/       /       /    12.6 V 3 A Charger, or Continuing the Discussion About Converting a Cordless Drill Battery
Support the project on Patreon


12.6 V 3 A Charger, or Continuing the Discussion About Converting a Cordless Drill Battery

$10.99
Go to store
At the end of last year, I published a couple of reviews about converting cordless drill batteries. Today I’ll tell you about an alternative way to charge a converted battery using a ready-made charger.
As usual, we’ll take a look, take it apart, examine the circuit, and run some tests.

Last time, I suggested using an old charger with a separate converter board. It’s not a bad option, really, but people started asking what to do if the old charger is smashed, broken, or eaten by the cat.
Then I happened to come across a charger in one of the stores that should work with 3S batteries, i.e. 12.6 V. Since this is one of the most common configurations for converting old cordless drills, I decided to order one for a review.

The packaging is very basic, as is the label indicating the charging voltage and current.


The package contents are simple: a cable and the charger itself.


The cable is pretty good, but the plug is a letdown. The options are to cut it off, replace it, or find an adapter.


The charger is built in a power-supply form factor. It’s fairly hefty, and the case is sturdy.


One end of the case has a two-pin AC inlet; the other has a cable with the familiar 5.5/2.1 mm plug. The cable is about 1 meter long.


Since this is a charger, not a power supply you use to charge your phone or tablet, it has a charge-complete indicator. It’s not very bright, though, and won’t be visible in bright sunlight—or even under a camera flash, for example.

There’s a label on the bottom with the specifications. Nothing new beyond what was printed on the packaging.


As I mentioned above, the case is quite sturdy, but it couldn’t withstand a hammer and a knife. There’s no other way to take this thing apart.


The board is held very firmly inside. It’s partly attached with double-sided tape and partly glued in place with silicone around the power components. The photo shows the inside of the case, with some kind of adhesive residue left behind as well.


It looks economical, but the build quality is quite good. The heatsinks are insulated and held in place by the power component itself, an extra tab, and silicone sealant.
The transformer and input inductor are also glued to the case. Overall, getting the board out was quite difficult.


There’s a fuse and an input filter on the input. Unfortunately, there’s no thermistor; it’s been replaced with a jumper.


1. The input capacitor is 68 µF, which is quite enough for a power output of around 40 W.
2. A CS7N60F high-voltage transistor in a fully insulated package.
3, 4. A feedback optocoupler is tucked away on one side of the transformer; on the other is a proper Class Y safety capacitor, so you won’t get a shock.
5. The output diode assembly is rated for 10 A and 100 V, with plenty of headroom for both current and voltage.
6. The output capacitors are 1000 µF, rated up to 25 V, so no issues there either. There’s also space for an EMI suppression inductor and a third capacitor.


There are even more components on the underside of the board.


"Hot" side of the power supply. I didn’t have any issues here either—well, almost none :)


"Cold" side. This is where the voltage and current regulation components are, along with the charge-complete indicator.


My only complaint about the "hot" side was the soldering—or rather, its quality. It looks as if the PWM controller was resoldered, since the other components are neatly soldered in place.
No complaints about the output side: everything is neat, and the components are additionally secured with glue. The op-amp is an LM358.


Since I haven’t reviewed a device like this before, I had to redraw the circuit.
The primary side of the power supply turned out to be almost identical to the one in a power supply I reviewed earlier: 12 V 1 A Power Supply. The power supply is very reliable and well made.
The only differences are the values and number of some components; the IC has the same pinout.


Since the schematic is large, I split it into two parts to make it easier to follow: primary and secondary.
The secondary side differs from the usual power supply schematics because it contains more sections.


I'll describe the sections separately.
1. Green — output voltage regulation section, responsible for CV mode.
2. Red — current regulation, CC mode.
3. Blue — indicator section.
At the top left are two rectifiers: the main one and an auxiliary one (D3, C5) that powers the op-amp and LED. The auxiliary supply is needed so these components don't draw current when a battery is connected but the charger isn't plugged into the wall.
Between the red and blue sections is the reference voltage source for the indicator and current regulation sections.


Although most of the design is quite well done, there's one caveat. A 2.2 kΩ resistor (R13A) is connected in parallel with the first capacitor, so the unit still draws power when switched off. One possible fix is to install a diode (marked in red) in place of the jumper, which is in turn fitted where the missing noise-suppression inductor would go. But there's a problem: the diode will get noticeably hot, so I'd recommend leaving things as they are.
Now, what should you change if you need a different voltage/current?
1. Green — the divider in the voltage-sensing circuit. Increasing the value of the upper resistor raises the output voltage; increasing the lower one lowers it.
2. Blue — increasing the shunt value reduces the current; decreasing it increases the current. The change is proportional to the change in resistance. This resistor also affects the indicator reading.
R19, R13: increasing the upper resistor value reduces the output current; changing the lower resistor has the opposite effect.
3. Orange — the divider that sets the indicator switching threshold. The same principle as in item 2, but for the indicator. Note that this section has hysteresis, so the red/green switching is abrupt rather than gradual. A small detail, but a nice one.


A separate photo for perfectionists: here I've listed the components that can be installed on the board.
1. Y capacitors. Since the unit is connected without grounding, they serve no purpose. Replacing the socket with a three-pin one would reduce noise on the mains.
2. Thermistor to reduce inrush current. For example, an NTC 5D-9.
3. Output inductor. Reduces output ripple; rated for more than 3 A, with an inductance of 1–10 µH.
4. Varistor to improve the power supply's protection against high input voltage. 10 mm diameter, 470 V.
5. X capacitor to reduce noise on the mains; there's room for 22–33 nF.
6. Two-winding inductor, usually on a small core, also to reduce noise on the mains.
7. Diode assembly. You can install one in parallel with the first one to slightly improve efficiency and reliability. It's best to use the same type as the one already fitted: 10 A, 100 V.
8. Output capacitor. It won't make much difference to ripple, but may improve reliability. 1000 µF, 25 V.


Let's move on to the tests.
First, I'll go through the main points.
1. Output voltage — about 30 mV too high, which I consider well within the acceptable range.
2. Current drawn from the battery with the power disconnected: about 7 mA. That's quite a lot; it will discharge the battery in about 2–3 weeks. It's better to use protected batteries, although protection is essential in any case.
3. Charging current: 2.9 A, slightly below the stated value, but I don't think that's a problem.
4. The indicator is set to switch at 270 mA. When the charging current drops below this value, the green LED turns on and the red one goes out.
5, 6. Since the device can't completely cut off current to the battery, you'll see the current drop almost to zero. For example, it took about 8 minutes for the current to fall from 66 mA to 28 mA.
Charging without fully cutting off the current is acceptable, though not ideal. If the battery is in good condition, there won't be any problems, but I'd recommend not leaving it connected for too long — a day or two, for example.


Next, I connected the charger to an electronic load. But since the electronic load doesn't have a CV mode, I had to connect it around the current regulation circuit.
I set the load current to 3 A and closed the case to let it heat up. I also monitored voltage drift; there were no problems here either. A 5 mV change after an hour of heating is excellent, thanks to the precision resistors used in most of the circuit.


Since this is a charger, not a power supply, and it spends most of its time running at maximum current, I set the current to 3 A right away. The test ran for 1 hour, enough to fully charge a 2400–2600 mAh battery. After that, the current will start to drop anyway, so there's no point in testing the temperature further.


1. An hour later, I checked the case temperature. At the hottest spot, the device read 59 degrees, although the case didn’t feel hot to the touch. This may be because the plastic is partially transparent in the infrared range.
2. I opened the case and measured the temperature. The highest reading was around the primary-side snubber and shunt, at about 80 degrees; the transistor was at 70–72 degrees.
3. I closed the case for a couple of minutes, turned it 180 degrees so the other components were visible, and measured again. This time, the output diode assembly had the highest temperature, at about 85 degrees.

