125 mm angle grinder for Makita batteries
Today I’ll take a look inside, take it apart, run a few tests, and include a small bonus.
I’ll start with why I chose a cordless model. I often see comments along the lines of: Why get a cordless tool? You can use an extension cord with a regular one and work indefinitely (more or less), instead of stopping when the battery runs out.
Of course, you’re absolutely right—but only up to a point.
I have a corded angle grinder, but while renovating, I noticed that I used cordless tools much more often than corded ones. The reason is simple: there’s no cord to get tangled up in all the stuff on the floor, trip you up, or get in the way of a saw, drill, and so on. In the end, I use corded tools for larger jobs where there’s a lot of work to do in one place, and cordless ones when I need them “here and now.”
Unlike a screwdriver or drill, rotary hammer, or oscillating saw, an angle grinder isn’t a tool I use often. Still, I think it can be useful.
There was no branded packaging, just a plain, unremarkable cardboard box, dented in places.

The contents are just as basic:
1. Angle grinder
2. Guard
3. Handle
4. Wrench
Some of the items were wrapped in bubble wrap, but something still rattled around inside the box when I turned it over. I think they could have taken a little more care with the packaging, especially for such a heavy item. Still, nothing was damaged.

The wrench, handle, and guard are all standard. The only thing worth noting is that the guard is painted quite well: it slipped partly out of its bag during shipping, and the wrench knocked against it, but didn’t leave a mark.

And here’s the angle grinder itself. Its color scheme is somewhat reminiscent of Milwaukee tools, for example, their oscillating saw.

The front end is much like that of other angle grinders: spindle, clamping nuts, and spindle-lock button.

The biggest difference is probably the two LEDs for illumination, though I have my doubts that they’ll actually be much help.

The lower part of the locking mechanism and the nut.
The lower flange that the disc sits on is designed for accessories with a 22 mm bore.
The clamping nut has the same thread as the one on my corded Makita, but there’s a small difference in the wrench holes: one pair has the spacing for the supplied wrench, while the other pair is slightly wider, for a “Makita-style” wrench. Otherwise, the nuts are identical, right down to the groove layout.

The housing is rubberized in places and feels secure in the hand, with no slipping. The balance is good with the battery installed.

There’s an on/off switch on top. The mechanism isn’t very convenient: it’s held in place not by a switch lock, but by a protrusion on the housing itself. If that protrusion wears down, I’ll have to come up with a workaround.
There are three terminals underneath for connecting the battery. Tools designed for Makita batteries usually have two contacts, but I couldn’t figure out what the third one is for here. The grinder worked fine when connected only to the outer terminals, although the middle one is usually used for the lockout.
The auxiliary indicators and controls.
The display at the top shows:
A battery icon that gives a rough indication of the charge level.
SPD and AUTO modes.
A numeric display: two dashes when stopped, a spinning animation while running, and the charge level as a percentage from 0 to 100.
A percent sign that lights up when the charge level is displayed.
There are also temperature and, presumably, jam-protection symbols, but I haven’t seen them appear during use yet.
There are two control buttons and additional indicators underneath:
A speed-mode button switches between full speed and automatic mode. In automatic mode, the speed drops by about half, but if the load increases, the electronics automatically switch to full speed. The mode is shown both by the first LED next to the button and on the display above.
The second LED stays lit while the grinder is running.
A button for switching on the light, with a memory mode, i.e. If enabled, the light then turns on automatically, and the right-hand LED indicates that it is on.
There is one more detail: if the angle grinder has been off for more than 30–60 seconds and you then press the light button, the top indicator shows the battery charge as a percentage. If you press it sooner, it shows two dashes, just as it does in the normal shutdown state.

This isn't my first angle grinder. About 12 years ago I bought a compact corded Makita. You can probably tell from its appearance that it hasn't spent much time sitting on a shelf, although I do clean the dust and grime off it from time to time.
My angle grinder is designed for 115 mm discs, although the only actual difference from the 125 mm version is the diameter of the guard. The speed and power are exactly the same.

The cordless angle grinder weighs just under 1.6 kg, while the corded one weighs 1.96 kg (without the cord), so the difference is about 400 g.

Next, I'll take a brief detour to describe the different types of grinders.
To start with, there are two main types: straight grinders and angle grinders. Angle grinders are the most common and are often called "bolgarkas" (literally, “Bulgarian grinders”); the one in the photo is on the right.

I knew the difference between straight grinders and angle grinders well, but I hadn't considered that angle grinders themselves also differ.
It turns out that some angle grinders are designed to work with the disc horizontal, while others are designed for a vertical disc. The model reviewed here is intended for horizontal-disc operation, for example, surface cleaning. You might think it could be used for polishing, but since the speed isn't adjustable, we can rule that out.
Angle grinders designed to run with the disc vertical are better suited to jobs where you need to cut something.
The intended position is determined by the relationship between the plane of the disc, the controls, and the grip.
The top two photos compare it with my Makita, which is clearly designed for cutting: when your finger is on the switch, the disc is vertical. Its body is also universal, so it's comfortable to use in either position.
This angle grinder is clearly designed for horizontal-disc operation: the switch is under your finger, and the handle is more comfortable to hold. Of course, you can also cut with it, but it's simply less convenient. You also can't switch it off quickly without shifting your grip, which affects safety—the switch should be under your finger.
I also found a minor issue with the guard installation. If you try to cut something, it won't always be convenient: the guard may simply hit the surface your "something" is resting on. For example, I used a battery.
For surface cleaning, everything works fine; the guard fits as it should.
The fix is very simple: replace the guard mounting screw with a shorter one. Then it won't hit the gearbox mounting screw, and you can rotate the guard through a noticeably wider angle. I didn't have a suitable screw, so I used one that was a little shorter and added a nut. The screw needs to be about 10–12 mm long, with an M6 thread.

As it turns out, there are quite a lot of angle grinders designed for horizontal-disc operation—perhaps even most of them. For example, the first cordless Makita I came across had the same configuration: the disc is horizontal when the button is under your fingers.
Some models let you simply rotate the gearbox by 90 degrees, but the body design of the model reviewed here doesn't allow that.

The gearbox comes apart easily; the screws weren't even very tight. I tightened them more when I put it back together.

The inner bearing.

Then I removed the self-tapping screws and separated the two halves of the housing. I can say right away: unless you absolutely have to, don't do this—the reassembly is very awkward. I also noticed that one of the housing screws is longer than the others. Be careful: in the photo, they're laid out to match their respective holes.

The motor is brushless, as promised.

1. The windings use fairly thick wire, and the rear bearing sits in a plastic part of the housing.
2. The button appears to be sealed, and even has a rubber cap, but it doesn't latch; a catch on the housing handles that.
3, 4. The indicator slots into the housing. The LEDs for the work light are also mounted on this board.

The power section is located near the terminal block, while the board itself is almost completely potted.

Judging by the number of wires, this board handles almost everything, including both the power section and control. It also has LEDs and buttons.
The power stage has six LNC04R050 transistors mounted on a fairly substantial heatsink.

The front of the motor also has a bearing, and there’s a rubber ring that makes it very difficult to remove the front section. What’s more, the motor is effectively frameless: it won’t run without the front section, since that section is actually part of the motor.

At first, I didn’t have a compatible battery, so I ran the tests with a Milwaukee battery. I managed to fit it so the negative contact connected as intended, then connected the positive contact with a wire.

The first thing I checked was the light. As expected, it works, but shines everywhere except where you need it. Still, it can be useful: it doesn’t switch off right away, but stays on for about half a minute, which is genuinely handy.

While measuring the current draw, I noticed something interesting: in high-speed mode, the speed depends on the supply voltage, but in low-speed mode it’s regulated. So as the input voltage drops, the current falls in one mode and rises in the other.
Below is the current draw versus input voltage: low speed at the top, high speed at the bottom. You can also see that the power at the top remains constant.

