Another NTP-synchronized clock with an LED display
$4.84
A reminder: to keep up with new posts on the blog, I recommend following me on Instagram. I’ll post notifications about every new article there, and might also write about something interesting from time to time — link to my account
I bought this clock for two reasons. First, the price: it’s almost half the cost of the previous one. Second, I thought it might work better for what I have in mind.
I placed the order, waited a while, and eventually picked up a small envelope with a little box inside from the post office.

As with the previous model, there are a few display color options, but there’s no version with a black background.

Unlike the previous one, this model even comes with a piece of double-sided tape.

The display is the same size as the one on the previous model—in fact, it’s the same display, just with a white background.

The clock’s dimensions are listed on the store page.

During my initial inspection, I noticed the name SiniLink, but didn’t think much of it at first. I just had a vague feeling I’d seen it before.

Unlike the previous model, this one has an L-shaped design made up of two circuit boards, and there are no fewer than three ways to connect the power supply:
microUSB
USB-C
Contact pads on the board.

All the main components are mounted on one board, though, so you can simply desolder the extra board if needed.

1. The clock is controlled by an ESP8285.
2. The TM1650 handles the display.
3. It also has an RTC DS1307 and a battery to keep the clock running when external power is disconnected.
4. There are three buttons: set/up/down. In practice, though, each button has several functions, accessed by holding it down.

The product page describes the functions and settings, but most of them are intuitive. You can also configure the clock using an app on your smartphone, and in any case, you only really need to do that once.

The display is quite bright, which makes it hard to photograph, so I had to use the light filter from another clock again.

A few notes on the settings.
1, 2. Hold the SET button for about 1–2 seconds to set the time, date, and even the year, so you can use the clock without synchronization.
3. Hold the SET button for about 5–6 seconds to turn the alarms (6 of them) on or off and set their activation time.
4. Briefly press the "down" or "up" button to adjust the brightness.
Also:
5. Hold "down" to switch the display mode: time only, date only, or automatic date/time switching.
6. Long-press "up" to enable sleep mode; the display turns off after a few seconds and stays off until you press any button.

Some reviews complained that the display is too bright even at the lowest setting. That’s true if you use it without the filter, but with the filter, the brightness adjustment works just right.
I really miss automatic brightness adjustment using a sensor, or at least a day/night setting.

The clock’s power consumption is relatively high: 75 mA at minimum brightness and 95 mA at maximum. It looks like WiFi accounts for most of it.

If you hold down the SET button for a very long time (about 10 seconds), the clock enters connection setup mode. AP mode is clear enough—it’s access point mode—but I never figured out what GON means. Surely not “Garage of Special Purpose” :)

And now we’re gradually getting to automatic synchronization and connecting to a smartphone. You’ll have to do this at least once.
Here we’re back to the same mess I described in my review of the adjustable voltage converter.
You’ll need to install the SiniLink app (available in the Play Store), then, with a lot of swearing, connect the clock to it.
Sure, by the third or fourth try you’ll get the hang of it and it’ll be easy. But the thing is, you don’t connect devices very often, and I’ve already forgotten how to do it—even though it hasn’t been that long since I reviewed the converter.
Even 8 screenshots don’t give you the full picture of all the steps. After installing the app, you’ll have to do more than just launch it: you’ll also need to register for their cloud service, which I find rather inconvenient.
So, you’ve installed the app, registered, and signed in. It’ll offer to update; you can update or skip it, it makes no difference.
Put the clock into AP mode; the blue LED should start flashing.
Next, tap the plus sign in the main window to add a device, then select AP mode in the next window.

1. Enter your access point name and password below. The access point must be 2.4 GHz.
2. Set a device name and a group name. You can enter anything; it’s just to make the device easier to find later.
3. This step often causes problems because the app doesn’t always let you enter anything.
4. Start the connection process. A prompt will appear telling you to connect to a device named SinilinkProduct.
5. Open the WiFi settings on your smartphone, find the corresponding AP, and connect. No password is needed.
6. You’ll return to the previous window. Scroll down and tap the connect button. The app will complain that it can’t connect; accept the prompt, then tap again—once, twice, or three times...
7. Eventually, you’ll get a notification that the device has been found and that you now need to reconnect to your WiFi network with internet access.
8. Open your smartphone’s settings and switch back to your WiFi network.

After all that, the little red LED should light up, meaning the clock has connected to your router. The LEDs aren’t very bright and just stay on while it’s running, so they’re not annoying.

1. The clock now appears in the app. Great! Tap it to open the settings menu.
2. There aren’t that many settings, and once again there’s no option to switch between winter and summer time. At least you can adjust the brightness.
3. Since all communication goes through the cloud, the app takes a moment to “think” after each settings change.

There’s a description on the store page, though everything is clear enough as it is.

By the way, setting the alarm this way is easier.

I tapped the sync button. The app took a moment to think, and then the clock changed from “Chinese” time to ours—but it turned out to have changed in a strange way.
The clock had jumped ahead by about 2.5 minutes, which I couldn’t make sense of.

I thought it only synchronized the hours and seconds, but that seemed ridiculous, so I had to experiment. I tried it a few different ways, but on the next sync attempt everything was fine. Then I set the time to some random value and synced again, and it worked correctly.
But imagine my surprise the next day when I found that my other clock, which also has synchronization, was running about 2.5 minutes fast too. I couldn't understand this at all, especially since they sync once a day at 2 a.m., and there had already been another sync between these events.
Forcing a sync corrected the time, but I'd be very grateful if someone could explain how two synchronized clocks can drift by 2.5 minutes after syncing.
I'm sure they were keeping accurate time just a couple of days earlier.

Well, that's about it. Time to sum things up.
Overall, these are decent clocks, with several power options, manual time setting, and alarms. But unfortunately, they also have a whole bunch of drawbacks:
1. No automatic brightness adjustment.
2. No daylight saving time adjustment
3. The clocks stay connected to the router all the time, not just when syncing
4. High power consumption.
5. The software. I can't even talk about it without swearing.
Seriously, what's the point of cloud-based software for a clock? It works today, but tomorrow they could shut down their server, and then how the clocks will sync is anyone's guess... And the need to register, along with all the hassle of the initial setup, has earned them a special place in hell.
So, that's that. Would I recommend them? Well, probably the first clock is better, even if it's more expensive and has no alarms.
$4.84
This page was found when searching for:
часы настенные с синхронизацией времени по wifi, часы с синхронизацией времени ntp, часы светящиеся с синхронизацией, для чего нужна синхронизация светодиодных цифровых часов, ntp led clock, электронные часы с десплеем и возможностью синхронизации, обзор sinilink включение пк, часы с настройкой включения и яркости, часы sinilink, синилинк не подключается к wifi, часы с синхронизацией, часы с wi-fi, ntp настройка, sinilink wifi clock
часы настенные с синхронизацией времени по wifi, часы с синхронизацией времени ntp, часы светящиеся с синхронизацией, для чего нужна синхронизация светодиодных цифровых часов, ntp led clock, электронные часы с десплеем и возможностью синхронизации, обзор sinilink включение пк, часы с настройкой включения и яркости, часы sinilink, синилинк не подключается к wifi, часы с синхронизацией, часы с wi-fi, ntp настройка, sinilink wifi clock
Questions and answers
How much power does the SiniLink clock use?
The author measured 75 mA at minimum brightness and 95 mA at maximum. Wi-Fi appears to account for most of the draw.
What can you configure on the SiniLink clock?
You can set the time and date manually, configure six alarms, choose the display mode, and adjust brightness. Settings are also available through the SiniLink app.
What drawbacks did the author find with the SiniLink clock?
It has no automatic brightness adjustment or daylight-saving change, stays connected to the router, and draws relatively high current. Initial setup requires cloud-app registration and proved difficult.
Calculate manuallyAll calculators
Discounted products
You may be interested in
Discounted products
Support the project
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments8
Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forumOnly registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister




Comments are published in their original language.