan runs on 5 V and draws 200 mA. It has a four-wire connection. I’ll digress a little here to talk about how it works and how it affects the test results.
The thing is, its speed is automatically controlled, which is good. It’s also very quiet—I didn’t even notice when it was running at low speed, which is another plus. But it’s configured to kick in only once the temperature is already quite high. As a result, there are times when the processor throttles due to overheating, reducing overall performance.
So tests with a continuous load produce better results than those where the load keeps changing. For example, LinX may seem like a constant-load test, but in reality the processor load fluctuates between 50 and 100%, dropping toward the end of each pass.


To remove the fan, first peel off the plastic shroud, then undo the two screws.


And here’s the heatsink itself. You can see that only a relatively thin section sits above the processor.


All right, let’s undo three more screws and remove the heatsink. We should see how this design works.


A thermal pad about 0.7–1.0 mm thick is used as the thermal interface. It’s not bad, but I’d still replace it with a metal shim and thermal paste, especially since there isn’t much heat to deal with here. The design itself is reasonably sound.


As it turns out, there are plenty of components on this side of the board too.


I usually pay close attention to the presence of various port protection circuits, since they say something about the manufacturer’s attitude toward its product and how much they’ve cut corners. I can say that this board does an excellent job.
1. Protection for the rear USB ports.
2, 3. Protection for the front USB ports.
4, 5. Both HDMI ports are protected, and there’s another chip next to one of them.
6. What’s more, even the card reader lines are protected. I’ve never come across that before—nice work.


A few more details about the installed components.
1. Processor
2. Two RAM chips, for some reason with dual markings.
3. Processor power controller
4. SuperIO chip
5. Flash memory for storing the BIOS firmware
6. I’m not quite sure about this one: another flash memory chip. You might assume it’s for the network interface chips, but they’re a long way away. So for now, it’s a mystery.


1. A gigabit network chip from Realtek—the classic choice.
2. WiFi module from Intel
3. ALC269, an audio chip also from Realtek
4. The card reader chip is marked Realtek too.
5. I didn't understand this part at all. The thing is, MB3243I is a COM port transceiver. What's more, this is even marked next to the chip, but it's not mentioned anywhere in the specifications...
I understand that sometimes a universal board is designed and populated with components depending on the device's version and price, but soldering in a chip that isn't used here is strange.
6. It's also rather strange—or, more precisely, unusual—that they put a fuse on the power input.

Judging by the overall design and the presence of protection features, I'd guess this is some kind of “export” version of the device, since this is extremely rare in Chinese mini PCs.


And, of course, power consumption.
1. Powered off
2. Desktop
3. Maximum load in OCCT
4. Maximum recorded power consumption.


Various video files play without a hitch, and CPU usage is about the same when playing 4K video (file: 4k hdr demo 60fps wildlife video for 4k oled tv audio).


And also another file in 4K resolution (filename: Peru 8K HDR 60FPS 3840x2160).


But what surprised me more was that the computer also played the Peru 8K HDR 60FPS file at 7680x4320 without any particular problems.


Here's a summary table of the results. For the Geekbench test, I used the second run's result, not the first, when the processor was definitely running in “turbo” mode.
I also left in the low 3DMark test result; I may look into that again later.



And, of course, my conclusions.
Overall, I liked the computer, but as they say, “there's one catch.”
Considering that it has a fairly fast processor, 6 GB of RAM, a 128 GB SSD, room for a hard drive, an mPCI card slot, two HDMI outputs, and four USB 3.0 ports, I'd say it's very good for the price—at least better than the popular “Atoms.”
It also has relatively good build quality and protection on almost all the ports that “stick out,” even the microSD slot.

But unfortunately, there is a fly in the ointment. The test results surprised me a little—or, more precisely, their inconsistency. In the review, I suggested this might be due to the cooling system's behavior, perhaps because of a less-than-great thermal interface, or perhaps because the manufacturer wanted to make the computer quieter. As a result, when the load suddenly increases, the temperature rises just as sharply; then the fan kicks in, and the temperature fluctuates around 65–70, peaking at 75, which is perfectly normal. But the spike reaches around 90–92 degrees and affects performance.

Otherwise, I have no complaints. Well, I could perhaps nitpick about the second oddity: an mSATA SSD instead of the newer M.2, which is also unusual. Of course, stores are full of drives in both form factors, but it's still strange.

I'll answer the question about the X55 version right away. I think it'll be much the same, adjusted for its higher performance to begin with.

That's all from me. I hope you found the review useful.
$198.99
Go to store
This page was found when searching for:
12, beelink x55 тест температуры, bf05008h05fp fan, beelink x45 bios новая версия 0.16, bf05008h05fp, beelink j45 видеокарта, beeline gamini x 6g характеристики, beelink gemini x45 тест, beelink gemini x схема, мини пк beelink gemini t34, мини пк beelink gemini lake refresh j4125, beelink gemini x не включается, beelink gemini x45 чипсет, beelink gemini m 4pda, beelink gemini x45 мини пк, 4pda beelink gemini m, beelink gemini x55 обзор, beelink gemini x55 ddr4, beelink gemini x55 отзывы, beelink j45 обновление, beelink gemini n50, beelink gemini обзор, обзор beelink ap45 j4205 windows10 mini pc 8gb 128gb dual band wifi 1000mbps, флеш память beelink gemini x, мини пк beelink j45, мини ПК Beelink Gemini X45, обзор миникомпьютера Beelink, Beelink отзывы, мини компьютер Beelink Gemini X45

Questions and answers

What ports does the Beelink Gemini X45 Premium have?

It has four USB 3.0 ports, two HDMI outputs, Gigabit Ethernet, a 3.5 mm audio output and a microSD slot. There is also space inside for a SATA drive.

Why were the Beelink Gemini X45 Premium's test results inconsistent?

The author suggests that the cooling system or thermal interface may be responsible. When load rises sharply, the temperature first reaches 90–92 °C, then falls and fluctuates around 65–70 °C after the fan starts.

What storage does the Beelink Gemini X45 Premium use?

The reviewed configuration has a 128 GB mSATA SSD, with about 102 GB of 118 GB available in the system. The case also has room for a SATA hard drive.


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments6

Comments are published in their original language.

  1. Сергей
    18 September 2018 14:56#1
    Андрей, а mPCIe рабочий?
    Вы не пробовали в него вставить SSD?
    0
    1. 18 September 2018 15:10#2
      SSD в нем работать не должен, по поводу остального попробую на днях проверить.
      0
  2. lotana50
    26 December 2018 21:59#3
    У меня стоит ссд 120 гб. под систему а родной 64гб. под мусор. Работает.
    0
  3. Dmitry
    6 February 2019 20:29#4
    Сегодня получил X45 Premium, все работает, BIOS уже обновленный с завода.
    Только вот не могу в BIOS найти как отключить подсветку кнопки питания, уж очень ярко она светится
    +1
    1. 9 February 2019 19:52#5
      Так вроде в BIOS нет такой опции.
      -1
  4. 6 May 2020 16:42#6
    mPCIe рабочий? Можно вставит ssd? Или только планку переходник с 2мя Micro-SD?
    Спасибо
    0

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister