/       /       /    EM-130 Programmable WiFi Astronomical Timer by Novatek-Electro
Support the project on Patreon


EM-130 Programmable WiFi Astronomical Timer by Novatek-Electro

1035₴ (около $37)
Go to store
Today I’m reviewing an outwardly ordinary timer, but one that can do more than just switch at set intervals: it can also schedule switching based on sunrise and sunset, which can be more convenient than a conventional photocell switch in some situations.


I should probably start by saying that I reviewed a similar type of relay a little over five years ago, and as far as I know, at least one of them still seems to be working.
The link in the title points to the Ukrainian version of the site. As I understand it, this is a new device and it isn’t sold in Russia yet.

And, of course, a quick explanation of what an astronomical timer is.
There are ordinary timers: you set the on and off times. I think most people are familiar with them.
An astronomical timer does almost the same thing, but it’s synchronized with the solar cycle. As you know, the sun rises and sets at different times depending on the day of the year and your location. So this type of timer “knows” when the sun sets and can switch something on at that time. These timers are used to switch outdoor lighting on and off (most commonly), or, for example, illuminated signs, as in my first case. You can also set the timer to switch on or off early or late, or configure more complex schedules. For example, turn the lights on half an hour after sunset, off at one in the morning, on again at five in the morning (if the sun hasn’t risen yet), and off half an hour before sunrise.

Of course, you can buy a photocell switch. That’s what people often do, and it’s much cheaper. But I wrote this then, and I’ll say it again now: a photocell switch is more convenient in some ways because it takes overcast conditions into account, but it also has drawbacks. It needs maintenance (a simple cleaning to remove dirt, dust, or snow), and it has to be installed outdoors. You also need to find a spot where streetlights won’t shine on it. Otherwise, everything might work fine today, but tomorrow the neighbors put up a light of their own and the “light show” begins. In other words, an astronomical timer behaves more predictably.
That said, none of this means an astronomical timer makes sense for everyone. Some people have a convenient place to install a photocell switch, where the sensor is protected from the weather and stray light, and so on. In that case, there’s no real reason to use an astronomical timer.
A photocell switch also follows a more rigid schedule. For example, simply turning the lights off overnight would require adding a timer.

I can also foresee comments along the lines of, “I could build that on an Arduino in half an hour, with three smoke breaks.” Sure, if you have the time and the skills. But not everyone can program, and some people have no interest in doing so. And if you add up not just the time spent writing the program, but also assembling the whole thing, buying one may turn out to be the better deal.


The Chinese-made product was certainly cheaper, but the question is whether the only difference is the price, or whether there are other differences too. One difference is already clear from the review title: it supports a WiFi connection. Novatek also offers a “classic” version with its own screen and keypad, the REV-225, which even looks a bit like the one I reviewed. Link for readers in Russia.




So, the packaging is in the familiar style: a small box with the manufacturer’s name and a sticker indicating that it contains an EM-130 timer.


The only thing included besides the timer is the manual.


The manual is detailed, with technical specifications and instructions for setup and connection. It also states that the product comes with a 10-year warranty, which is also mentioned on the manufacturer’s website.


The complete manual is available at this link. I’ll include just a few screenshots from it.
First, the technical specifications.


That’s enough of the introduction. Let’s move on to the subject of the review.


The housing is one unit wide and looks a little smaller than a standard circuit breaker.
It’s a little unusual to see two latches at the bottom instead of one, although the previous timer had the same arrangement. It just didn’t have metal springs.
There’s a sticker on the side with the serial number, basic technical specifications, and firmware version.


1. Two terminals on top for the power supply, along with the operating voltage range.
2. Two groups of relay contacts at the bottom; both are changeover contacts. In both cases, the terminals are the proper type, just like on other devices from this manufacturer.
3. There’s a wiring diagram on the side, along with the rated current of the circuit breaker and the maximum load power. Though I’d probably put the circuit breaker before the point where the power supply splits between the load and the timer.
4. The front panel is as minimalist as it gets, with only an operating-mode indicator LED and a control button.

The control button performs several functions, depending on how long it is held down.
1–3 s: Restart the device.
5–8 s: Switch the device to Wi-Fi setup mode.
10–15 s: Reset to factory settings.
> 15 s: No action is performed.

The LED also helps during setup by counting out one-second intervals.



Overall dimensions, terminal assignments, and indicator-mode descriptions.