Based on these tests, I can conclude that the thermal performance is fine, with about 20–30 degrees of headroom before reaching critical temperatures.


To sum up, here are the main points:
Advantages
Solid, neat construction
Components are generously rated
Good parameter stability
No overheating
Clear indication when charging is complete

Disadvantages
Charging does not shut off completely
7 mA of power consumption when idle.
The cable plug has flat pins.

My opinion: I think the device has just one significant drawback: it doesn’t completely cut off the charging current. Proper charging continues until the current drops below 1/10 of the set value, then charging shuts off and starts again if the voltage drops once more. Of course, you could design a little hysteresis circuit that doesn’t shut off charging but instead lowers the output voltage enough to stop the charging current. But in my opinion, as long as you don’t leave the battery connected for a long time, the way it works now is perfectly acceptable.
I was pleased with the fairly good build quality and the fact that the components are generously rated. It’s also worth noting that it doesn’t overheat, unlike quite a lot of power supplies. I got the impression that the device was built around a 12 V, 5 A power supply, with the voltage raised a little and the current reduced, which would explain the result.

All in all, if you’ve rebuilt your cordless drill battery and it has a voltage of 12.6 V (three cells in series), and the original charger can’t be repaired, this is a pretty good option.

When I ordered it, the charger cost about 13.7 dollars. The manager lowered the price to 11 dollars for the review, which I think is quite reasonable for this device, considering its features and build quality.

That’s all. I hope you found the review useful.

$10.99
Go to store
This page was found when searching for:
устройство штекерного разьема блока зарядки для на 12 вольт для шуруповерта, 2, 10, схема зарядного устройства 12 вольтового шуруповерта метабо, из чего состоит зарядка, переделка китаиского зарядного устройства шуруповерта, доработка зарядного устройства шуруповерта, 3, электрическая схема блока зарядки распрыскивателя, схема китайской зарядки шуруповёрта 12.6 вольт, гайковерт не включается из-за недостаточно напряжения на третьем контакте аккумулятора, каким образом можно повысить напряжение на третьем контакте?, схема включения 63d39, зарядное устройство 12.6 вольт своими руками, зарядное устройство из блока зарядки шуруповерта, схема китайского зарядника для шуруповерта на 12 вольт, 1968b4ed2acbeb5209432d417296ece3, зарядное для li-ion шуруповерта 12v схема, 5e3436e2e58a607b92b5a0ec19f6bd6b, lp3783 схема включения, схема заряда свинцового аккумулятора 6v 3.2 ah, схема зарядки 21 вольт для шуруповерта, схема зарядного устройства шурупо, блок пмтания от шуруповерта tlbj07c v3, 6v акомулятор практические схемы зарядки от зарядки смартфона, power x charger 3a схема ремонт

Questions and answers

Can the 12.6 V, 3 A charger be used with a 3S drill battery?

Yes. It is intended for batteries made from three cells connected in series, with a voltage of 12.6 V.

What drawbacks did the author find in the 12.6 V, 3 A charger?

It does not fully shut off the charging current, and its off-state consumption is 7 mA. The supplied cable has a plug with flat pins.

How does the charge-complete indicator work on the 12.6 V, 3 A charger?

It indicates completion when the current drops below 1/10 of the set value. Charging can resume if the battery voltage falls again.

The figures from this review are in the measurement database: Chargers

Calculate manuallyAll calculators

Discounted products


You may be interested in


Discounted products


Support the project

All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!

Comments11

Comments are published in their original language.