The low-voltage cutoff kicks in at around 13.8 V, but the protection has a delay. In other words, if the voltage suddenly drops to, say, 13 V and then immediately rises back to 14 V or higher, it will keep running until the voltage falls below the threshold mentioned above. With a 5S battery, that works out to about 2.75 V per cell, which is perfectly reasonable.
After the protection trips, the light flashes for a while, which is also very reminiscent of Milwaukee.
While I was testing the cutoff threshold, I noticed that if the tool shuts off due to over-discharge, it slows down gradually. But if you switch off the power supply output with the tool running, it stops instantly.

A little bonus: a quick look at the Makita battery case.
Since I don’t own any cordless tools that use Makita batteries, I had to order a battery case separately and assemble it myself. Besides, I’m planning to expand my tool collection a bit. Sure, I could have bought a battery locally, but that would have cost more and wouldn’t have been nearly as much fun :)
Anyway, as soon as I ordered the angle grinder, I ordered a battery case too. It arrived a little later, which is why I experimented with the Milwaukee battery. I’ll keep this brief, but if there’s interest, I may write a more detailed review.

The kit included everything needed, right down to the stickers.

The inside is a holder for ten cells in a 5S2P configuration.

The holder is very well designed, with spacing between the cells and protection for the positive terminals.
There are three types of contact plates: positive, negative, and interconnects. The interconnects are all identical. The quality is excellent; everything fits and is secured by tabs in the case. The whole thing is very thoughtfully designed, so it’s impossible to assemble it incorrectly.

The board is supposedly a new version, dated 2020. It has a temperature sensor to protect the battery from overheating during use, plus a separate thermal fuse for protection while charging.

I spent a long time trying to figure out where to install the thermal fuse, but the best I could come up with was putting it in the rectangular opening in the holder.

I used VTC6 cells from Nkon for the battery. Just a heads-up: when assembling the battery, install the cells first, then screw the holder together with the supplied screws (the middle screws), and only then weld on the plates!
The screws have hex-star heads, not Phillips heads, so keep that in mind too.

The cells were at roughly the same charge since they came from the same batch, so balancing was straightforward. First, I charged the whole pack to 21 V, until the current dropped to 1–1.5 A, then topped up each cell individually to full charge.
To avoid messing anything up, I first tinned the contacts and checked that at least the charge-level indicator came on.

After that, I soldered everything properly. Then I put it all together, applied the stickers, and weighed it out of curiosity: the battery weighs 628 g. Taking into account the 400 g weight difference between the grinder under review and the corded one, with the battery installed the cordless grinder is only about 200–250 g heavier.

The battery, fully assembled.

Now it's time for some field testing.

After the repair, I had at least one 125 mm disc left over. For comparison, on the right is a 115 mm Makita disc that came with my angle grinder. It's pretty old, of course, but still works fine.

The tests were done using a 35 × 1.2 mm steel mounting strip and the shank of a 13 mm carbide-tipped drill bit. The disc was new, 125 mm in diameter and 1.2 mm thick. The test pieces were secured to a large 50 mm-thick board.
I would have tested more, but the limited space made cutting extremely awkward.

I started with the steel strip, got a little carried away, and before I knew it had cut six pieces. The GIF shows two cuts; judging by the timing, they took 10 seconds.

Cutting the drill bit shank took a little longer, about 11 seconds per cut.

In the end, I had a small pile of offcuts. It would probably have been good to measure the RPM, but subjectively, I can say they were about 10% lower than with the corded grinder. The RPM dropped a little while cutting, but the corded angle grinder behaves exactly the same way.

The rated power of this angle grinder is 800 W. Measuring its actual power consumption is quite difficult, so I ran a slightly different test: I powered it from an adjustable power supply with an output current of up to 22 A, set to 20 V.
As it turned out, the 440 W the power supply could deliver wasn't enough, so I had to apply less pressure while cutting to keep the voltage from dropping. As a result, the cutting time nearly doubled. I think the actual power during the battery-powered tests was at least 600 W.

Of course, I was also concerned about how long this tool could run on a charge. Before starting, I fully charged the battery, then cut six pieces of strip and four pieces of drill bit shank. One of the pieces, though, was cut with the power supply (that took 0.1 Ah, by the way).
After that, I fully charged the battery again, and it took 0.45 Ah to recharge it. That seems quite economical to me. Of course, as the battery discharges, the RPM will drop and the process won't be as efficient, but it's still pretty good.

Toward the end, I decided to compare the grinder under review “face to face” with a Milwaukee tool. And sure enough, the color scheme and overall appearance are very similar. If they had also made it compatible with Milwaukee batteries, it would have been perfect—though there's nothing stopping anyone from making some kind of adapter.

Ideally, I would write up my conclusions after at least a month of use, and under heavy workloads rather than occasional use, but I don't have that opportunity yet.
For now, I can say that the “angle grinder” works, and works pretty well. I expected much worse results.
In terms of power, it's comparable to my corded one, perhaps a little weaker, but probably within the margin of error. It has a power-saving feature that automatically increases the RPM when a load is applied. I tried it and found it quite convenient, although at first I thought the speed change would cause a jerk.
The grip is different from my Makita, but I wouldn't say it gets in the way much while working, though the difference is noticeable.
As expected, the light shines wherever it wants, not where I need it.
In short, it cuts well, no worse than a corded grinder of a similar size, and uses power efficiently. The only question is how long it will last.
So I ended up with an angle grinder from Banggood, styled like a Milwaukee, with a “Makita” battery whose case I bought on Taobao and cells from Nkon. That's how it goes :)
The store offered a coupon for this review: BGAKGMRU, which brings the price down to $48.99.
18 вольтовый аккумулятор внутри 10 батареек, болгарку акум тен, что внутри китайской ушм, ушм тэн на аккум, ушм тен на акум отзывы, болгарка аккумуляторная 125 мм под макитовский аккумулятор обзор, 2, к каким ушм подходят аккумуляторы от makita dga518, какие обороты на болгарке макита китай аккумуляторной, собрать инструмент под макита аккумуляторный, болгарка макита 128 вольт время работы, аккумуляторная ушм с подшипником в редукторе, какие аккумуляторы идут в комплекте с болгаркой макита 125, какие аккумуляторы подходят для ушм ман крафт, ушм к которым подходят аккумуляторы макита, макита lxt bl к каким шлифмашинам подойдет?, к каким ушм подходит аккумулятор макита, ушм постоянного тока с напряжением 72 вольт, ушм аккумуляторная к которой подходят аакумуляторы макита, правильно установить защиту и ручку на акуммуляторную ушм, какие нужны батареи для болгарки китайской, тушка болгарки под аккумулятор макита, 3, ушм под аккумулятор макита 12 в, какой блок питания подойдет для батарей ушм
Questions and answers
How well does the 125 mm cordless angle grinder for Makita batteries work?
The author says it cuts about as well as a corded grinder of similar size. In AUTO mode, speed drops to roughly half and rises automatically when the load increases.
How much does the cordless angle grinder weigh?
It weighs just under 1.6 kg, compared with 1.96 kg for the author's corded Makita without its cable—a difference of about 400 g.
What did the charge-consumption test show?
After the test, recharging the battery took 0.45 Ah. The author considers this economical, while noting that speed will fall as the battery discharges.
The figures from this review are in the measurement database: Tools
Discounted products
You may be interested in
Discounted products
All the content on the site and the advice are free, but we’d be grateful for your support of the project and the channel!
Comments2
Only registered readers can comment. It takes a minute to sign up, and you can log in with the same account you use on the forum.
Log inRegister


Comments are published in their original language.