Before testing, I took the timer apart to assess the build quality and circuitry. The two halves of the case are held together by clips and the top cover, but the construction itself is quite rigid.


There are two boards: the main board, with the controller and power supply, and an auxiliary board carrying the relay.
The lower row of output terminals is soldered to the auxiliary board, while the upper row is connected by wires. Everything looks neat; nothing is loose or wobbly.


Top view of the main board. The controller, Wi-Fi antenna, printed inductor, polymer capacitor, and supercapacitor are clearly visible.


The board is populated on both sides; in addition to passive components, there is an EEPROM on the underside.


There are components on the underside of the auxiliary board too: the input bridge rectifier, a choke in the high-voltage power circuit, the relay driver transistor, and various small parts. Near the input terminal there is a narrow trace that serves as a fuse. Protective slots in the circuit board are also visible.


There is also an X-class interference-suppression capacitor, as well as a resistor to limit the inrush current through the input bridge rectifier.


1. There are two input filter capacitors connected in parallel. Both are rated at 4.7 µF and 400 V, so it's best not to exceed the specified 275 V.
2. For additional protection, a 430 V varistor made by Littelfuse is installed on the board.
3. The power supply is non-isolated and built around an LNK306PN PWM controller. Another chip, marked 5430, can be seen further in; it's a TPS5430 DC-DC converter from Texas Instruments.
4. The relay is made by Hongfa and has a maximum rated contact current of 8 A. Novatek specifies only 7 A in its documentation, most likely as a safety margin.


1. Everything is controlled by the fairly well-known ESP8266. In my view, it has just one drawback: Wi-Fi operates at 2.4 GHz. That said, it's not a major issue here, as will become clear in the software section of the review.
2. Nearby is a PCF8523T RTC chip with a separate crystal resonator, which keeps the built-in clock. It is powered by a supercapacitor rather than a battery, which extends its expected service life. It provides 10 days of backup after being powered for at least two hours.


The hardware tests essentially came down to measuring power consumption. In standby, readings fluctuated around 0–0.4 W; with the relay on, they were 1.3–1.4 W.
As a minor downside, I'll mention a faint squeal when the relay is on. You can hear it from up to a meter away in a quiet room, though I think it will disappear completely once the unit is installed in a panel.


Initial setup is very straightforward: press and hold the button for 5–8 seconds, and the device will enter Wi-Fi setup mode. Open the Wi-Fi network list on your smartphone, find the access point named EM130, and connect using the default password: 00000000.
Then open 192.168.4.1 in your browser. A password prompt will appear (the default is admin) to access the settings menu.
Enter it and tap “Log in.”


The home screen displays:
1. A button in the upper-right corner to open the settings menu
2. The status
3. An operating-mode button (on/off), active only in manual mode; in automatic mode, it simply shows the status
4. An image showing the approximate current position of the sun or moon
5. And, at the very bottom, a switch for selecting the operating mode (manual or automatic).

From the settings menu, you can return to the status screen, open the schedule, go to the device settings, or disconnect from the device.

Schedule settings. This is empty at first; I'll show it in more detail later.



Settings.
1. Safety: you can change the current password used to access the device.
2. WiFi connection: when you open the settings, the device automatically starts searching for WiFi networks. Here you can change your WiFi password or connect to your WiFi network. You can also choose how the IP address is assigned: via DHCP or manually.


WiFi can be disabled or run in one of three modes: direct access to the settings (activated by pressing the button), access point, or client.

Since this is a timer, a lot of attention is paid to the time settings. You can set the device's time manually, synchronize it with the device you used to connect, or use an NTP server, either manually or automatically. In standalone mode, the stated accuracy is ±1.5 seconds per day, but you can also make a manual correction. There is also an option to account for the switch to and from daylight saving time.


But the key setting for an astro timer is its location, since sunrise and sunset depend not only on the time and time zone, but also on where you are. What's more, they can vary significantly even within the same time zone.

Enthusiasts building their own timers can keep things simple and hard-code a table for their location. Commercial devices need an option that lets the user enter this information. You can find your coordinates on Google or in a navigation app.

And that's not the end of the setup: you also have to choose how to define the day/night boundary, since there are several options:
Visible sunrise/sunset
civil twilight
nautical twilight
astronomical twilight.

At the end of the settings list, you can reboot the device, restore factory settings, or erase the schedule memory.