  1. 17 February 2018 05:17#1
    Когда начинал читать обзор, сразу в уме стали возникать вопросы о "доработке" схемотехники. А к концу обзора, уже готовые рекомендации! Отличный обзор!
    Да, ссылка не открывается, блокирует браузер. Может осталось название магазина? Или рабочая ссылка? Хотелось бы взять, именно такой, а не тот, что в другом обзоре на те-же парраметры.
    +2
    1. 19 February 2018 23:34#2
      ссылка есть - http://www.tmart.com/3S20-29-4V-Charger-for-3-Series-Li-ion-Battery-Pack-with-U
      S-Standard-Power-Cable-Black_p265258.html
      Но увы, написано что распроданы :(
      0
      1. 20 February 2018 05:55#3
        Пробовал искать на Али по такой маркировке, не нашёл. У всех продавцов, как я заметил, одна марка таких ЗУ: XMS-L3S30.
        0
        1. 25 February 2018 21:02#4
          К сожалению другой информацией не располагаю, мне тоже зарядное понравилось, но вот насчет Али или Ибей :(
          +3
        2. Мимокрокодил
          16 August 2018 01:37#5
          https://ru.aliexpress.com/item/12-6v-3a-lithium-battery-charger-3-series-lithiu
          m-battery-group-charger-warranty/32461436139.html?spm=a2g0v.search0604.3.273.10
          704c12vD0BIY&ws_ab_test=searchweb0_0,searchweb201602_2_10152_10151_10065_10
          344_10068_10342_10343_5012915_316_10340_10341_10696_5013115_10084_10083_10618_5
          723515_5013015_10307_10301_10059_100031_5013215_10103_10624_10623_10622_10621_1
          0620,searchweb201603_13,ppcSwitch_5&algo_expid=a3187090-3226-4457-a412-e932
          50cd7b6b-40&algo_pvid=a3187090-3226-4457-a412-e93250cd7b6b&transAbTest=
          ae803_1&priceBeautifyAB=0
          0
  2. Игорь
    12 December 2018 15:00#6
    Привет! А в данном зарядом устройстве есть защита от переполюсации? То есть, если поменять полярность?
    +2
    1. 14 December 2018 03:08#7
      Так у шуруповерта сложно вставить батарею неправильно.
      0
      1. Игорь
        28 December 2018 21:36#8
        Попался такой товарищ, цвет светодиода меняется, а зарядки нет! В чем проблема? Транзистор сдох?
        0
        1. 4 January 2019 01:37#9
          Для начала надо проверить что он вообще как-то работает. Если включить без аккумулятора, напряжение на выходе есть?
          0
  3. 20 August 2019 07:34#10
    В первую очередь, мой огромный респект Kirich ! С большим удовольствием читаю и смотрю ваше творчество здесь, на Муське, и на Ютубе.
    Хочу посоветоваться. Хотел написать здесь на форуме, но смотрю у вас там какие-то проблемы, похоже вируса… Поэтому решил написать здесь.
    Имеется вот такая зарядка для лития 14S батарей. Заявленные китайцами параметры 58,8V-5А. На реальной батарее не проверял (пока нет такой батареи), но на нихромовых спиралях, вроде свои параметры выдала.

    12.6 V 3 A Charger, or Continuing the Discussion About Converting a Cordless Drill Battery 12.6 V 3 A Charger, or Continuing the Discussion About Converting a Cordless Drill Battery
    ​http://i.piccy.info/i9/2303cd2331503d582c23e54fddb54bba/1566272724/338760/13336
    72/P90530_160523.jpg
    ​​​
    Моя цель – доработать зарядку для большей универсальности. Сделать плавное уменьшение напряжения многооборотным потенциометром до 54, или возможно до 50 вольт, для зарядки 13S или 12S батарей. Так же сделать понижение тока, для менее емких батарей, либо «бережного» заряда меньшим током, когда зарядится можно не к спеху.
    Нарисовал схему вторички. Первичку рисовать не стал, вроде ничего интересного, собрана на AP3842CP, если кому интересно, нарисую.
    12.6 V 3 A Charger, or Continuing the Discussion About Converting a Cordless Drill Battery
    ​http://i.piccy.info/i9/6d3e5d632659481c94a71b11e189638e/1566273066/207086/13336
    72/zar5.jpg
    ​​​
    Выделенное синим цветом – детали не установлены, пустые места на плате.

    Мои мысли по этим темам:
    С напряжением, вроде всё просто. Отпаиваю одну ногу R21, в разрыв ставлю  переменный на 470ом. Вроде, все хорошо, напряжение должно уменьшаться где-то до 50V, и даже при обрыве не очень надежного китайского «крутистора», блок питания должен «заглохнуть».





    С током есть несколько вариантов. Вариант с изменением шунта отбрасываю, т.к. там большие токи, а есть желание регулировать или переключать, этот вариант только для стационарного исполнения.Вариант «поиграться» с нижним плечом делителя R34, тоже не лучший, хоть и есть пустые дырки под R37, но что туда не впаяй – если не менять номинал R34 будет уменьшение максимального тока БП. Далеко не линейная регулировка. И, при обрыве «нашего ноу-хау» получим на выходе «нежданчик» в виде макс тока в 5А.

    0
    1. 20 August 2019 07:45#11
      Вариант с верхним плечом делителя R40 лучше. Поднимаем одну ногу, в разрыв ставим переменник. У меня есть из подходящих номиналов только 10к и 47к. Думаю 10к будет маловато, он сможет понизить ток где-то до 3,4А.  47к наверно много, наверно нужно допаять к 47к «крутистору» в параллель обычный резистор где-то на 33к, получим макс около 19,4к, и около 2,5А на выходе. При обрыве такой цепочки, по идее ничего плохого произойти не должно, БП должен или «заглохнуть», или ограничить ток на мизере.

      Но, есть еще вариант, который манит меня своей простотой. Если не нужна плавная регулировка тока, а достаточно через какой-нибудь выключатель/кнопку с фиксацией, сделать два режима – максимальный ток и уменьшенный. (На этом же выключателе, можно отлично реализовать снижение оборотов кулера, когда включен пониженный выходной ток!). Тогда кидаем один контакт кнопки на землю, а вторым подключаем свой стабилитрон в параллель 5 вольтовому заводскому стабилитрону. Подключили стабилитрон на 3,3V – ток снизится приблизительно до 3,3А, 3V –получим 3А, 2,7V -получим 2,7А. Причем ток при котором сработает индикация завершения заряда, так же пропорционально уменьшиться! И будет составлять, приблизительно в зависимости от гистерезиса, как и задумано 1/10 от заданного выходного тока. 
      Если все таки хочется плавную регулировку, можно попробовать разорвать цепочку идущую от R40 и R25 к стабилитрону, и в разрыв запихнуть какой-то делитель на «крутисторе» который будет уменьшать напряжение 5В.

      Еще, в этой схеме есть интересный резистор R20, который видимо и задуман для отключения батареи после окончания заряда. О чем упоминал уважаемый Kirich в этой статье. Но, меня очень настораживает, почему китайцы его не впаяли, и не реализовали эту функцию… Возможно, блок питания вел себя не стабильно в таком режиме включения…
      Т.к. Я понимаю, чтобы задействовать этот резистор R20, придется пересчитывать делитель R16-19,R21,R23 – Я вряд ли буду с этим экспериментировать, мне будет банально лень… Тем более, я считаю, что нет ничего особо плохого, в том что батарея не отключается в конце заряда, а продолжает заряжаться низким током… Но, любопытно…

      Буду очень благодарен, уважаемому Kirich, и другим поклонникам этого ресурса, за любые комментарии, идеи, мысли, по всему выше сказанному!
      Прошу прощения, за много букв! Что-то меня понесло… smile
      Если здесь я это написал не к месту, перенесите на форум, или куда считаете нужным.


      +1

Discuss on the forumHave a question or some experience to share? Discuss the article with the author and readers: the forum is a convenient place to share schematics and photos.
Go to the forum

Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.

Log inRegister