ZC823 v13, updated version of the multi-port charger board
$8.13 (без учета доставки)
One of my regular readers sent me this board for review—many thanks to him. He was also interested in the updated version. The price difference between the two was very small, and it seems the previous version has now been discontinued.
The packaging is the same as last time: an antistatic bag with a snap closure.

Since the board is designed to be installed on a cross board (which I’ve already covered), its dimensions are exactly the same as the previous versions: 45x21 mm, excluding the contact tabs.

As with the previous versions, the overall build quality is pretty good. I have a few minor complaints about the component soldering, but overall it’s quite decent.

As with the previous version, the board has two types of connectors: a standard USB-A and the newer USB-C. Only one can be used at a time, both mechanically and electrically.

The only visible difference is the color of the circuit board: the V11 was green.

The underside is just as clean and tidy. The input has a fuse and a 24 V TVS diode, which also provides reverse-polarity protection. The fuse is the same type as on the board with universal input, so the input current can be high. The previous board had a lower-current fuse.

1. The converter’s power transistors are the same, marked 5C670L. There’s a spot for a capacitor to the right; it was populated on the previous version, but it’s empty here.
2. The controller, however, is different. The V11 had an SW3516, while this one has an SW3518S. The transistors that connect the board’s outputs and the shunts are also unchanged.
3. The inductor and capacitors are unchanged as well.
4. The USB-A connector has five contacts.

Unfortunately, I couldn’t find a datasheet for the chip used here. What’s more, it’s not even listed on the manufacturer’s website—only the version without the S is available.
I did find a fragment of the datasheet, though, in truncated form. It specifies a maximum output current of 5 A—not at the chip itself, of course, since external transistors are used, but in terms of the supported control protocols.

There’s a more complete datasheet for the SW3518. In my opinion, it’s the same chip.

A side-by-side photo of the old and new versions.

All tests were performed with an input voltage of 24 V. The board is very efficient: with no load, my power supply shows a current draw of less than 1 mA. That’s a very rough measurement, of course, but in practice it’s unlikely to be much higher than that.
When I connect a USB tester to the output, the converter starts up and the current draw immediately rises to 9 mA, some of which goes to power the tester itself.

Almost the entire list of supported protocols is green; only Samsung AFC is marked in red. I also had to power the tester externally for this test. I’ll explain why below.

1, 2, 3. QC2 and QC3 are fully supported. The chip is listed as supporting QC4 and QC4+, but I don’t yet know how to test those.
4. Huawei FCP is supported.
5, 6. Huawei SCP is supported. This is exactly why I had to use external power: the minimum voltage can be set to 2.98 V, which makes the tester shut down.
7. Samsung AFC is supported; the earlier result was most likely an auto-detection glitch.
8. PD 3.0 mode is supported, which is good, but for some reason it only goes up to 20 V at 3 A, i.e. 60 W...
9. In “fine” adjustment mode, the available range is 3.3–21 V at 3 A, but the highest voltage I could set was 8.2 V. Even that took some fiddling: first I had to use the 1 V step adjustment to set 8 V, then switch to 0.1 V steps.

I checked it with a second tester just to be safe. I also used it to test connections through both USB-A and USB-C.
1. Since the tester doesn’t have a Type-C plug, I connected it with a cable.
2. Auto-detection through Type-C.
3. And through the standard connector.
4. QC also lets you set 20 V.
5. PD also tops out at 20 (21) V at 3 A.
6. For some reason, the tester didn't show support for VOOC DASH.

But what the tester reports is one thing, and what the board can actually deliver is another. Let's try it with an electronic load. The load was connected only to the Type-C output, and the protocols were selected using the tester.

First, 5 V in QC mode, although it actually makes no difference whether it's just 5 V or QC is enabled.
The maximum was 3.1 A. The output voltage rises as the load current increases. Even so, it stays within the 5.25 V tolerance limit, which is good.

I’ve hidden the QC, FCP, SCP, and AFC tests under a spoiler.
But I was more interested in the Power Delivery modes.
First, 5 V output—and again, the same 3.1 A :(

I’ve hidden 12 and 20 V under a spoiler, but there’s really nothing to see: the same 3.1 A, and I couldn’t get any more out of it.
With a 3 A load at 5 and 20 V output, the board got slightly hotter than the previous one. The difference was only a few degrees and could be explained by the different ambient temperatures during the tests.

Converter efficiency. In reality, it will be a little higher, since the USB tester itself added some load that I haven't accounted for.

And this is what the efficiency measurement setup looked like.

Ripple with no load is about 40–45 mV at 5 V output and about 30 mV at 20 V.

Under load:
1, 2. 5 V at 1.5 and 3 A: 40 and 45 mV
3, 4. 12 V at 1.5 and 3 A: about 65 mV
5, 6. 20 V at 1.5 and 2.5 A: about 45 and 25 mV
The results are identical to those for the previous board.

After seeing the test results, I even started to wonder: could I have accidentally bought the wrong board?
No, though—everything checks out. The old board is on the left; it’s the V10 version in the photo (if you look very closely), and the new V13 version is on the right. Just as shown in the review and listed on the page: 100 W.
You might assume that figure is for both ports at once, but that doesn't add up either: the chip won't power both ports simultaneously, and you can't physically plug in two connectors anyway.

Well, these are all boards from YZXstudio, namely:
1. ZC822
2. ZC823 v11
3. ZC823 v13 (also known as ZC823P)
4. ZC826

Now that I have the complete set of boards, the cross-board will probably be the subject of one of my next reviews :)

Based on the test results, I have to say I'm disappointed: I still couldn't get 100 W. But the bigger problem is that I can't figure out “who's to blame and what to do.” Either the board really can't deliver 100 W, or my tester can't set it to that operating mode. But when checking PD, the board itself reports its capabilities to the tester.
So for now, it's hard to say anything definite, but I've tested everything I could. As a bonus, here's a link to an extensive test of various chargers. It's in Chinese, but if you're interested, you can translate it using Chrome's built-in translator.
$8.13 (без учета доставки)
This page was found when searching for:
схема платы sw3518, sw3518 схема, sw3518s доработка, ljhj,jnrf gbnfybz ntcnthf n4, sw3518 с монтажом, sw3518s схема, sw3518 обзор, zc823p модуль, модуль зарядного устройства sw3518 обзор, zc826, sw3518, sw3518s, sw3518s datasheet, zc823p, zc822, ipod версия платы magic v2, http
схема платы sw3518, sw3518 схема, sw3518s доработка, ljhj,jnrf gbnfybz ntcnthf n4, sw3518 с монтажом, sw3518s схема, sw3518 обзор, zc823p модуль, модуль зарядного устройства sw3518 обзор, zc826, sw3518, sw3518s, sw3518s datasheet, zc823p, zc822, ipod версия платы magic v2, http
Questions and answers
What maximum output did the ZC823 v13 board deliver?
It delivered up to 3.1 A in most tested modes and 5 A in Huawei SCP. The author could not confirm the advertised 100 W.
Which charging protocols does the ZC823 v13 support?
Tests confirmed QC2, QC3, Huawei FCP, Huawei SCP, Samsung AFC, and PD 3.0. The author obtained a maximum of 20 V at 3 A in PD mode.
How does the ZC823 v13 differ from the previous version?
It uses an SW3518S controller instead of the SW3516, and its input fuse is rated for a higher current. The board dimensions and main power components remain the same.
The figures from this review are in the measurement database: Chargers
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments4
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister









Comments are published in their original language.