To be honest, I got a little confused here myself. In part, the answers to these questions are on Wikipedia.

In simple terms, the distinction is between when the sun goes below the horizon and when it gets dark, and how dark it gets. These aren't the same thing: the sun may already be below the horizon while it's still quite light outside.
Twilight ---- Sun's angle below the horizon
civil - from 0°50′ to 6°
nautical - from 6° to 12°
astronomical - from 12° to 18°

So, instead of setting a delay or advance for switching the lights on or off once it gets dark, rather than just when the sun disappears below the horizon, you can choose a different type of twilight. This will probably also account for the time of year: for example, it gets dark more gradually in summer than in winter.




The manual lists all configurable parameters, their adjustment ranges, and their default values.

I should probably digress briefly here. For some reason, I expected the device to connect to the Overvis cloud service for convenient remote control and parameter adjustment. It turns out, though, that it can only be controlled from within the local network. I suppose you could check which port the device uses and set up remote access, but as far as I can tell, that's not part of the basic functionality.



Now I'll describe how to set it up. The manual gives a typical example: the lights turn on after sunset, turn off four hours later, turn on again four hours before sunrise, and turn off after sunrise. This scenario is just an example, but it shows how every step can be tied to sunrise or sunset.


I'll show a more familiar scenario, like the one used in street lighting systems.
Go to "schedule"; it's empty to begin with.


Tap "new event" to open the event editor, where you can set:
Action - turn on or turn off
Event - sunrise, sunset, or a specific time. For the first two, you can set a positive or negative offset from sunrise or sunset. The third option sets an absolute time, i.e. a simple timer.
Day of the week - each event is tied not only to a time but also to a day of the week. For example, you can set one schedule for weekdays and another for weekends.

At first I got a bit lost, but figured it out mostly by intuition rather than by following the manual, which I think is written in a somewhat clunky style.


For example, let's first set the lights to turn on 15 minutes after sunset. To do this, select "on" and the sunset icon, then enter the time. If you need a delay, enter it in four-digit format: not 15 minutes or 015 minutes, but 0015. If you need to set the time earlier, enter a minus sign first.

Here I set it to switch on 15 minutes after sunset. Click "Add". You can then continue programming, or close this window and see what you get. The result is a program with the switch-on time already marked.
Don't be alarmed that the same time is shown everywhere. It will be different the next day (it updates automatically). In my opinion, this is an oversight, since it can be confusing. I think the programmers should display the correct schedule right away, including the switch-off times for the following days, for example through the end of the week.


Next, I set:
1. Switch off at 1 a.m.
2. Switch on at 5 a.m.
3. Switch off 15 minutes before sunrise.

The previous values in the settings fields aren't cleared during the setup session, but only the data in the active windows takes effect. This is confusing too. In my opinion, it would be more logical for the fields to clear after clicking "Add".


This gives us the program shown here. By the way, the order in which you enter events doesn't matter: the program sorts them into chronological order, or more precisely, the order in which they will run.

The histogram shows the relay's on state in green, sunrise/sunset times as horizontal yellow and blue lines, and the current time in red. Very handy. But the misspelling "swich on" instead of "switch on" looks ugly.

But wait, why is the relay on over the weekend, and where did that come from?
The explanation is simple: the relay retains its last state. If nothing is scheduled for a given day, and it was on during the night from Friday to Saturday, it will stay on until it receives a switch-off command. In my scenario, that won't happen until 1 a.m. on Monday.



It's easy to fix: add a switch-off event to the program, say, at 1 a.m. on Saturday. After that, do whatever you like: leave it as is, or schedule some more switch-ons.

1. Here I set it to switch off at midnight on Saturday and Sunday, although selecting Saturday alone would have been enough.
2. The histogram now shows the operating schedule, with the relay off on Saturday and Sunday.
3. If you make a mistake, you can easily "delete events" in either of two ways:
a. Click the red circle to the right of an event and select only the ones you want.
b. Scroll up and click the checkbox above the red circles to select everything.
Then choose "Apply" or "Cancel".


With all these features, you can also use it simply as a timer, but one tied to a specific time of day. Just for fun, I set the relay to switch on and off over the weekend, first after an hour and then after two minutes.
The timer's minimum setting interval is 1 minute.


Programs can be saved to an .ESL file. Here's the program from my first example:


And here's the second one, with timer-based switch-on and switch-off events added.

