Measurement database: tools

The author likes the old tweezers: they are comfortable to use and hold their shape well.

The black tweezers are similar to the author's main pair and fairly comfortable, but more roughly made.

The unpainted tweezers are too stiff and uncomfortable; the author is unlikely to use them.

The author tried the precision tweezers but preferred to return to the ceramic pair.

The author mentions it only to compare its closing force with the other tweezers.

It runs quietly, but the author found its airflow insufficient.

It falls short of the stated 200 mA and cannot run quietly when regulated.

It runs relatively quietly and provides decent airflow; the author installed it in the power supply.

The compact cordless saw cuts well, though the author notes shortcomings with the guard and blade.

The 6 and 6.35 mm collets clamp normally, but the bore finish is poor; the 8 mm collet needs modification.

The router works well and has sufficient power, but its base is awkward and its guide is flimsy.

Ksger is more convenient to use but heats up more; the author considers the handle somewhat overpriced.

It drives more easily and quickly than the previous model, but feels unbalanced with a 5S2P battery.

It works adequately, but has a standard motor, no spindle lock, and no battery over-discharge protection.

High, unstable resistance makes the clips unsuitable for testing batteries.

The article describes a soldering iron rated up to 60 W with USB-C or XT-60 power, but reports no practical testing.

The tweezers handle 1206 and 0805 components well, though the tips are slightly misaligned and differ in length.

It cuts well, no worse than a corded grinder of similar size, though its service life is unknown.

Nearly like the TS100 in ergonomics and operation, but with flaws; the author considers it an excellent buy for $11.

The author liked the kit, which makes it quick to build a simple, functional and inexpensive station.

The hot-air gun works well and heats quickly, but has shortcomings in build quality and controls.

The set includes nearly everything needed, but some blades—especially those with Japanese teeth—disappointed.

A convenient four-wire holder supports cells up to 21700, but its large positive contact may cause problems.

A compact cordless rotary hammer drills well, but the included battery does not last long.

The router works well, but has many small flaws, some of which had to be corrected.

The programmer is a useful tool to have, though the author initially could not use it to update the tester firmware.

The author is pleased with the station’s build and usability, but the iron delivers less power than claimed.

The station solders well and holds temperature, but its controls are awkward and it needs modification for 220 V operation.

The author liked the versatile kit and bag, though crimping small terminals is difficult.

The bits center well and are symmetrically ground, but the holes’ exit is not entirely clean.

The jigsaw is well built, runs smoothly and has enough power, but lacks a guide rail and a vacuum adapter.

The station was generally pleasing: the hot-air gun and preheater work well, but the included iron is slow.

The programmer works well, supports many chips, and gained in-circuit programming after a simple modification.

The author praises the tool’s build, comfort and versatility, while noting its high price and slower operation.

The drill met expectations; the author praised its build quality, decent power, and metal gearbox.

The powerful, well-built hammer drill performed well in testing, though it heats up noticeably and is expensive.

The machine can produce detailed work in soft materials, but it is slow and limited by rigidity and software issues.

Comfortable and fast to use, but its battery ran out sooner than expected.

Lasts longer than the orange model, but is less comfortable and has less torque.

The fan provides good airflow but is very noisy at maximum power.

The heat gun is convenient and quiet, but poorly suited to PCB soldering because it lacks temperature stabilization and airflow falls with narrow nozzles.

The shaft is convenient to use, with a good chuck and no noticeable radial play.

The holder is convenient and secures the engraver well, but its joint seems weak and the clamp can scratch the table.

The author liked this convenient, reliable station, but its stock power is insufficient for multilayer boards.

The tripod is convenient but delicate and intended for careful use.

The author liked the iron: it solders well and became his main tool, though the cable should be replaced.

Suitable for occasional small jobs, but it overheats and is not suited to frequent soldering or fine electronics.

It has sufficient power and is comfortable to use, but heats up noticeably and needs breaks.

The attachments are varied, but poor centering and rough workmanship make the set inconvenient; the author does not recommend buying it.

Shaves a little more roughly than the Philips, but works without complaints, causes no irritation, and is well built.

The rangefinder impressed with its accuracy and ease of use; the author would buy one.

The fan fit and works well; a rubbing noise from shipping was easy to fix.

All tips work with the Aoyue 2738 after minor filing; the author finds them comfortable and recommends them.

The step drills bore thin metal easily and straight; the author recommends buying them.