Note that the "Add from file" option adds a program rather than replacing the one currently in use. For it to work correctly, you need to clear the old program first, then add the new one.


There won't be a demonstration or tests today, since the screenshots have effectively covered the demonstration. As for testing, the relay works and switches the load on and off. There's no point checking the time accuracy: not only is there synchronization, but they've also added a correction feature, so you can adjust it on site.

Actually, I did run one more test: checking that the switch to winter time works correctly. You might say, “How could they get that wrong?” Turns out they could, which is why I tested it. I reviewed a clock that a Chinese manufacturer had modified for sale in other countries, where they needed to add daylight saving time (China has one time zone and doesn't use daylight saving time). Switching to summer time usually isn't a problem: you just move the clock forward an hour. Winter time is trickier, since you move it back an hour. Yes, you guessed it: in autumn, the clock gets stuck in a loop, continually moving back an hour. You can fix it by manually starting synchronization, but as they say, "it leaves a bad taste".
Everything works fine here: the internal clock moved back an hour and continued running correctly.

As a small extra, I measured the case temperature after several hours of operation with the relay on. I'd say it's excellent.


Here's what the operating mode indicator and the virtual "sky" display look like in the program.


Conclusions.
What I liked:
1. The construction: everything is neat.
2. Circuit design. Unlike the Chinese equivalent, this unit uses a switching power supply and includes a protective varistor; a supercapacitor is used instead of a battery.
3. Components. The components are name-brand and generously rated, and a polymer capacitor is used in a critical spot.
4. Features. The relay can work as a simple timer, or you can tie its switching times to sunrise and sunset and create complex schedules. To make it easy to switch programs, there are functions for saving and loading them.
5. Service features. It’s good to see that time synchronization (two options) and clock correction are available.
6. Ease of use. I had a few comments at first, while I was figuring out the setup logic. After that, I can say that putting together a program is a breeze. And setting the location is definitely much easier than on the Chinese equivalent, where you have to dig through the menus.
7. Ten-year warranty.

What I didn’t like.
1. No option to integrate with Overvis or control it remotely.
2. No input fuse. I don’t really trust PCB traces to act as fuses, especially when they’re upstream of the varistor.
3. Some parts of the manual aren’t very clear. I understand that it’s intended for someone with technical experience, but even I, with experience setting up a Chinese relay, ran into a few difficulties. I hope the description in this review will be easier to follow.

And of course, readers will probably want to ask: do you really need WiFi here, and is it worth paying extra for?
If you plan to install the device “once and for the long haul” and don’t expect to change the settings, the cheaper version is probably the better buy, since WiFi is only needed for setup. But the WiFi version has another advantage: because it doesn’t need a display, it takes up half as much space in the electrical panel. So whether to “have it or not” also depends on your particular situation.
It might be worth doing a comparative review of the standard version to make it easier to choose.

What I’d like to recommend to the manufacturer.
1. Integration with Overvis. In my opinion, it’s time for Novatek to build its own device ecosystem, because the range of devices like these will only grow, and it will get harder and harder to do later. For example, this is already my third review of a device with network access, but the previous two, although they work with Overvis, are still separate products that require different accounts.
2. Tidy up the web interface a little—for example, clear the input fields after applying their values, and fix the typo in the word “влючение.”
3. WiFi only works on 2.4 GHz. That’s certainly enough for control, but this band is quite congested, and you may run into problems in some situations.

Readers may have their own suggestions for the design or features, but that’s all from me for today. I hope you found this useful.
1035₴ (около $37)
Go to store
This page was found when searching for:
em 130 сбрасывает программу, таймер с программированием по wifi, настройка таймера вай фай ем 130, программируемый wi fi астрономический таймер em 130, ем 130, wifi астротаймер em 130 купить, em 130

Questions and answers

What can the Novatek-Electro EM-130 astro timer do?

It can switch a load at times relative to sunrise and sunset, with additional scheduled events such as switching off at night. The device is configured over WiFi.

How does the EM-130 differ from a photo relay?

It calculates switching times from the solar cycle and location, making its operation more predictable and independent of stray light. Unlike a photo relay, it does not respond to cloudy conditions.

Is the WiFi version of the EM-130 worth choosing?

WiFi is only needed for configuration, so the author says the cheaper non-WiFi version may be preferable if settings will not need changing. The WiFi model takes half as much space in the electrical panel because it has no display.


Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister